Summary of Contents for JK ERGOLINE SUNDASH Series
Page 1
G L O B A L S E R V I C E E R G O L I N E S U N D A S H / F L A I R / PA S S I O N S E R I E S S O LT R O N X X S / X S S E R I E S OPERATING INSTRUCTIONS...
Page 2
Operating instructions (Part I) Ergoline SUNDASH / FLAIR / PASSION SERIES Soltron XXS / XS Series 1006322-00 / us / 09.2009...
Page 3
Contact Information Technical Service: JK Global Service A Div of JK Products & Services, Inc. #1 Walter Kratz Drive Jonesboro, AR 72401 800-445-0624 870-935-9046 e-mail: support@jkamerica.com http://support.jkamerica.com See also Operating Instructions Part II (15 min or 20 min): • Ergoline SUNDASH series •...
Table of contents Table of contents General ....................5 Definitions....................5 Identify your tanning device..............5 Information for the studio operator ............6 Intended use...................6 Foreseeable misuse ................6 Obligations of the studio operator............6 Staff training ...................7 Guidelines ....................7 Installation location.................7 2.6.1 Ventilation ..............7 2.6.2 Limits of installation location...........8 Export .....................8 MP3 music (optional)................8...
Page 5
4.10 Cleaning or replacing UV lamps and filter panels in the canopy...28 4.11 Cleaning or replacing interior lighting ...........29 4.12 PASSION series: Cleaning or replacing the canopy accent lighting..29 4.13 Cleaning the base filter .................30 JK-Products, Inc. – Limited Warranty..........31 Limited Acrylic Warranty ...............32 Warranty Claims ...................32 5.2.1 Policy &...
General General Definitions (Studio) operator People who provide tanning devices to users on a commercial basis. The operator is responsible for the orderly operation of the device as well as the compliance with the maintenance intervals. User A person who uses the tanning device at a commercial location. Staff People who are responsible for the operation, cleaning as well as general maintenance work and who instruct the users in the operation of the devices.
Information for the studio operator Information for the studio operator Intended use The tanning device is intended exclusively for cosmetic tanning of the human skin. This device is used for tanning one adult person at a time. • The user must wear suitable eye protection to block UV radiation during •...
Information for the studio operator Staff training As the operator you are obligated to train your personnel and instruct them in the established legal and accident prevention regulations. Ensure that your staff have understood and observe these instructions. This includes: •...
Information for the studio operator 2.6.2 Limits of installation location The tanning device must not be operated outside of buildings. For altitudes greater than 6500 feet above sea level a conversion must be carried out to ensure trouble-free operation. Please contact Customer Service (see Page 2) before carrying out the conversion and starting up the unit for the first time.
Disposal of recyclable materials The device has been produced of recyclable materials. When being scrapped, the device must be disposed of properly. JK Products & Services can provide you with information on the content and potential hazards of the materials used.
Operation Operation Mandatory reading Always read and follow all instructions for proper usage prior to allowing anyone to use the tanning device. The operating instructions included with this device must always be followed to prevent possible injuries. Inform users – to use provided UV-blocking protective eyewear whenever the equipment is energized.
Operation A further negative consequence of make-up is that the appearance of the skin deteriorates irreversibly over a period of time regardless of the quality of cosmetics used. Therefore, remove all make-up before a session in the sunbed. Showering after leaving the sunbed? The browning is in the skin, not on it.
Operation Operation overview: FLAIR / PASSION / XS 3.4.1 Navigation The device is operated with the navigation ring. Switch on UV lamps: – Press the button once. Switch off UV lamps/pause tanning: – Hold the button down. Select device function (go to pictogram) e.g.
Operation Start The device is started automatically with an internal or external timer. NOTE: Timer instructions see separate manual (order no. 0070923801-..) 3.5.1 Preparation time Example: Before the UV lamps turn on, you have a few minutes to prepare yourself. During the preparation time you can switch on the UV lamps at any time by pressing the START/STOP button.
Studio customers can connect their own MP3 player to the device when the “Stereo Sound System PLUS” accessory is available Jack plug (JK Part # 4630911001-..) provided for use by the studio operator (2 x 3.5 mm stereo jack plug).
Cleaning and maintenance Cleaning and maintenance Safety instructions for cleaning and maintenance EXTREME DANGER – HIGH VOLTAGE! You can be killed or injured by an electric shock! DANGER! During maintenance work there is a risk of touching live parts and receiving a fatal electric shock.
Page 17
Cleaning and maintenance Should you require any assistance or need additional information, please call Global Service USA at 800 445 0624, Monday through Friday 8:00 a.m. - 7:00 p.m. CT, Saturday 8:00 a.m. to 3:00 p.m. WARNING! Injuries and damage due to improper maintenance! WARNING! If the maintenance intervals for the UV lamps are exceeded or incompatible UV lamps are installed, the share of harmful UVB radiation may increase.
Cleaning and maintenance Malfunctions The display shows error codes to make it easier to localize the cause of the problem. – If a malfunction occurs, the error code flashes in the display. – If several malfunctions occur, the error messages are displayed alter- nately.
Cleaning and maintenance 4.3.2 Cleaning of surfaces Acrylic surfaces CAUTION! Do not rub with a dry cloth – danger of scratching! – For hygienic proper cleaning of acrylic surfaces, use a specially developed disinfectant cleaner. Other cleaning agents, especially concentrated disinfectants or solvents (e.g.
