Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Avery Weigh-Tronix WI-152
Summary of Contents for Avery Weigh-Tronix WI-152
- Page 1 Model WI-152 Battery-Operated Indicator User’s Manual...
- Page 2 Weigh-Tronix reserves the right to change specifications at any time. 11/17/00 152_U.P65 PN 16926-0015e2 Printed in USA...
-
Page 3: Table Of Contents
Table of Contents Introduction ......................7 Operations Mode ....................7 Keyboard 1 Indicator Operation ....................9 Powering Up ....................9 Annunciators ....................9 Operations Mode ................... 10 Gross/Tare/Net Weighing Operations ............10 Gross Weighing ..................10 Net Weighing ..................... 11 Pushbutton Tare .................. - Page 4 WI-152 Specifications...
- Page 5 12-volt version 6-volt version...
-
Page 7: Introduction
Introduction Battery voltage level can be seen under the diagnostics menu. Operations Mode Keyboard... - Page 8 Figure 1 Keyboard layout...
-
Page 9: Indicator Operation
Indicator Operation Powering Up ASLEEP Figure 2 Indicator Display Gross Annunciators Tare lb, kg, gal Low Bat Motion Print Zero... -
Page 10: Operations Mode
Operations Mode This manual assumes the unit is config- ured to allow full access to all functions Service Manual Figure 3 Operations Menu MENU ® MENU ¬ SELECT ¯ SELECT GROSS/NET Gross / Tare / Net Weighing Operations Gross Weighing GROSS/NET ZERO... -
Page 11: Net Weighing
Net Weighing Pushbutton Tare ZERO TARE GROSS/NET GROSS/NET Clearing the Active Tare TARE MENU CLEAR TARE NO TARE GROSS/NET Entering, Retrieving and Changing Values in MENU TARE Tare Registers... -
Page 12: Net Weighing Operation
If register 5 has an existing value and you wish to select that register value as your tare, you can press PRINT/SELECT to select that value, then press GROSS/NET to return to PRINT/SELECT. TARE weighing mode. There is a one-step way to accept a keyed in value and return to gross/net weighing mode. -
Page 13: Viewing And Setting Cutoffs
Viewing and Setting Cutoffs point point MENU CUTOFFS PRINT/SELECT 0. y... -
Page 14: Controlling Cutoffs
TARE/+/- MENU MENU PRINT/SELECT CUTOFFS Controlling Cutoffs To Access the Control MENU Control F unction Cutoff values (positive or SELECT HALtEd negative) must be entered before you can control them. -
Page 15: Key Functions During Cutoff Control
Key Functions During Cutoff Control To Activate and Control the Cutoffs HALtEd MENU SELECT r xxxxxx xxxxxx HALtEd SELECT h xxxxxx xxxxxx MENU r xxxxxx xxxxxx To Halt Active Cutoffs r xxxxxx h xxxxxx To Return to Gross/Net Weighing Mode GROSS/NET... -
Page 16: Cutoff Connections
Cutoff Connections Signal Name Pin Number +12v (on 12v units) + Relay Voltage Cutoff 1 Cutoff 2 Logic Ground Shield Shell Figure 4 Cutoff connection pin assignments Viewing and Setting Time MENU HOUR PRINT/SELECT If you enter an incorrect digit, press the ZERO/CLEAR key to clear the display one digit at a (09 40 A) -
Page 17: Viewing And Setting The Date
Viewing and Setting the Date MENU PRINT/SELECT If you enter an incorrect digit, press the ZERO/CLEAR key to clear the display one digit at a time. PRINT/SELECT GROSS/NET... -
Page 18: Transmitting Data
Transmitting Data Signal Name Pin Number Figure 5 RS-232 Connector pin assignments PRINT/SELECT PRINT Figure 6 Sample WI-152 Printout... -
Page 19: Communication Protocol
Communication Protocol Indicator Diagnostics Test Mode Figure 7 Test Menu... - Page 20 MENU TEST SEALED UNSEALED MENU MENU PRINT/SELECT PRINT/SELECT PRINT/SE- LECT MENU GROSS/NET VERSION DISPLAY DISPLAY PRINT/SELECT PRINT/SELECT MENU MENU PRINT/SELECT DISPLAY BUTTONS BUTTONS PRINT/SELECT MENU ON MENU BUTTONS OUTPUTS SEQUENCE CUTOFF 0 CUTOFF 1 BATTERY...
- Page 21 A to D SERIAL READY MENU LOOP LOOP LOOP NO LOOP...
- Page 22 Weigh-Tronix 1000 Armstrong Dr. Fairmont, MN 56031 USA Telephone: 507-238-4461 Facsimile: 507-238-4195 e-mail: industrial@weigh-tronix.com www.wtxweb.com Weigh-Tronix Canada, ULC 217 Brunswick Blvd. Pointe Claire, QC H9R 4R7 Canada Telephone: 514-695-0380 Facsimile: 514-695-6820 Weighing Products & Systems Weigh Bar ® is a registered trademark of Weigh-Tronix Inc.
Need help?
Do you have a question about the WI-152 and is the answer not in the manual?
Questions and answers