Table of Contents
Advertisement
Quick Links
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit
guide
About this document
Scope and purpose
The EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit enables the development of applications based on
EZ-USB™ FX20 USB 3.2 Gen 2x2 device controller (CYUSB4024-BZXI) for streaming video and audio seamlessly
to the USB host using the off-the-shelf FPGA add-on board and camera modules.
Intended audience
This document is intended for the EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit users.
User guide
Please read the sections "Important notice" and "Warnings" at the end of this document
002-40732 Rev. *C
www.infineon.com
2025-03-25
Advertisement
Table of Contents
Related Manuals for Infineon EZ-USB FX20 DVK
Summary of Contents for Infineon EZ-USB FX20 DVK
-
Page 1: About This Document
USB host using the off-the-shelf FPGA add-on board and camera modules. Intended audience This document is intended for the EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit users. User guide Please read the sections “Important notice” and “Warnings” at the end of this document 002-40732 Rev. *C www.infineon.com 2025-03-25... -
Page 2: Important Notice
Infineon Technologies. The design of the Evaluation Boards and Reference Boards has been tested by Infineon Technologies only as described in this document. The design is not qualified in terms of safety requirements, manufacturing and operation over the entire operating temperature range or lifetime. -
Page 3: Safety Precautions
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Safety precautions Safety precautions Note: Please note the following warnings regarding the hazards associated with development systems. Table 1 Safety precautions Caution: The evaluation or reference board contains parts and assemblies sensitive to electrostatic discharge (ESD). Electrostatic control precautions are required when installing, testing, servicing or repairing the assembly. -
Page 4: Table Of Contents
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Table of contents Table of contents About this document ........................1 Important notice ..........................2 Safety precautions .......................... 3 Table of contents ..........................4 Introduction .......................... 5 DVK contents ............................5 Download kit documents and hardware design files ................6 EZ-USB™... -
Page 5: Introduction
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Introduction Introduction The EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit is based on the EZ-USB™ FX20 product family of Infineon’s USB 20 Gbps device controllers. EZ-USB™ FX20 is a family of USB 20 Gbps peripheral controllers targeting the next-generation USB applications in camera, video, imaging, and data acquisition markets. -
Page 6: Download Kit Documents And Hardware Design Files
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Introduction Download kit documents and hardware design files Download the KIT_FX20_FMC_001 kit documents and the hardware design files from the EZ-USB™ FX20 kit webpage. The documents include a quick start guide (QSG), kit user guide (this document), and release notes. The hardware design files include schematics, bill of materials (BOM), and layout files. -
Page 7: Ez-Usb™ Fx20 Baseboard Features
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Introduction Figure 2 EZ-USB™ FX20 baseboard – bottom view EZ-USB™ FX20 baseboard features EZ-USB™ FX20 controller • Two QSPI SPI flash • Onboard regulators: 1.8 V and 3.3 V DC-DC switching regulators • Boot mode switch for selecting USB boot or SPI boot •... -
Page 8: Installing The Kit Software
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Installing the kit software Installing the kit software Download the EZ-USB™ FX20 SDK from the EZ-USB™ FX20 kit webpage. Install the following software. The installation of the following software may require administrator privileges. EZ-USB™ Control Center Download and install the EZ-USB FX Control Center application from the webpage. -
Page 9: Kit_Fx20_Fmc_001 System Design
KP3 PROG UART Connector Header Camera AUX Port AUX I/O diodes USB-FS RESET push SWD/ Optoisolator button JTAG/ Clock Infineon UART PDM Stereo microphone Power KitProg3 Board BOOT Mode supplies FX20 SWITCH GPIO accessory board I2S Audio Class-D Amplifier LEDs... -
Page 10: Kit_Fx20_Fmc_001 Ez-Usb™ Fx20 Dvk Design Details
