Related Manuals for Innovative Concepts in Entertainment AIR FX PRO
Summary of Contents for Innovative Concepts in Entertainment AIR FX PRO
- Page 1 Service Manual Innovative Concepts in Entertainment 10123 Main Street Clarence, New York 14031 (716) 759-0360 8:30am to 6:00pm EST WWW.ICEGAME.COM...
- Page 2 Table of Contents Safety and Warnings Parts Included Game Assembly 5 - 18 Programming 18 - 19 Troubleshooting tests Warranty Rev C - 2-7-2024...
-
Page 3: Safety And Warnings Before You Begin
SAFETY AND WARNINGS BEFORE YOU BEGIN WARNING: WHEN INSTALLING THIS GAME, A GROUNDED A.C. RECEPTACLE MUST BE USED. FAILURE TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS. FAILURE TO USE A GROUNDED RECEPTACLE COULD ALSO CAUSE IMPROPER GAME OPERATION, OR DAMAGE TO THE ELECTRONICS. - Page 5 Parts included with your game. If you are missing any of the parts below please contact ICE service department. Monday through Friday 8:30am to 6pm Eastern standard time at (716) 759-0360. You can also visit our webpage at WWW.ICEGAME.COM A-AF1500X Playfield Top AF3586X Skirt A AF3586X Skirt B AF3518X Puck Tray...
-
Page 6: Step 1: (Attaching The Feet)
Step 1: (Attaching the Feet). Attach the feet to all four legs by inserting them into the hole at the bottom of the leg and turning the feet clockwise until flush to the leg. They will later be used to level the table top. -
Page 7: Step 4: (Base Assembly)
Step 3: (Base assembly). Just like with the back panel insert the electronics panel into the leg assembly and secure using two AA6212 washers and two AA6211 Allen bolts. Parts needed: Electronic panel AA6212 Qty 2 AA6211 Qty 2 Step 4: (Base assembly) Rotate the base so you can install the other leg assembly. - Page 8 Step 5: (Base assembly) Locate the right leg assembly. Slide it onto the four tabs and secure with four AA6212 washers and AA6211 Allen bolts. Make sure UP is toward the playfield top and OUT goes toward the floor. One person should support the base while the other person aligns the leg assembly into the tabs.
- Page 9 Step 7: (Base assembly) At the other end of the plug, cut the wire tie holding the Wire Cap to the AC cord. Then pull the tie wrap out and discard. Plug same wire color into the Wire cap as shown below.
- Page 10 Step 9: (Base assembly) Pull wire ties tight. Use your wire cutters to snip the excess strap. Locate other end of AC Cord and snap the two connectors together. Step 10: (Base assembly) If you want the cord to come out on the left side and the cord is too long, you can coil it up as shown below and secure with wire ties.
- Page 11 Step 11: (Speaker and Leg LEDS wiring) Located at each leg assemblies are two harnesses that need to be plugged. They are for the speakers (two pin harness) and LED lighting (eighteen pin harness). Step 12: (Speaker and Leg LEDS wiring) After moving the playfield top near the cabinet base, remove the four handles.
-
Page 12: Step 13: (Top Assembly)
Step 13: (Top assembly) Note at the bottom of the playfield there are two plates. They fit into the base where there are notches. The operator control panel is at the front of the playfield top. It must be installed at the same side as in the electronics panel and NOT to the back panel. - Page 13 Step 15: (Top assembly) Open the front access door and locate the three main harnesses and plug them in. There will be one more 3 pin harness for the air blower which will be plugged in later Step 16: (Blower install) Locate the blower assembly.
- Page 14 Step 17: (Blower install) Parts needed: Secure the blower using one AGF3527 bracket, two AA6212 Qty 2 AF3527 AA6212 washers and AA6211 Allen Bolts. AA6211 Qty 2 Step 18: (Blower install) Locate the power cable for the blower. It will be at the center where you plugged in the three main harnesses from step 9.
-
Page 15: Step 19: (Display Assembly)
Step 19: (Display assembly) The display harness will be inside the hole where the display mounts on the playfield top. This is the opposite side where the electronics door is located. Carefully pull the harness out of the hole. Step 20: (Display assembly) Then insert it through the display mount and then plug it into the display itself. - Page 16 Step 21: (Display assembly) Once the harness has been plugged in, insert the bottom bolts into the display mount. Then slide the display to lock it onto the mount. Secure the display using two AA6004 Phillip screws at the top. Tighten the lower screws once the upper ones are tight. Parts needed: AA6004 Qty 2 Step 22: (Display assembly)
-
Page 17: Step 24: (Ac Power)
Step 23: (Score assembly) Using two AA6211 Allen bolts attach one AF3518X puck holder at each end of the table. Parts needed: AF3518X Qty 2 AA6211 Qty 4 Step 24: (AC Power) Plug the AC cord into a grounded AC outlet. WARNING - ONLY PLUG INTO A GROUNDED OUTLET. - Page 18 Step 25: (AC Power) Press the “PWR” button located at the front of the game to turn the game on. How to configure your game While the game is in attract mode (not playing any game), press and hold the “SEL” button for three seconds.
- Page 19 NHL version SFX mode only toggles between 0 and 1 to enable/disable SFX.
- Page 21 Score Sensor Replacement (Either side) Remove the puck holder first. See step 23 for details. Then remove four Allen screws and washers along with three at the bottom. Pull the front cover away from the cabi- net enough to disconnect the push button, then remove. The sensor is attached by a plastic nut.
- Page 22 I.C.E. Inc warrants all components in new machines to be free of defects in materials and workmanship for the period listed below: ■ 180 days on Main PCB’s, Computers & Motors ■ 1 year on all LCD monitor panels ■ 90 days on all other electronic and mechanical components ■...
Need help?
Do you have a question about the AIR FX PRO and is the answer not in the manual?
Questions and answers