Advertisement
Instruction
Installation of Machine wireless board
Washers and Dryers with Compass Pro,
Washers and Barrier washers with Clarus Vibe &
Ironers with Vibe interface
Kit No. 988807401
Read the instruction in full
before starting work.
If anything is unclear or
incorrect, please contact
your local sales office or
service representative.
438907725/EN
2025.02.11
Advertisement
Table of Contents
Related Manuals for Electrolux Professional 988807401
Summary of Contents for Electrolux Professional 988807401
- Page 1 Installation of Machine wireless board Washers and Dryers with Compass Pro, Washers and Barrier washers with Clarus Vibe & Ironers with Vibe interface Kit No. 988807401 Read the instruction in full before starting work. If anything is unclear or incorrect, please contact your local sales office or...
- Page 3 Instruction 1 Safety Precautions for Machine wireless board Note! This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter- ference when the equipment is operated in a commercial environment.
-
Page 4: Dimension Drawing
Instruction 2 Dimension drawing 70 mm / 2.76 inch 45 mm / 2 inch fig.X03631 3 Contents of the kit fig.X02830A 432689401 Machine Wireless Board x 1 490624901 Machine Wireless Board cover x 1 471796002 Circuit support x 4 413327505 Harness RS232 Fuse IOT x 1... - Page 5 Instruction 4 Recycling instruction for packaging fig.X03238 Fig. Description Code Type Bubble foil PE-LD Low density polyethylene Cardboard packaging PAP 20 Corrugated card board...
-
Page 6: Network Overview
Follow the instructions carefully in order for a correct and safe installation and interconnection of the equipment. 5.1 Network overview To be able to use Electrolux Professional provided Connectivity and Management Software Tools, ELS network should be established. The Machine wireless board is a part of ELS Network, it should be installed on each machine with Compass Pro/Cla- rus Vibe control system or Vibe interface and it shall be connected to the CPU RS232 port via a quick connection port behind or on top of the machine. -
Page 7: System Requirements
Instruction WIFI-MESH • Fixed root (C) • Max. 16 layers (Y0–Y16) • Max. 6 children per node (B) • Max. 20 nodes (B) per root (C) L < 10m L < 10m fig.X03193 5.2 System requirements • Min. requirements for commercial router: –... - Page 8 Instruction 5.3 Installing the Machine wireless board 5.3.1 Positioning overview Dryers TD6–6 TD6–7 PD9C, TD6–10 TD6–14, TD6–20 TD6–17S, DE-635S, D735S TD6–16, DE-635, D735 TD6–45, DE-6100, D7110 TD6–24S, DE-650S, D750S TD6–30, DE-667, D767 TD6–60, DE-6135, D7145 TD6–37, DE-683, D783 Washers On washers the position shall be as the figure. There are two possible positions, A and B. fig.X02856...
- Page 9 Instruction Barrier washers For the following models the Machine wireless board shall be positioned on top of the machine as illustrated: WB6-20, WB6-27, WB6-35 WB6-70, WB6-90, WB6-110 WHB5500H, WH5500H Ironers For the IV648xx range the Machine wireless board shall be positioned as illustrated: IV648xx FFS...
- Page 10 Instruction 5.3.2 Procedure 5.3.2.1 Washers, Barrier washers & Dryers The same Machine wireless board kit can be installed on different machine models. The following figures shows TD6–7 model as an example but the procedure is the same for all machine models covered by this kit. Disconnect the power to the machine.
- Page 11 Instruction Remove the cover (2) from the Machine wireless board with the circuit supports (1 & 3). Squeeze on the top and bot- tom of the cover and then pull it out. fig.X02846A Snap on the Machine wireless board with the circuit supports (1 & 3) on the machine. fig.X02834A...
- Page 12 Instruction Connect the harness (4) to the quick connection (Y) on the machine and the other end to the Machine wireless board at position (Z). fig.X02841 Mount the cover (2) on the Machine wireless board. Press until you hear a “click”. Note! Arrange the harness in a loose bend according to the illustration.
- Page 13 Instruction 5.3.2.2 Ironers The same Machine wireless board kit can be installed on different machine models. The following figures shows IV648xx model as an example but the procedure is the same for all machine models covered by this kit. Disconnect the power to the machine. Remove the caps (1 &...
- Page 14 Instruction Connect the harness to the Machine wireless board at position (present of keyed connection). Note! The harness (4) included in the kit 988807401 is not used for the IV648xx range. fig.X03426A...
- Page 15 Instruction Snap on the Machine wireless board with the circuit supports (1 & 3) on the machine. Mount the cover (2) on the Machine wireless board. Press until you hear a “click”. fig.X03401 Connect the power to the machine. When the machine wireless board and the site wireless board have been installed, follow the attached INOM and the videos (scan on the QR code) to complete the provisioning.
- Page 16 Instruction 6 Button & LEDs for Machine wireless board A short press (< 1.5s) on the button is toggling the BLE on/off. fig.X03252 DL1: Yellow color / communication DL2: Red color / communication DL3: Green color / OTA DL4: Green color / Mesh WiFi DL5: Green color / Cloud (Server) DL6: Green color / BLE (Bluetooth Low Energy) DL7: Green color / Power...
- Page 17 Instruction DL4 / Mesh WiFi: On / searching Got a parent Connected to root (Site wireless board) fig.X03251C DL5 / Cloud (Server) • Off: Not connected to Cloud • On: Cloud connections work properly DL6 / BLE: Advertising Connected fig.X03251D DL7 / Power •...
- Page 20 Electrolux Professional AB 341 80 Ljungby, Sweden www.electroluxprofessional.com...
Need help?
Do you have a question about the 988807401 and is the answer not in the manual?
Questions and answers