Vecow EAC-6000-OOB User Manual

Nvidia jetson orin nx edge ai computing system allxon oob, 2 gige lan, 3 usb 3.1, -25 c to 70 c operation

Hide thumbs

Table Of Contents

Quick Links

Download this manual

EAC-6000-OOB

NVIDIA

Allxon OOB, 2 GigE LAN, 3 USB 3.1, -25°C to 70°C Operation

Jetson Orin

™

NX Edge AI Computing System

USER

Manual

1.0.0 Edition 20240812

Table of Contents

Need help?

Do you have a question about the EAC-6000-OOB and is the answer not in the manual?

Questions and answers

Summary of Contents for Vecow EAC-6000-OOB

Page 1 USER USER EAC-6000-OOB Manual Manual NVIDIA ® Jetson Orin ™ NX Edge AI Computing System Allxon OOB, 2 GigE LAN, 3 USB 3.1, -25°C to 70°C Operation 1.0.0 Edition 20240812...
Page 2: Record Of Revision
Record of Revision Version Date Page Description Remark 1.00 2024/08/12 Official Release ©Vecow EAC-6000-OOB User Manual...
Page 3: Declaration Of Conformity
This manual is released by Vecow Co., Ltd. for reference purpose only. All product offerings and specifications are subject to change without prior notice. It does not represent commitment of Vecow Co., Ltd. Vecow shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of the product or documentation or any infringements upon the rights of third parties, which may result from such use.
Page 4: Order Information
A NVMe SSD is included in default. Please refer to NVMe SSD List to select NVMe SSD capacity. NVMe SSD List Part Number Description S128 128GB NVMe SSD S256 256GB NVMe SSD S512 512GB NVMe SSD S01T 1TB NVMe SSD ©Vecow EAC-6000-OOB User Manual...
Page 5: Optional Accessories
160W, 24V, 85V AC to 264V AC Power Adapter with 3-pin PWA-160W-WT Terminal Block, Wide Temperature -30°C to +70°C DIN-RAIL DIN Rail Kit 5G Module 5G Module with Antenna 4G Module 4G/GPS Module with Antenna WiFi & Bluetooth WiFi & Bluetooth Module with Antenna ©Vecow EAC-6000-OOB User Manual...
Page 6: Table Of Contents
CHAPTER 1 GENERAL INTRODUCTION 1.1 Overview 1.2 Features 1.3 Product Specification 1.4 Mechanical Dimension CHAPTER 2 GETTING TO KNOW YOUR EAC-6000-OOB 6 2.1 Packing List 2.2 Front Panel I/O & Functions 2.3 Main Board Expansion Connectors 2.4 OOB Board Expansion Connectors 2.5 Main Board Jumper / Switch Settings...
Page 7 CHAPTER 4 SOFTWARE SETUP 4.1 Peripheral Interface Guide 4.2 Flash image to Your EAC-6000-OOB 4.3 Install the JetPack Package 4.4 Software Ignition Control 4.5 Enable OOB Management Services 4.6 Troubleshooting Your OOB Enabler APPENDIX A : Power Consumption APPENDIX B : Supported Module List...
Page 8: Chapter 1 General Introduction
Medical Imaging, High-speed AOI, Mobile Robots and any AIoT/Industry 4.0 applications. The EAC-6000-OOB is equipped with rich I/O interfaces, including 2 GigE LAN ports, 1 USB 3.1 Gen 2 port, 2 USB 3.1 ports, 2 COM RS-232/422/485 ports, 1 CAN Bus port, and 7 GPIO pins.
Page 9: Features
• 1 CAN Bus supports Flexible Data-rate, 7-bit GPIO • DC 9V to 50V wide range power input, Ignition Power Control • Supports 24/7 secure remote monitoring, control, and optional Out-Of-Band management for disaster recovery empowered by Allxon ©Vecow EAC-6000-OOB User Manual GENERAL INTRODUCTION...
Page 10: Product Specification
• 1 Force Recovery Button • 1 Reset Button • 1 Micro USB Console Port Micro USB • 1 Micro USB Recovery Port 2 SIM Card Socket Power, SSD Antenna 10 Antenna for WiFi/4G/5G/LTE/GPRS/UMTS ©Vecow EAC-6000-OOB User Manual GENERAL INTRODUCTION...
