Download Print this page
Curt Group LUVERNE 321802 Installation Manual

Curt Group LUVERNE 321802 Installation Manual

Advertisement

Quick Links

INSTALLATION MANUAL
Level of Difficulty
Moderate
Installation difficulty levels are based on time
and effort involved and may vary depending on
the installer level of expertise, condition of the
vehicle and proper tools and equipment.
Parts List
Qty Description
1
Grille guard*
1
Mounting bracket, driver side
1
Mounting bracket, passenger side
1
Upper mounting bracket, driver side
1
Upper mounting bracket, passenger side
2
Double bolt plate
2
Single bolt plate
14
Flat washer,12mm x 32mm OD x 3mm
10
Lock washer, 12mm
10
Hex nut,12mm
2
Hex bolt, 10 - 1.5mm x 30mm
4
Flat washer,
10mm x 27mm OD x 3mm
2
Nylon lock nut, 10 - 1.5mm
Hex bolt, 12 - 1.5mm x 35mm
4
Adhesive Foam
2
* Grille guard sold separately
Tools Required
Ratchet
Socket set
Torque wrench
Socket extensions
Torque Specifications
M8 bolt
22 ft-lbs.
M10 bolt
42 ft-lbs.
M12 bolt
74 ft-lbs.
M16 bolt
150 ft-lbs.
7/16" bolt
30 ft-lbs.
1/2" bolt
40 ft-lbs.
Use above torque setting unless otherwise noted
LUVERNETRUCK.COM
Product Photo
NOTICE
Visit www.luvernetruck.com for a full-color copy of this
instruction manual, as well as helpful videos, guides and much more!
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
Periodic inspection of your product should be performed
to ensure all hardware and / or components remain secure.
To help prevent damage to the product or vehicle, refer to the specified
torque specifications when securing hardware during the installation process.
Maintenance
Mild automotive detergent may be used to clean the product. Do not use dish detergent, abrasive
cleaners, abrasive pads, wire brushes or other similar products that may damage the finish.
Product Registration and Warranty
LUVERNE stands behind our products with industry-leading warranties. To get copies of the product
warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys
PRODUCT SUPPORT: 877.287.8634
321802-INS-RA
01/04/2021
ECN7433
PAGE 1
321802

Advertisement

loading
Need help?

Need help?

Do you have a question about the LUVERNE 321802 and is the answer not in the manual?

Questions and answers

Summary of Contents for Curt Group LUVERNE 321802

  • Page 1 INSTALLATION MANUAL 321802 Level of Difficulty Product Photo Moderate Installation difficulty levels are based on time and effort involved and may vary depending on the installer level of expertise, condition of the vehicle and proper tools and equipment. Parts List Qty Description Grille guard* Mounting bracket, driver side...
  • Page 2 Step 1 Remove the factory tow hooks and hardware, if equipped. NOTICE Tow hooks cannot be reinstalled with the grille guard. Vehicles without tow hooks: Cut out the indented area in both sides of the plastic bumper insert to clear the brackets as pictured. NOTICE Make several small cuts for best fit.
  • Page 3 Step 3 Select a 12mm single bolt plate. Secure the bracket to the bolt plate with a 12mm flat washer, one 12mm lock washer and one 12mm hex nut. Snug but do not fully tighten hardware at this time. Step 4 Repeat step 2 to install the passenger-side mounting bracket.
  • Page 4 Step 8 Locate the two factory hex bolts securing the top of the bumper to the inner bumper bracket. Remove the outer hex bolt. Reuse the factory outer hex bolt to secure the top bracket to the back of the bumper. Do not tighten hardware at this time.