Atlas Equipment 90HSC Installation & Operation Manual
  1. Manuals
  2. Brands
  3. Atlas Equipment Manuals
  4. Lifting Systems
  5. 90HSC
  6. Installation & operation manual

Atlas Equipment 90HSC Installation & Operation Manual

9,0001b. capacity two-post overhead lift
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 90HSC and is the answer not in the manual?

Questions and answers

Related Manuals for Atlas Equipment 90HSC

Summary of Contents for Atlas Equipment 90HSC

  • Page 2 Revised: 12/ 8/ 2020 Read this entire manual before operation begins. Record below t he following inform at ion which is locat ed on t he serial num ber dat a plat e. Serial No. Model No. Dat e of I nst allat ion...

  • Page 3: Table Of Contents

    Contents Specifi cat ions ... . . 4 I nst allat ion Requirem ent ..6 St eps Of I nst allat ion ..8 Test Run .

  • Page 4: Specifi Cations

    Specifi cations 9-OHSC Clear Floor, Chain-Drive Features • Dual hydraulic cylinders designed and m ade t o ANSI st andard, ut ilizing NOK oil seal in cylinder. • Self- lubricat ing UHMW Polyet hylene sliders and bronze bush. • Single- point safet y release, and dual safet y design. •...
  • Page 5 9-OHSC Specifi cations W idt h M in im u m Lift in g Lift in g Lift in g Ove r a ll Ove r a ll Gr oss M ode l St yle Be t w e e n Pa d M ot or Ca pa cit y...

  • Page 6: I Nstallation Requirem Ent

    I nstallation Requirem ent Tools Required Rot ary Ham m er Drill ( Φ19) Carpent er ’s Chalk Ham m er Screw Drivers Level Bar Tape Measure ( 25ft ) Crescent Wrench ( 12” ) Pliers Rat chet Spanner Wit h Socket ( 28# ) Allen Head Wrench ( 6# , 3# ) Wrench set Vise Grips...
  • Page 7 Specifi cations Of Concrete Con cr e t e m u st a dh e r e t o t h e follow in g spe cifi ca t ion s. Fa ilu r e t o do so m a y r e su lt in t h e lift a n d/ or ve h icle fa llin g. 1.

  • Page 8: Steps Of I Nstallation

    Steps Of I nstallation A. Location of Installation Check and insure t he inst allat ion locat ion ( concret e, layout , space size et c.) is suit able for lift inst allat ion. B. Use A Carpenter’s Chalk Line To Establish Installation Layout Of Baseplate Fig.
  • Page 9 2. Move aside t he lift wit h fork lift or hoist , and open t he out er packing carefully, t ake off t he part s from upper and inside t he colum n, t ake out t he part s box, check t he part s according t o t he shipm ent part s list ( Se e Fig.
  • Page 10 5. Open t he bag of part s and check t he part s according t o part s box list ( Se e Fig.1 0 ) . Fig. 1 0 D. Position Posts Posit ion t he colum ns upright on t he inst allat ion layout . Posit ion t he offside colum n parallel t o t he power side colum n at t he approxim at e overall widt h ( 133 1/ 2”...
  • Page 11 E. Install Cables Fig. 1 2 9OHSC (SS) Steps Of Installation...
  • Page 12 F. Oil Hose Assembly Fig. 1 3 9OHSC (SS) Steps Of Installation...
  • Page 13 G. Install Locks And Lock Release Cables Connect ing direct ion of safet y cable View A View B Fig. 1 4 9OHSC (SS) Steps Of Installation...
  • Page 14 H. Install Limit Switch Control Bar Assem ble Lim it Swit ch Near Assem ble Cont rol Powerside Colum n Bar Bracket using M12* 20 Hex Fig. 1 5 Screw wit h Nylok Nut and Washer 9OHSC (SS) Steps Of Installation...
  • Page 15 I. Install Limit Switch Loose Screw of Drive Rod for adj ust m ent , hose Tight en t he screw aft er adj ust m ent Wire cable Fix prot ect ive rubber ring at cable exit Adj ust Drive Rod of Lim it Swit ch Fig.
  • Page 16 K. Position Column, Making Sure The Baseplate Aligns With The Chalk Line, Then Install The Protective Rubber Covers. Check The Columns Plumbness With Level Bar, And Adjust With The Shims If The Columns Are Not Level Check t he colum ns plum bness wit h level bar on front and side colum n...
  • Page 17 L. Install Power Unit And Oil Hose Tight en t he nut aft er inst alling t he power unit fi t t ing Fig. 2 0 Tight en all hydraulic fi t t ings, and fi ll t he reservoir wit h hydraulic oil. N ot e : For m a x im u m r e lia bilit y a n d du r a bilit y of you r At la s h ydr a u lic pow e r u n it ple a se u se H ydr a u lic Oil AW 3 2 .
  • Page 18 M. Fix Anchor Bolts 1. Prepare t he anchor bolt s ( Se e Fig. 2 1 ) . Fig. 2 1 Lock washer Washer 2. Using t he rot ary ham m er drill, drill all anchor holes and inst all t he anchor bolt s.
  • Page 19 N. Install Lifting Arms And Adjust The Arm Locks 1. I nst all t he lift ing arm s ( Se e Fig. 2 3 ) 2. Low er t he car r iages dow n t o t he low est posit ion and loosen t he nut ( Se e Fig.
  • Page 20 O. Install Electrical System Connect t he power source on t he dat a plat e of power unit . Make sure t he connect ion of t he lim it swit ch is correct . N ot e : For t h e sa fe t y of ope r a t or s, t h e pow e r w ir in g m u st con t a ct t h e fl...

