Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Atlas Equipment SLP-7K
Summary of Contents for Atlas Equipment SLP-7K
- Page 1 Replace This With Cover PDF...
- Page 2 Read this entire manual before operation begins. Record below the following information which is located on the serial number data plate. Serial No. Model No. Date of Installation...
-
Page 3: Table Of Contents
Contents General Information..5 Product Identifi cation ..8 Packing/Transport/Storage..9 Product Description ..11 Technical Specifi... - Page 4 Indicates the direction of access for motor vehicles to the lift BOLD Important information TYPE WARNING: Before operating the lift and carrying out any adjustments, read Chapter 7 “Installation” carefully. All proper operations for a better functioning lift are shown. SLP-7K...
-
Page 5: General Information
• Any use of the machine made by operators who are not familiar with the instructions and procedures contained herein shall be forbidden. This manual is an integral part of the lift: it shall be given to the new owner if and when the lift is resold. SLP-7K General Information... - Page 6 The manufacturer has paid proper attention to the preparation of this manual. However, nothing contained herein modifi es or alters, in any way, the terms and conditions of manufacturer agreement by which this lift was acquired, nor increase, in any way, manufacturer’s liability to the customer. General Information SLP-7K...
- Page 7 The manufacturer is not liable for any mistakes made when drawing up this manual and reserves the right to make any changes due the development of the product, at any time. SLP-7K General Information...
-
Page 8: Product Identifi Cation
Manufacturer’s personnel in charge. Technical Servicing For all servicing and maintenance operations not specifi ed or shown in these instructions, contact the dealer where the machine was purchased or the Manufacturer’s Commercial Department. Product Identification SLP-7K... -
Page 9: Packing/Transport/Storage
(e.g. cranes, trucks) and hoisting means. Be sure also to hoist and transport the components securely so that they cannot drop, taking into consideration the package’s size, weight and center of gravity and it’s fragile parts. Hoist and handle only one package at a time Packing/Transport/Storage SLP-7K... -
Page 10: Storage And Stacking Of Packages
Packages must be opened paying attention not to cause damage to people (keep a safe distance when opening straps) and parts of the lift (be careful the objects do not drop from the package when opening). Packing/Transport/Storage SLP-7K... -
Page 11: Product Description
The electro hydraulic operation is described in detail in chapter 8. This chapter describes the lift’s principal elements, allowing the user to be familiar with the machine. Figure 1 - Lift Product Description SLP-7K... -
Page 12: Operation
In this way, the operator must verify that neither persons nor objects are within the safety area. If so, the fi nal lowering button can be pressed and the lift will be completely lowered. A beep sound is heard during the last travel. Product Description SLP-7K... -
Page 13: Technical Specifi Cation
If there is over 10% fl uctuation on the electrical power supply, it is suggested to use the voltage stabilizer to protect the electrical components and system from failure. Technical Specification SLP-7K... - Page 14 Pump Type Gear Flow rate 2.1 cm 4.8 cm Continuous working pressure 210 bar – 230 bar Peak pressure 250 bar Figure 2 – Layout Technical Specification SLP-7K...
-
Page 15: Hydraulic Power Unit
ASTM D 2270 Viscosity index 104 N° ASTM D 97 Pour point ~ 30 °C ASTM D 92 Flash point 215 °C ASTM D 644 Neutralization number 0.5 mg KOH/g Change hydraulic oil at 1 year intervals Technical Specification SLP-7K... - Page 16 Gear pump Parachute valve – P2 (optional) Motor Ssafety solenoid valve – P1 Non return valve Safety solenoid valve – P2 Pressure gauge Lowering solenoid valve Emergency hand pump Leveling cock – P1 Figure 4 – Hydraulic Plan Technical Specification SLP-7K...
- Page 17 Motor 2.2KW 1PH Lifting button Thermal relay Lowering/fi nal lowering button Transformer 80VA Safety engaging button Contactor DC Beeper Lowering solenoid valve Top limit switch Safety solenoid valve – P1 Safety height limit switch Safety solenoid valve – P2 Technical Specification SLP-7K...
- Page 18 Figure. 6 – Pneumatic Plan Lubricator/pressure regulator can be supplied by the manufacturer on request. The pressure in the pneumatic line must be kept around 6bar – 8 bar. Technical Specification SLP-7K...
-
Page 19: Safety
• carefully follow the safety indications applied on the machine and included in the manual; • observe the safety area during lifting; • be sure the motor of the vehicle is off, the gear engaged and the parking brake put on; Safety SLP-7K... - Page 20 The operator must be sure no one is in danger before operating the lift. Bumping Risk When the lift is stopped at relatively low height for working, the risk of bumping against projecting parts occurs. Safety SLP-7K...