Page 11 -40°C to 85°C (-40°F to 185°F) Humidity 5% to 95% Humidity, non-condensing Relative Humidity 95% @ 70°C Shock Operating, MIL-STD-810H, Method 516.8, Procedure I Operating, MIL-STD-810H, Method 514.8, Procedure I, Vibration Category 4 CE, FCC, EN50155, EN50121-3-2 ©Vecow EAC-6000-OOB User Manual GENERAL INTRODUCTION...
Page 12: Mechanical Dimension
1.4 Mechanical Dimension Unit : mm (inch) 231.0 (9.09) 212.0 (8.35) 193.0 (7.60) ©Vecow EAC-6000-OOB User Manual GENERAL INTRODUCTION...
Page 13: Chapter 2 Getting To Know Your Eac-6000-Oob
GETTING TO KNOW YOUR EAC-6000-OOB 2.1 Packing List Item Description EAC-6000-OOB Edge AI Computing System(According to the configuration of your order, EAC-6000-OOB may contain micro SD and M.2 modules. Please verify these items if necessary.) Item Description Outlook Usage Terminal block 3-pin...
Page 14: Front Panel I/O & Functions
2.2 Front Panel I/O & Functions 2.2.1 Functions of EAC-6000-OOB series In Vecow EAC-6000-OOB series, Most of the I/O connectors are located on the front panels. Most of the general connections to computer devices, such as POWER CON, IGN CON, COM, USB 3.0, LAN (RJ-45), Digital Display Port, GPIO, POWER BUTTON,RESET BUTTON, LED indicators are placed on the front panel.
Page 15 OS. 2.2.1.4 Ethernet Port There are two 8-pin RJ-45 jacks supporting 10/100/1000 Mbps Ethernet connections on the front side of EAC-6000-OOB series. It supports 1000BASE-T gigabit data signals over standard Ethernet Cat 5/Cat 6 cable. LAN Chip...
Page 16 There is a USB 3.2 Connector connections available supporting up to 10Gb per second data rate in the front side of EAC-6000-OOB series. It also compliant with the requirements of Super Speed (SS), high speed (HS), full speed (FS) and low speed (LS).
Page 17 There are 2 USB 3.2 Gen1 Connector connections available supporting up to 5Gb per second data rate in the front panel of EAC-6000-OOB series. It is also compliant with the requirements of Speed (SS), High Speed (HS), Full Speed (FS) and Low Speed (LS).
Page 18 It can be connected by USB (Type A to Micro USB Type) Cable to USB Port of PC, and execute terminal tool, then it will get the system status message. Pin No. Function USB_DATA- USB_DATA+ ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 19 Flash Recov The EAC-6000-OOB USB Recovery mode provides an alternate boot device (USB). In this mode, the system is connected to a host system and boots over USB. This is used when a new image needs to be flashed. USB0 must be available to use as USB Device for USB Recovery Mode.
Page 20 2.2.1.14 Nano SIM SIM 1 SIM 2 Flash Recov The external Nano SIM card offers wireless communication capability by M.2 key B 4G/5G Card to the system. ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 21 The power voltage of each GPIO pin is 0V to 3.3V. The maximum current can be 100mA. GPIO Connector Pin Out: Pin No. Function RSV_GPIO_P00 RSV_GPIO_P01 RSV_GPIO_P02 RSV_GPIO_P03 RSV_GPIO_P04 RSV_GPIO_P05 RSV_GPIO_P06 2.2.1.16 CAN Port CAN Bus Connector Pin Out: Pin No. Function CANH1 CANL1 ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 22 There are 8-pin RJ-45 port supporting 10/100 Mbps Ethernet connections in the OOB-100. The pin assignment of CN6 is listed in the following table: Pin No. 10/100 Mbps E_TX+ E_TX- E_RX+ ----- ----- E_RX- ----- ----- ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 23 The SIM card sockets do not support hot-plug. Please make sure to unplug the system power before inserting the SIM card(s). If you want to support hot-plug, you need to set the SW4 to SIM card detection function. ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 24: Main Board Expansion Connectors