The current operating hours of the parts requiring maintenance can be displayed in the Presetting mode – see separate instructions “Presettings”. Please note that the device must be inspected regularly by a JK authorized representative every 12 months (from date of commissioning) to maintain its proper condition! 4.5.1...
Cleaning and maintenance Disassembly for cleaning and maintenance work Where necessary the base, the canopy panel or the front panel can be disassembled. EXTREME DANGER – HIGH VOLTAGE! You can be killed or injured by an electric shock! DANGER! During maintenance work there is a risk of touching live parts and receiving a fatal electric shock.
Cleaning and maintenance 4.7.1 Removing the base – Remove the screws and remove the washers. – Push the base to the rear in order to lift it out of the guide. – Remove the base and carefully lay it aside. The assembly is the same process in reverse order.
Cleaning and maintenance 4.7.2 Removing the canopy panel – First remove the outside screws and then remove the screws in the middle. – Support the canopy panel with one hand so that it does not fall down. – Press lightly against the canopy panel in order to lift it out of the guide. –...
Cleaning and maintenance 4.7.3 Removing the front panel – Remove the base: see page 21. – Remove the screws from the inside. – Carefully lift the upper edge on the front panel out of clamps (pull upwards). – Lift the front panel in order to lift it out of the two lower hooks. –...
Cleaning and maintenance Instructions for changing the lamps The UV effect of the lamps and thus the tanning effect decreases over the course of time. As such, the replacement intervals specified in the maintenance plan must be adhered to. UV filters are utilized in order to control the UV radiation, e.g. the filter panels on the facial tanner.
Cleaning and maintenance 4.8.2 Starter • Replace faulty starters immediately. You can recognize a faulty starter by the blackened ends of the UV low- pressure lamps or when the UV low-pressure lamps can no longer be started. Operating a UV low-pressure lamp with a faulty starter significantly shortens its service life.
Page 27
Cleaning and maintenance – Only utilize original UV lamps. – Only touch new lamps in the handling zone. 07229 / 0 – Check the function of the safety switch. The safety switch is located on one of the corners of the reflector. The safety switch ensures that the device switches off in the event of a faulty filter panel.
Cleaning and maintenance Cleaning or replacing UV lamps in the sunbed base – Remove the base: see page 21. – Remove the intermediate panel and carefully set aside (only for devices with an air conditioning unit). – Remove the lamp coverings at the head and foot ends. Replacing the lamps: see page 24.
Cleaning and maintenance 4.10 Cleaning or replacing UV lamps and filter panels in the canopy – Remove the canopy panel: see page 22. – Remove the lamp cover. Replace the lamps: UV low pressure lamps: see page 24. UV high-pressure lamps and filter panels: see page 25. Replace the starter: see page 25.
Cleaning and maintenance 4.11 Cleaning or replacing interior lighting – Remove the canopy panel: see page 22. Replace the lamps: see page 24. Replace the starter: see page 25. The assembly is the same process in reverse order. When assembling the sunbed please note: –...
Cleaning and maintenance 4.13 Cleaning the base filter – Remove the front panel: see page 23. – Pull out the two outside filters to the front. Remove the middle filter via the top. – Moist or dry clean the filter. Dry cleaning: Vacuum cleaner (depending on the degree of soiling) Moist cleaning: Water and detergent, or with a dishwasher.
10 days after purchase to insure valid registration and coverage for potential claims. If the warranty card is not registered, proof of purchase from JK-Products, Inc. or its authorized dealer or distributor will be required prior to any consideration on warranty claims.
JK-Products, Inc. – Limited Warranty Limited Acrylic Warranty JK Products, Inc. warrants its acrylic sheets to be free from defects in material and workmanship, under intended normal use, for a period of one (1) year from date of sale of the tanning bed. Due to the tanning lotions, cosmetics, disinfectant and improper cleaners used on tanning surfaces that cannot be controlled by JK Products, Inc., after the first thirty (30) days of warranty...
Each dealer/distributor has their own internal procedure for handling Warranty Claims and credits. NOTE: JK-Products, Inc., the manufacturer, does not involve itself in the direct handling of a Warranty Claim except where mitigating circumstances apply and where required by law.
Page 35
This warranty is not transferable and is only applicable to the original pur- chaser named on a completed and registered warranty record at JK-Products, Inc. headquarters. JK Products, Inc. obligations do not include transportation charged on the shipping of new components to the customer or on the return of defective components of the manufacturer.
Signs which warn of danger areas are attached to the device. The signs shown below are examples. Ensure that the instruction signs are always clearly recognizable and easily legible. Example: PASSION 40/3 1 Nameplate MODEL NO. JK Products and Services, Inc. #1 Walter Kratz Dr. Jonesboro, AR 72401 1-800-SUNDASH SERIAL NO.
Page 37
Appendix 2 Warning sticker 12076 / 0 3 USA mains connection sticker (1504659-..) 11995 / 0 The sticker is visible when the front panel is removed and the control unit cover opened. 4 USA power supply units sticker The sticker is visible when the front panel is removed and the control unit cover opened.
Page 42
G L O B A L S E R V I C E J K G lo b a l S e r v i ce A D i v o f J K P ro d u c t s & S e r v i ce s , I n c . #1 Walter Kratz Drive Jonesboro, AR 72401 Phone: 800-445-0624...
Need help?
Do you have a question about the ERGOLINE SUNDASH Series and is the answer not in the manual?
Questions and answers