Shark POWERDETECT NEVERTOUCH RV2800WD Series Owner's Manual page 12

MAINTENANCE
MAINTAINING THE BASE DUST BIN
Depending on the size of the base, empty the base
dust bin every 30 to 60 days or as needed.
To detach the bin, press the Dust Bin Release
button on the back right side of the base, then slide
out the bin.
CLEANING AND REPLACING THE BASE FILTERS
Regularly clean the filters to keep your vacuum's suction power optimal. Replace filters every 6-12
months or as needed.
IMPORTANT: DO NOT use soap when cleaning the filters.
CLEAN PRE-MOTOR FILTERS ONCE A MONTH
To open the filter housing lid, hold the top left edge
of the base and pull up on the lid. With the lid open,
remove the foam filter by the top handle, then lift out
the felt filter underneath. Tap the filters clean over the
trash, then rinse with cold water ONLY, as soap may
damage them. Allow filters to air-dry completely for
at least 48 hours before reinstalling to prevent liquid
from being drawn into electrical parts. The filters must
be installed correctly for the base to work properly.
Reinsert the felt filter first, then the foam filter.
s h a r kc l e a n . c o m
To empty the bin, hold it over the trash, then press
the release button with the trash can icon on the
side of the bin. The bin lid will open, releasing
dust and debris. Lightly tap the dust bin against
the inside of the trash receptacle to knock off any
remaining debris. Reinstall the bin by sliding it into
the slot in the base until it clicks into place.
CLEAN
POST-MOTOR
FILTER EVERY
SIX MONTHS
Press the
button at the
top of the
Filter Door,
then tilt the
door and lift
it off. Remove
the Post-Motor
Filter from
the base by
pulling the tab
down.
Tap the filters
clean over the trash. DO NOT use water or soap to
clean this filter as this will cause damage. More
frequent cleaning may be required with heavy use.
Reinstall the filer to the base by inserting the bottom
half first. Push filter until it clicks into place. Then
reinstall the filter door.
MAINTENANCE
CAUTION: Turn off power before performing any maintenance. To turn the base power off, simply unplug it
from the electrical outlet.
CLEANING THE PAD PLATE TRAY
ODOR NEUTRALIZER TECHNOLOGY
It is recommended to replace the Odor Neutralizer Technology every 6 months, or as needed.
1. Flip up the handle
and rotate the dial
counterclockwise
until the two arrows
are aligned. Pull the
handle to remove the
dial from the base.
2. Rotate the cartridge
counterclockwise in
the dial housing and
pull out the cartridge
to remove it.
3. Remove the new odor
cartridge from the
sealed packaging. To
maintain the life of the
cartridge, keep it in
the sealed packaging
until you are ready to
install it.
NOTE: The Odor Neutralizer Technology is not included in all models.
With the ramp removed, you can access the pad
plate tray.
To clean the pad plate tray, wipe it down with a
damp microfiber cloth.
For base models with pad wash: carefully remove
the grey water mesh on the left-hand side and clear
any debris, then reinstall.
Allow the tray to completely dry for at least 48
hours before reinstalling the ramp and the robot.
NOTE: Pad plate tray design may vary.
4. Align the yellow arrow on
the side of the cartridge
with the yellow arrow on
the side of the dial cover,
then insert the cartridge
into the dial. Rotate the
cartridge clockwise to lock
it in place.
5. Align the arrow on the dial
cover with the arrow on the
base, then reinsert the dial
into the base. Rotate the
dial counterclockwise until
it clicks into an intensity
setting to engage. Rotate
further to change the
intensity setting.
6. Dispose of the old
cartridge by dropping it
into the trash.
s h a r kc l e a n . c o m