SOM_DIMM SIM2 FLASH PORT LAN2 LAN1 PWR_CON ATX_PWR_CON M12_LAN2 M12_LAN1 BOT View of MB UART_CN1 OOB_CN1 JIGNMODE1 M2M_CN1 DOWNLOAD PORT M2B_CN1 M2B_CN2 M2E_CN1 MICRO SD JAUDIO1 JUSB1 B2B_CN1 JUART PWR_LED HDD_LED ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 25 2.3.1.1 B2B_CN1 Board to Board Connector B2B_CN1 B2B_CN1 connector apply to EAC-6000-OOB-CB and EAC-6000-OOB- PE board use. Host I/Fs supported MIPI CSI x4 transfer GMSLx4 with Fakra Connector and PCIe x1 transfer 4 GigE with PoE LAN. Definition Definition Definition...
Page 26 ,2 is RS-232, if you want to change to RS-422 or RS-485, it must change COM mode by DIP SW ( COM1 SW5, COM2 SW4). Pin No. Description COM_DTR COM_CTS COM_TXD COM_RTS COM_RXD COM_DCD ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 27 The connector include 7 bit GPIO with 3.3 power level, it can be set GPI or GPO mode what you want. Pin No. Definition PWR 5V PWR 3.3V GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 28 2.3.1.5 CN6: Reserve I2C/SPI The connector include I2C and SPI bus for reserve application. Pin No. Definition PWR 5V PWR 3.3V I2C1_SCL I2C1_SDA SPI1_SCK SPI1_MISO SPI1_MOSI SPI1_CS0 ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 29 The connector is connected by OOB daughter board, if you want to remote control the system function (Power on / reset or monitor). Definition Definition Definition PWR 5V OOB_SDA PWR 5V OOB_RXD OOB_TXD PSW_NU GPIO0 RST_SW GPIO1 OOB_SCL PWR_DET ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 30 2.3.1.9 M2M_CN1 : M.2 Key M Slot M2M_CN1 The M.2 key M connector is suitable for applications that use Host I/Fs supported PCIe Gen 4 x4, it can be plugged NvME Module card 2280 type. ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 31 2.3.1.12 M2E_CN1 : M.2 key E Slot M2E_CN1 The M.2 key E connector is suitable for applications that use wireless connectivity including Wi-Fi, Bluetooth, NFC of GNSS. Module card types include 2230. ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 32 The connector is connected by OOB cable, it can transfer the debug UART signal to OOB, and it will monitor by Ethernet remote the system status. The UART Signal is switched by SW9. ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 33: Oob Board Expansion Connectors
2.4 OOB Board Expansion Connectors 2.4.1 Top view ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 35 OOB-100 supports 2 screw type terminals. 2.4.5 CN3: Mini PCIe slot There are Mini PCIe slots supported with USB 2.0 signal in the OOB-100. (USB must be selected as the host mode by SW1). ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 36 Pin No. Definition Pin No. Definition +3.3V +1.5V LED_WPAN LED_WLAN / SIM_DET +3.3V LED_WWAN +3.3V USB_D+ USB_D- SMB_DATA SMB_CLK +1.5V +3.3V Reserved Mechanical Key UIM_VPP UIM_RESET UIM_CLK UIM_DATA Reserved UIM_PWR +1.5V +3.3V ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 37 The all signal with voltage 3.3V level. The pin assignment are listed in the following table: Pin No. Definition Pin No. Definition DC +5V input DC +5V input GPIO0 GPIO1 UART_TX UART_RX I2C_SCL I2C_SDA PWR_SW RST_SW PWR_DET ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 38 Disable edge device power detection function USB port host mode USB port device mode 2.4.8 SW2: LAN reset button Users will be able to reset the network settings by long pressing the button. ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 39 There are two function selected by SW4. The DIP switch setting of SW4 is listed in the following table: Function Mini PCIe pin 44 WLAN LED function. Mini PCIe pin 44 for SIM card detection function. ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 40 UART and JTAG. The all signal with voltage 3.3V level. The pin assignment are listed in the following table: Pin No. Definition Pin No. Definition +3.3V JTAG_nTRST JTAG_TDI JTAG_TMS JTAG_TCK JTAG_TDO RESET UART1_RX UART1_TX ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 41: Main Board Jumper / Switch Settings