- Page 21 Materials and procedures suitable for the designed parameters of the lift have been used by the manufacturer to build a safe and reliable product. Operate the lift only for the use it has been designed for and follow the maintenance schedule shown in the chapter “Maintenance”. Safety SLP-7K...
- Page 22 The presence of unauthorized persons next to the lift and on the platforms is strictly forbidden during lifting as well as when the vehicle has been already lifted. Any use of the lift other than that herein specifi ed can cause serious injury to people in close proximity of the machine. Safety SLP-7K...
-
Page 23: Installation
6 inches thick, and in conformity with local regulations. If a fl oor covering with the above mentioned requirements is not available, a foundation plate is needed, or some fi xing points should be used for fi xing areas SLP-7K Installation... - Page 24 Make sure that the hoses are clear of any moving parts. Make sure to keep the hoses and fi ttings clean from dust. Failure to do so may result in hydraulic line failure which may result in damage or personal harm. Installation SLP-7K...
- Page 25 Figure 13 – Hydraulic Connection SLP-7K Installation...
- Page 26 • Make sure the electric connections are in compliant with the wiring diagrams (fi gure 5) • Make sure this is no leakage or blow-up in the hydraulic line and pneumatic line • Make sure the lift is connected to the ground Installation SLP-7K...
- Page 27 • Raise the lift to the top position with the levelling cocks off; • Lower the lift completely with the levelling cocks on; • Follow this procedure and repeat raising and lowering the lift at least 5 times to bleed all the air out of the cylinders. Installation SLP-7K...
- Page 28 • If shimming is required, insert the shims as necessary around the anchor bolts. • With the shims and the supplied anchor bolts in place, tighten by securing the nut to the base. Installation SLP-7K...
- Page 29 • Loosen the nuts (3) of the limit switch and adjust it at the desired height; • Tighten the nuts after adjustment. After adjustment of the switches, make sure to fi x the switch protection (fi g.16-4) on the base. Failure to do so can damage the switches. Installation SLP-7K...
- Page 30 Before carrying out the checks with load, inspect the machine and check bolts and nuts for proper tightening. • repeat checks provided for by 7.10 section with the vehicle loaded • if the platforms weren’t leveled, repeat the 7.7 section Installation SLP-7K...
-
Page 31: Operation And Use
The power switch can be set in two positions: • 0 position: the lift electric circuit is not powered; the switch can be padlocked to prevent the use of the lift. • 1 position: the main electric circuit is powered. Operation And Use SLP-7K... - Page 32 fi nal travel Lift operation can be summarized into four steps: Lifting • Place the vehicle at the center of the platform and lock the extensions; • Check to make sure that the vehicle is secured; Operation And Use SLP-7K...
-
Page 33: Manual Emergency Lowering
• Hold the emergency button on the safety air valve located in the control unit; • Open the lowering solenoid valve by turning the emergency screw (3) counter clockwise to lower the lift. • Retighten the emergency screw clockwise after lowering the lift completely. Operation And Use SLP-7K... - Page 34 Tightening or loosening the screw can reduce or increase the lowering speed. After manual lowering of the lift, reset it to ordinary operating conditions. The lift cannot be lifted if the solenoid valves are opened. Operation And Use SLP-7K...
-
Page 35: Maintenance
The use of water or infl ammable liquid is strictly forbidden Be sure the rod of the hydraulic cylinders is always clean and not damaged since this may result in leakage from seals and lead to possible malfunctions. Maintenance SLP-7K... -
Page 36: Periodic Maintenance
• verify that all components and mechanisms are check not damaged Every 12 • a check of the electrical system to verify that months Electrical control desk motor, limit switches and control system panel operate properly must be carried out by skilled electricians Maintenance SLP-7K... -
Page 37: Troubleshooting
The lowering solenoid valve does Check and clean, if dirty, or pressed not close replace, if faulty The emergency screw of lowering Retighten the screw valve does not close The suction pump fi lter is dirty Check and clean if needed Troubleshooting SLP-7K... - Page 38 Replace, if needed The electric board is faulty Replace electric board Presence of air or dripping in the Bleed the hydraulic circuit The lift hydraulic circuit isn’t raising Check and replace if synchronous The cylinder gaskets are damaged necessary Troubleshooting SLP-7K...
- Page 39 Leakages or presence of air in the Bleed the hydraulic system hydraulic circuit The lift does not The pump fi lter is dirty. Check and clean if needed. lift or lower smoothly Check the seal and replace if The pump suction is blown needed Troubleshooting SLP-7K...
-
Page 40: Warranty
RETURNS: Products may not be returned without prior written approval from the Manufacturer. DUE TO THE COMPETITIVENESS OF THE SELLING PRICE OF THESE LIFTS, THIS WARRANTY POLICY WILL BE STRICTLY ADMINISTERED AND ADHERED TO. Warranty SLP-7K...
Need help?
Do you have a question about the SLP-7K and is the answer not in the manual?
Questions and answers