Wacom STU-300B Manual
Also See for STU-300B:

Advertisement

Wacom STU-300B Manual

Connecting the tablet

The STU-300B can be connected to a host computer via a USB cable. Consult your Wacom Signature Solution Partner for the STU-300B and host computer connection.

Replacing the pen tip

The pen tip (nib) can wear with normal use. In the unlikely case that the nib gets too short or develops a sharp edge, you can replace it with spare nibs. For replacement of the pen tips please contact your Wacom Signature Solution Partner.

USB cable attachment

  1. Place the unit face down on a soft cloth to protect the display.
    USB cable attachment - Step 1
  2. Place the unit in front face.
    USB cable attachment - Step 2

Specification

Specification

PRECAUTIONS ON USE AND HANDLING

Be sure to follow all instructions, cautions, and warnings found within this guide.
Failure to do so could cause the loss of data or damage to your computer. Failure to do so could also void your warranty, in which case Wacom shall have no responsibility to repair or replace the product.

Usage

Do not use the STU-300B LCD signature tablet in a facility control system that requires extremely high reliability; it may cause other electronic devices to malfunction, or other devices may cause the LCD signature tablet to malfunction. Where use is prohibited, power off the STU-300B to prevent the possibility of it causing other electronic devices to malfunction. Wacom does not accept any liability for direct or consequential damages.
For details, please refer to your Warranty located at the end of this guide.

Environment

Do not use or store the LCD signature tablet where:

  • Temperature changes are severe or exceed specifications (e.g., outdoors or inside a vehicle).
  • The LCD signature tablet and pen are exposed to direct sunlight or heat from an appliance, or are exposed to water or any other kind of liquid.

Do not use the LCD signature tablet in a dusty environment; this may damage the unit.

Handling

High Voltage. Do not open or disassemble the STU-300B LCD signature tablet. There is a risk of electrical shock when the casing is open. This will also void your warranty and Wacom shall have no responsibility to repair or replace the product.
If the LCD screen has been damaged, DO NOT touch any liquid that may be leaking from it; this liquid is an irritant. In case of contact with skin, eyes, or mouth, rinse immediately with running water for at least 15 minutes or more. If contact is made with the eyes or mouth, also consult a physician.
Prevent children from swallowing the pen tip. The pen tip may accidentally be pulled out if children are biting on them.


Do not disassemble the pen. This may cause the device to malfunction. In this case, Wacom shall have no responsibility to repair or replace the product.
Do not scratch the display screen. Avoid placing sharp objects on the display screen surface.
Avoid intensive shock or vibration to the STU-300B or the pen. Hitting or dropping the LCD signature tablet may damage the display screen or other components.
Do not put heavy articles on the LCD signature tablet or push against it with a strong force; this may damage the display screen.
Do not place heavy articles on the STU-300B cabling, repeatedly bend the cables sharply, or apply heavy stress to the cable connectors; this may damage the unit or cabling.
If the pen tip becomes sharp or angular, it may damage the coating on the display screen.
Please replace the pen tip if necessary.
Move the product periodically to another place on your work surface to avoid permanently discoloring or altering the appearance of the surface.
Do not use any organic solvent (e.g., alcohol) or even mild detergent to clean the display screen.
Use of these cleaners can damage the coating on the screen.
Please note that damage of this kind is not covered by the manufacturer's warranty.

  • To clean the display screen, use an anti-static cloth or a slightly damp cloth. When cleaning, apply only a light amount of pressure to the display screen and do not make the surface wet.
  • To clean the LCD signature tablet casing or pen, use a soft cloth with mild detergent (such as dish washing liquid) diluted with water.

Do not expose the STU-300B to high voltage electrostatic discharges or to a build-up of an electrostatic charge on the LCD screen. This may result in a temporary blotching of the LCD monitor. If blotching occurs, leave the STU-300B's display on and the blotching should disappear within a few hours.

Service
The STU-300B is part of a complete solution that has been delivered by a third party.
Please contact your Wacom Signature Solution Partner for any support.

Note on use
When LCD panel is operated continuously for long period, a trace of electric charge remains near the electrode inside the LCD, and residual or "ghost" image of the previous image may be (image Persistence).
To avoid image persistence, Wacom recommends the use of a moving screen saver when the screen is turned on but idle.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Wacom STU-300B Manual

Advertisement

Need help?

Need help?

Do you have a question about the STU-300B and is the answer not in the manual?

Questions and answers

Table of Contents