2.5 Main Board Jumper / Switch Settings 2.5.1.1 Board Top View of EAC-6000-OOB Main Board with Jumper. The figure below is the top view of EAC-6000-OOB series main board. It shows the location of the jumpers. Top Side JPOE_PWR1 ©Vecow EAC-6000-OOB User Manual...
Page 42 2, or 2 and 3. Open Closed Closed 2-3 You may configure your card to match the needs of your application by DIP switch. As below show the DIP switch on and off. ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 43 2.5.1.2 JP3 : SOM_FAN1 Operation Voltage Select Pin No. Definition PWR 5V FAN1PWR PWR 12V 2.5.1.3 JPOE_PWR1: PoE Power On Select Mode JPOE_PWR1 Pin No. Definition 3V3ALW_PWRON 3V3_PWRRUN VCC3_PWRON 2.5.1.4 SW5/SW4 : COM1/COM2 Port Mode Select ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 44 • Check Table 2 for choosing the related resistor • 1T/1R RS-422 • TX Enable Low Active with Auto Sensing (also mean Full Duplex Auto Direction Control) • Check Table 2 for choosing the related resistor ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 45 If the system use the ignition mode, the function can be changed by jumper setting. The default is H/W setting, it can be changed by software, but the jumper must be changed Pin 2-3 short. Pin No. Definition H/W MODE(Default) S/W MODE ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 46 The UART and OOB only option 1. Please refer as below function Table. Pin No. Definition 3.3V On Channel SW8.1 On Channel SW8.2 AUDIO **Please make sure the power off when you're changing the switch.** ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 47 2 , 4 OFF CONSOLE 1 , 3 OFF RXD_FT 2 , 4 ON TXD_FT ---------- ---------- TXD_FT ---------- ---------- MICRO_B_RXD ---------- ---------- OOB-RXD ---------- ---------- MICRO_B_TXD ---------- ---------- OOB-TXD ---------- ---------- ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 48: Ignition Control
2.6.1 Adjust Ignition Control Modes EAC-6000-OOB series provides 16 modes of different power on/off delay periods adjustable via SW6 switch. The default DIP switch is set to 0 in ATX power mode. SW6 : Ignition Control...
Page 49 Please find below the general wiring configuration. For testing purpose, you can refer to the picture blow to simulate ignition signal input controlled by a latching switch. ©Vecow EAC-6000-OOB User Manual GETTING TO KNOW YOUR EAC-6000-OOB...
Page 50: Chapter 3 System Setup
SYSTEM SETUP 3.1 How to Open Your EAC-6000-OOB Step 1 Remove four F-M3x4L screws. Step 2 Pick up bottom cover. ©Vecow EAC-6000-OOB User Manual SYSTEM SETUP...
Page 51: Installing Nano Sim Card
3.2 Installing Nano SIM Card Step 1 Remove two F-M3x4L screw on SD/SIM cover. Step 2 Inserting SIM card, make sure the system power is not plugged. ©Vecow EAC-6000-OOB User Manual SYSTEM SETUP...
Page 52: Installing Micro Sd Card
3.3 Installing Micro SD Card Step 1 Remove one F-M3x4L screw on SD/SIM cover. Step 2 Inserting SD card. ©Vecow EAC-6000-OOB User Manual SYSTEM SETUP...
Page 53: Installing
3.4.1 M.2 Key E 2230 Step 1 Install M.2 Key E 2230 into slot and fasten one pan head M3x4L screw. 3.4.2 M.2 Key M 2280 Step 1 Install M.2 Key M 2280 into slot. ©Vecow EAC-6000-OOB User Manual SYSTEM SETUP...