  • Page 21: Test Run

    Test Run 1. Adj u st syn ch r on ou s ca ble Press UP but t on t o lift t he carriages up t o t he posit ion of t he cable nut higher t han chain pulley. Use wrench t o hold t he cable fi t t ing, m eanwhile use rat chet spanner t o t ight en t he cable nut .
  • Page 22 4. Te st w it h loa d Aft er fi nishing t he above adj ust m ent , t est run t he lift wit h a load. Run t he lift t o a low posit ion several t im es fi rst t o m ake sure t he lift can raise and lower synchronously and t he locks can lock and release synchronously.

  • Page 23: Operation I Nstructions

    Operation I nstructions Ple a se r e a d t h e sa fe t y t ips ca r e fu lly be for e ope r a t in g t h e lift To lift ve h icle 1.

  • Page 24: Maintenance Schedule

    Maintenance Schedule M on t h ly: 1. Re- t orque t he anchor bolt s t o 86 foot pounds; 2. Check all connect ors, bolt s and pins t o insure proper m ount ing; 3. Lubricat e cable wit h lubricant ; 4.

  • Page 25: Trouble Shooting

    Trouble Shooting TROUBLE CAUSE REM ED Y 1. But t on does not work 1. Replace but t on 2. Wiring connect ions are not in good 2. Repair all wiring condit ion connect ions Mot or does not 3. Mot or burned out 3.

  • Page 26: Exploded View

    Exploded View M ode l 9 - OH SC Drive I n Fig. 3 2 9OHSC (SS) Exploded View...
  • Page 27 Cylin de r s Fig. 3 3 At la s M a n u a l Pow e r Un it 220V/ 60HZ/ 1 phase Fig. 3 4 9OHSC (SS) Exploded View...
  • Page 28 Illustration Of Hydraulic Valve Fig. 3 5 9OHSC (SS) Exploded View...

  • Page 29: 9-Ohsc Parts List

    9 - OHSC Parts List I t e m Pa r t # D e scr ipt ion Qt y. N ot e 211010B Wire Cable 202001B Powerside Colum n 620059 Prot ect ive Ring 209049 Plast ic Pulley 209010 Snap Ring 209008 Safet y Cover...
  • Page 30 I t e m Pa r t # D e scr ipt ion Qt y. N ot e 209022 Washer 209023A Arm Lock 201041 Lim it Ring 209024 Arm Lock Bar 209025 Hair Pin 209026 Spring 209027 Prot ect ive Rubber Set 201043A Lift ing Arm - Front 201047...
  • Page 31 I t e m Pa r t # D e scr ipt ion Qt y. N ot e 202011 Cont rol Bar 206025C Connect ing Pin for Cont rol Bar 206023 Nylok Nut 206041 Hex Bolt 206042 Cont rol Bar Support Bracket 206011 Cup Head Bolt 206013...
  • Page 32 Pa r t s For H ydr a u lic Pow e r Un it , 2 2 0 V/ 5 0 H z/ 1 ph a se I t e m Pa r t # D e scr ipt ion Qt y.

  • Page 33: Warrant Y

    W arranty Th is it e m is warrant ed for fi ve ( 5) years on st ruct ural com ponent s, t wo ( 2) years on hydraulic cylinders, and one ( 1) year on elect ric or air / hydraulic power unit s from invoice dat e. Wear it em s are covered by a 90 day warrant y.

Table of Contents