1. Manuals
  2. Brands
  3. advidia Manuals
  4. Security Camera
  5. M-46-V
  6. Quick manual

advidia M-46-V Quick Manual

Network fixed dome cameras
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
M-46-V
Network Fixed Dome Cameras
Quick Guide
V1.02
0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the M-46-V and is the answer not in the manual?

Questions and answers

Related Manuals for advidia M-46-V

Summary of Contents for advidia M-46-V

  • Page 1 M-46-V Network Fixed Dome Cameras Quick Guide V1.02...
  • Page 2 Waterproof Requirements Please waterproof cables in accordance with the following instructions. User shall assume all responsibility for device damage caused by water due to improper waterproof measures. NOTE!  Before you start, connect all the needed cables and cut off the copper wires for the cables that you don't use.
  • Page 3 Tighten Tighten Tighten Tighten Waterproof tape Wrap the unused cables together into a bundle 3. Install the supplied waterproof components to the network cable in sequence. CAUTION! You need to mount the rubber ring onto the network cable interface first. 4.

  • Page 4: Packing List

    Packing List Contact your local dealer if the package is damaged or incomplete. The attachments may vary with models, please see the actual model for details. Name Unit Camera Waterproof components （1） Screw components （2） Mount accessory （3） User manual Remarks: * means optional and supplied with certain models only.

  • Page 5: Maintenance

     Do not overbend the cables during the installation, otherwise, poor cable contact may cause malfunction.  When connecting to an external interface, use an existing connection terminal, and ensure that the cable terminal (latch or clamp) is in good condition and properly fastened.

  • Page 6: Internal Structure

    Φ127.0mm (5.04") Φ89.3mm (3.52") Type B Φ127.0mm (5.04") Φ89.3mm (3.52") Internal Structure Transparent dome cover Reset button Network Micro SD interface Card slot Safety wire Power interface 1. ALARM_OUTPUT_N 2. ALARM_OUTPUT_P...

  • Page 7: Cable Connection

    3. GND 4. ALARM_IMPUT 5. GND 6. AUDIO_IN 7. GND 8. AUDIO_OUT NOTE! Use a pin to press and hold the Reset button for about 15 seconds to restore factory default settings. Perform this operation within 10 minutes after the device is powered on or the reset will fail otherwise.

  • Page 8: Ceiling Mount

    Hot plugging is not recommended. Ceiling Mount The following part takes ceiling mount as an example. Wall mount is similar to ceiling mount and therefore is omitted here. The figures are for your reference only. Locate the holes, drill holes on the ceiling, and then mount the plastic rivets of self-tapping screws.
  • Page 9 Push the network cable head into the tapered sleeve. Cut a hole on the waterproof rubber stopper, and insert the network cable head through the opening. Remove the tapered sleeve. Connect the network cable to the network interface, and attach the rubber stopper to the interface for water proofing.
  • Page 10 Lens base Rotate the lens base horizontally. Fastening screw Loosen the fastening screws and rotate the lens vertically. Lens Rotate the lens horizontally. NOTE! The above steps are only applied to the camera with manual zoom lens. For how to adjust the display of the camera with motorized zoom lens, please see the Web of the camera.

  • Page 11: Access Your Camera

    NOTE!  The preceding installation process is concealed installation, during which holes are drilled in the ceiling and tail cable is led out from the top of your camera. Cables are connected and frapped at the ceiling side to prevent messy cables from affecting camera mounting.
  • Page 12 NOTE!  DHCP is enabled by default. If a DHCP server is used in your network, your camera may be assigned an IP address, and you need to use the assigned IP address to log in.  You may need to install a plug-in at your first login. Please follow the on-screen instructions to complete the installation and then open the browser again to log in.
  • Page 13 Disclaimer and Safety Warnings Copyright Statement No part of this manual may be copied, reproduced, translated or distributed in any form by any means without prior content in writing from our company (referred to as us hereafter). The product described in this manual may contain proprietary software owned by our company and its possible licensors.

  • Page 14: Network Security

    and recommendations in this manual are presented without warranty of any kind, expressed or implied, including, but not limited to, merchantability, satisfaction with quality, fitness for a particular purpose, and noninfringement.  Users must assume total responsibility and all risks for connecting the product to the Internet, including, but not limited to, network attack, hacking, and virus.

  • Page 15: Safety Warnings

     Disable the automatic login and save password features: If multiple users have access to your computer, it is recommended that you disable these features to prevent unauthorized access.  Choose username and password discretely: Avoid using the username and password of your social media, bank, email account, etc, as the username and password of your device, in case your social media, bank and email account information is leaked.
  • Page 16  Take proper waterproof measures in accordance with requirements before using the device outdoors. Power Requirements  Installation and use of the device must be in strict accordance with your local electrical safety regulations.  Use a UL certified power supply that meets LPS requirements if an adapter is used. ...
  • Page 17 2013/56/EC. For proper recycling, return the battery to your supplier or to a designated collection point. © i-PRO Co., Ltd. All Rights Reserved. i-PRO, Viewnetcam.com, Advidia, VideoInsight, CloUDE, and Unified Digital Evidence are registered trademarks or trademarks of i-PRO Co., Ltd. or i-PRO Americas Inc. in various jurisdictions. All other trademarks are the...

Table of Contents