Page 54 Step 2 Install M.2 Key M cover into slot. Step 3 Fasten one pan head M3x4L screw and two F-M3x4L screw. ©Vecow EAC-6000-OOB User Manual SYSTEM SETUP...
Page 55 3.4.3 M.2 Key B 3042 Step 1 Install transfer bracket into nut and fasten one pan head M3x4L screw. Step 2 Install M.2 Key B 3042 into slot and fasten one pan head M3x4L screw. ©Vecow EAC-6000-OOB User Manual SYSTEM SETUP...
Page 57: Installing Antenna Cable
3.5 Installing Antenna Cable Step 1 Remove the rubber corks on the panel. Step 2 Install the cable with nut and washer indicated. ©Vecow EAC-6000-OOB User Manual SYSTEM SETUP...
Page 58: Mounting Your Eac-6000-Oob
3.6 Mounting Your EAC-6000-OOB 3.6.1 Wall Mount Install wall mount bracket then fasten four pcs F-M3x4L screw. 3.6.2 DIN Rail Mount Install din rail kit then fasten two pcs F-M3x4L screw. ©Vecow EAC-6000-OOB User Manual SYSTEM SETUP...
Page 59: Software Setup
API” on the desktop. 4.2 Flash image to Your EAC-6000-OOB Before starting the flashing process, be sure the EAC-6000-OOB is turned off and disconnected from the power. You also need to prepare a host computer running with Ubuntu 18.04 or later.
Page 60 Step 1: Connect the power adapter to the EAC-6000-OOB, The EAC-6000- OOB is not yet turned on at this time. Step 2: Connect the Micro USB cable to the “Flash” Port on EAC-6000-OOB and the other end to an available USB port on the host computer. You can connect up to five EAC-6000-OOB devices in recovery mode plugged in the host.
Page 61 4.3 Install the JetPack Package To install the JetPack package on EAC-6000-OOB, you can issue the following commands: $ sudo apt update $ sudo apt install nvidia-jetpack 4.4 Software Ignition Control Vecow provides Ignition Software to control power on/off delay periods.
Page 62 To get the best out of Allxon Services, ensure you are connected to a stable Internet connection. If your organization restricts Internet communications with the network using a firewall or proxy device, refer to the following webpage for detailed Information: Allxon Service Port/Protocol and Whitelist Information ©Vecow EAC-6000-OOB User Manual Appendix 3...
Page 63: Appendix A : Power Consumption
Storage M.2 Key M M.2 KEY E Intel AX210NGW LAN 1 1.0 Gbps LAN 2 1.0 Gbps Graphics Output HDMI Power Plan MAXN(16GB, 8GB) Power Source Chroma 62006P-100-25 Test Program Burn-in Test, Stress-ng Test ©Vecow EAC-6000-OOB User Manual Appendix A...
Page 64 Consumption 1.588A 14.29W 2.049A 18.44W 1.168A 14.02W 1.542A 18.50W ® ® 8-core Arm Cortex A78AE v8.2 64-bit 0.663A 15.92W 0.867A 20.82W CPU, up to 2 GHz 0.488A 17.55W 0.624A 22.46W 0.429A 21.43W 0.511A 25.55W ©Vecow EAC-6000-OOB User Manual Appendix A...
Page 65: Appendix B : Supported Module List
GPS, Glonass, Beidou and Galileo B.2 Supported Wi-Fi/Bluetooth List Type Model Support Standard SparkLAN_WNFT- IEEE 802.11ac/a/b/g/n M.2 KEY E 237ACN(BT) BT5.0 IEEE 802.11ac/a/b/g/n M.2 KEY E jjPlus JWW6051 BT5.0 IEEE 802.11a/b/e/g/h/i/k/n/r/u/v/w/ac/ax M.2 KEY E Intel AX210NGW BT5.3 ©Vecow EAC-6000-OOB User Manual Appendix B...
Page 66 No part of this publication may be reproduced in any form or by any means, electric, photocopying, or recording, without prior authorization from the publisher. The rights of all the brand names, product names, and trademarks belong to their respective owners. © Vecow Co., Ltd. 2024. All rights reserved.

Vecow EAC-6000-OOB User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Vecow EAC-6000-OOB

Summary of Contents for Vecow EAC-6000-OOB