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide KIT_FX20_FMC_001 system design KIT_FX20_FMC_001 EZ-USB™ FX20 DVK design details The KIT_FX20_FMC_001 EZ-USB™ FX20 DVK consists of the following: EZ-USB™ FX20 silicon (CYUSB4024-BZXI) • Two external QSPI Flash modules • Power supplies • 24 MHz crystal •... -
Page 11: Power Supply
QSPI flash (U6, U7) The kit has two Infineon S25FS256SDSNFI000 256 Mb QSPI flash devices. When the DVK is interface with an FPGA board, it is necessary to store the FPGA bin file in a flash memory. The DVK on-board flash modules can be used for this purpose. -
Page 12: Fmc Hpc Carrier Connector (J7)
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide KIT_FX20_FMC_001 system design 3.2.1.7 FMC HPC carrier connector (J7) The kit has an onboard ASP-134486-01 FMC HPC carrier connector that allows you to connect the FMC carrier boards. All unused signals of FMC mezzanine connectors are brought to the FMC carrier connector. FPGA boards can use these signals to communicate with the FMC carrier boards. -
Page 13: Programming The Kit
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Programming the kit Programming the kit The KIT_FX20_FMC_001 kit is preprogrammed with the internal colorbar firmware to stream 4K UVC color bar video generated internally inside EZ-USB™ FX20. This allows you to stream the color bar video without the need of an FPGA board. - Page 14 EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Programming the kit Do the following to program the device: Click FX3G2 USB BL > Click Program > Click Internal Flash Figure 6 Program in Control Center application Navigate to the <Drive>\EZ-USB FX20 Release Package\SDK\<project folder>\out folder based on the code example project.
- Page 15 EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Programming the kit Wait for programming to complete. Observe the EZ-USB™ FX20 device detach message in the Log window Figure 8 Programming successful Log window User guide 002-40732 Rev. *C 2025-03-25...
-
Page 16: Run The Application (Internal Color Bar)
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Run the application (internal color bar) Run the application (internal color bar) Viewing the UVC output using windows camera application 1. Follow the instructions in the SDK user guide to build the uvc_inmem project 2. -
Page 17: Viewing The U3V Output (Color Bar) Using Ebus Player Application
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Run the application (internal color bar) 5. On a USB 3.2 Gen 2x2 host, the frame rate will be ~124 fps. This can be viewed on the serial terminal such as Tera Term. Take a USB-C FS cable and connect its one end to J3 and the other end to a PC. Open any serial terminal application such as Tera Term. - Page 18 EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Run the application (internal color bar) 4. Open eBus Player application and do the following: a) Go to Select/Connect b) Select the available device. For example, FX3G2 c) Press OK Figure 12 eBus Player settings 5.
-
Page 19: Troubleshooting
RESET EZ-USB™ FX20: (Either press the RESET switch SW1 and release or power cycle the kit) c) Release the PMODE switch after a delay If you have any questions, create a support request on the Infineon Technical Support page. -
Page 20: References
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide References References [1] Infineon Technologies AG: EZ-USB™ FX20 kit webpage; Available online [2] Infineon Technologies AG: EZ-USB™ FX20 datasheet; Available online User guide 002-40732 Rev. *C 2025-03-25... -
Page 21: Glossary
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Glossary Glossary active authentication (AA) debug access port Electromagnetic Compatibility Electrostatic discharge Firmware JTAG Joint test action group LVDS Low-voltage differential signaling Pulse density modulation QSPI Quad serial peripheral interface Software development kit Serial peripheral interface Serial Wire Debug User guide 002-40732 Rev. -
Page 22: Revision History
EZ-USB™ FX20 DVK (KIT_FX20_FMC_001) kit guide Revision history Revision history Document Date Description of changes revision 2024-11-08 Initial release 2025-02-21 Updated FX20-related changes 2025-03-21 Updated FX20 webpage url 2025-03-25 Released to Web User guide 002-40732 Rev. *C 2025-03-25... -
Page 23: Disclaimer
For information on the types in question please contact your nearest Published by Infineon Technologies office. Except as otherwise explicitly approved by Infineon Infineon Technologies AG Technologies in a written document signed by 81726 Munich, Germany authorized...
Need help?
Do you have a question about the EZ-USB FX20 DVK and is the answer not in the manual?
Questions and answers