Download
Share
Print this page
Shark PowerDetect Self-Empty XL RV2820VEUK Series Owner's Manual
  1. Manuals
  2. Brands
  3. Shark Manuals
  4. Vacuum Cleaner
  5. PowerDetect Self-Empty XL RV2820VEUK Series
  6. Owner's manual

Shark PowerDetect Self-Empty XL RV2820VEUK Series Owner's Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
with SELF-EMPTY BASE
Robot Vacuum
RV2820VEUK/AV2820VEUKWH SERIES
OWNER'S GUIDE

Advertisement

loading
Need help?

Need help?

Do you have a question about the PowerDetect Self-Empty XL RV2820VEUK Series and is the answer not in the manual?

Questions and answers

Related Manuals for Shark PowerDetect Self-Empty XL RV2820VEUK Series

Summary of Contents for Shark PowerDetect Self-Empty XL RV2820VEUK Series

  • Page 1 with SELF-EMPTY BASE Robot Vacuum RV2820VEUK/AV2820VEUKWH SERIES OWNER’S GUIDE...

  • Page 2: Important Safety Instructions

    29. DO NOT use to pick up: 37. For Shark® PowerDetect Self-Empty XL Do not operate the robotic vacuum be eight inches from any stairs (or must a) Liquids.
  • Page 3 GETTING TO KNOW YOUR SHARK POWERDETECT GETTING TO KNOW YOUR SHARK POWERDETECT Indicator Lights Front Bumper SELF-EMPTY BASE DOCK Button CLEAN Button FRONT Indicator Light Base Dust Bin LIDAR Module Odour Neutralizer Dial Post-Motor Filter Access Door Debris Intake Cliff Sensors...
  • Page 4 NOTE: Shark Robots use 2.4 GHz networks to connect. Typical home Wi-Fi networks support both 2.4 GHz and 5 GHz. Restart your phone • Turn off phone, wait a few minutes, then turn it back on and connect to Wi-Fi.

  • Page 5: Installing The Side Brush

    SELF-EMPTY BASE SETUP ROBOT INDICATOR LIGHTS Low Battery LEFT NOTIFICATION BATTERY WI-FI RIGHT LEFT LED pulsing RED Charging LEFT NOTIFICATION BATTERY WI-FI RIGHT 0.3m BATTERY LED pulsing RED for low, YELLOW for medium, GREEN for high If your robot is low on battery power, the left LED 0.3m light will pulse RED.
  • Page 6 CHARGING DOCK AND CLEAN BUTTONS IMPORTANT: Be sure to charge the robot completely before its first cleaning so that it can explore, map, and CLEAN BUTTON clean as much of your home as possible. It may take up to 6 hours to fully charge your robot. If the robot is on the base, press the CLEAN button for a whole-home clean.
  • Page 7 USING THE SHARKCLEAN APP AND VOICE CONTROLS website. Search for "Shark Skill". Select the Shark Skill to open the detail page, then select the Enable Skill option. Once enabled, you can ask Alexa to control your robot (i.e., "Alexa, tell Shark to start cleaning").

  • Page 8: Troubleshooting

    It is normal for your robot to temporarily lose connectivity when it goes under furniture, or moves far from your router. Your Shark robot will automatically reconnect to Wi-Fi. If the robot does not reconnect on its own, remove the unit from the Self-Empty Base. Power the robot off, wait 10 seconds, and place it back on the base.

  • Page 9: Maintenance

    MAINTENANCE MAINTENANCE MAINTAINING THE BASE DUST BIN CAUTION: Turn off power before performing any maintenance. To turn the robot power off, press the DOCK button on the robot for 5-7 seconds. EMPTYING THE ROBOT DUST BIN Depending on the size of the base, empty the base To empty the bin, hold it over the trash, then press dust bin every 30 to 60 days or as needed.
  • Page 10 MAINTENANCE MAINTENANCE CLEANING THE ROBOT'S FILTER CLEANING THE WALL-FOLLOW SENSORS For optimal suction power, after each use, clean the filter inside the robot's dust bin. 1. The sensors on the robot require occasional maintenance. 2. With a dry cloth or cotton swab, gently dust off the sensors located on the sides of the robot. Remove and empty the dust bin.

  • Page 11: Brush Roll

    RIGHT LED (YELLOW) Solid debris wrapped around the axles so they can move freely LEFT LED (YELLOW) + NOTIFICATION LED Wheel motor encoder failure. Please contact Shark (RED) + BATTERY LED (RED) + WIFI LED Customer Service at 0800 862 0453.

  • Page 12: Replacement Parts

    MAINTENANCE REPLACEMENT PARTS LIDAR MODULE CLEANING THE DIRTDETECT SENSORS Check the navigation module on top of the robot and gently remove any hair or debris. For a more complete clean, place the robot on a level surface and turn off the power. Use compressed air to blow away any dirt or debris from the gap around the rotating LiDAR module.
  • Page 13 Questions or Problems? END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE 0800 862 0453. IMPORTANT: PLEASE READ THE TERMS AND CONDITIONS OF THIS LICENCE AGREEMENT CAREFULLY CALL BEFORE COMMENCING USE OF THIS PRODUCT This End-User License Agreement (“EULA”) is a legal agreement between you and SharkNinja Operating LLC’s (“SharkNinja”, “us”...

  • Page 14: Manufacturer's Guarantee

    If you further agree to receive communications from us, you can also receive tips and advice on how to get the best out of your Shark appliance and hear the latest news about 7.
  • Page 15 NOTES NOTES s h a r kc l e a n . c o . u k s h a r kc l e a n . c o . u k...

  • Page 16: Register Your Purchase

    Expected runtime: 60 minutes Expected charging time: 6 hours PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE. This Owner's Guide is designed to help you keep your Shark PowerDetect robot running at peak performance. SharkNinja Europe Ltd, 1st/2nd Floor Building 3150,...

This manual is also suitable for:

Powerdetect self-empty xl av2820veukwh series622356298346