Download Print this page
Ruijie RG-WALL 1600-Z5100-S Hardware  Installation And Reference Manual
Ruijie RG-WALL 1600-Z5100-S Hardware  Installation And Reference Manual

Ruijie RG-WALL 1600-Z5100-S Hardware Installation And Reference Manual

Cloud-managed firewall

Advertisement

Quick Links

Ruijie RG-WALL 1600-Z5100-S
Cloud-Managed Firewall
Hardware Installation and Reference Guide
Document version: 1.1
Date: October 16, 2024
Copyright © 2024 Ruijie Networks

Advertisement

loading
Need help?

Need help?

Do you have a question about the RG-WALL 1600-Z5100-S and is the answer not in the manual?

Questions and answers

Summary of Contents for Ruijie RG-WALL 1600-Z5100-S

  • Page 1 Ruijie RG-WALL 1600-Z5100-S Cloud-Managed Firewall Hardware Installation and Reference Guide Document version: 1.1 Date: October 16, 2024 Copyright © 2024 Ruijie Networks...
  • Page 2 Unless agreed upon otherwise in the contract, Ruijie Networks does not provide any explicit or implicit statements or warranties regarding the content of this document.
  • Page 3 Preface Intended Audience This document is intended for:  Network engineers  Technical support and servicing engineers  Network administrators Technical Support  Ruijie Networks website: https://www.ruijienetworks.com/  Online support center: https://ruijienetworks.com/support  Case portal: https://caseportal.ruijienetworks.com  Community: https://community.ruijienetworks.com ...
  • Page 4 Signs The signs used in this document are described as follows: Warning An alert that calls attention to important rules and information that if not understood or followed can result in data loss or equipment damage. Caution An alert that calls attention to essential information that if not understood or followed can result in function failure or performance degradation.
  • Page 5 Contents Preface ..............................I 1 Overview ............................1 1.1 Introduction ..........................1 1.2 Package Contents........................1 1.3 Appearance ..........................2 1.3.1 Front Panel ........................2 1.3.2 Rear Panel ........................3 1.4 Specifications ..........................4 1.5 Power Module ..........................5 1.6 Hard Disk ........................... 7 2 Preparing for Installation ........................
  • Page 6 2.2.6 Anti-interference Requirements ................... 13 2.2.7 Lightning Protection Requirements ................13 2.2.8 Installation Site Requirements ..................13 2.3 Tools ............................13 2.4 Unpacking the Device ......................14 3 Installing the Device ......................... 15 3.1 Installation Procedure ......................15 3.2 Preparing for Installation ......................15 3.3 (Optional) Installing the Hard Disk ...................
  • Page 7 5.1.1 Symptom ........................23 5.1.2 Solution ........................23 5.2 Optical Port Fails ........................23 5.2.1 Symptom ........................23 5.2.2 Solution ........................23 6 Appendix A: 10 Gigabit SFP+ Transceivers ..................24 7 Appendix B: Gigabit SFP Transceivers ....................1...
  • Page 8 Overview Introduction The RG-WALL 1600-Z5100-S firewall (Z5100-S firewall or Z5100-S for short) is a next-generation Z series firewall of Ruijie Networks for all industries. With cloud-network linkage, the firewall continuously improves its security detection capabilities and evolves from passive defense to proactive defense based on quick detection and proactive handling.
  • Page 9 Hardware Installation and Reference Guide Overview Appearance 1.3.1 Front Panel Figure 1-1 Front Panel Table 1-2 Components on the Front Panel Component Description MGMT port It is used to access the device management page upon first login. System status LED (SYS) Blinking green: The device is powered on and being initialized, or the system is restoring factory settings.
  • Page 10 Hardware Installation and Reference Guide Overview Component Description Link/ACT status LEDs (square) Solid green: The link on the port is Up. Blinking green: The port is receiving or sending data. of 10/100/1000BASE-T ports Off: No link is established on the port. Speed LEDs (round) of Solid orange: Gbps port speed Off: 100/10 Mbps port speed...
  • Page 11 Hardware Installation and Reference Guide Overview Specifications Table 1-4 Specifications Model RG-WALL 1600-Z5100-S Memory 4 GB DDR4 memory (ECC supported) eMMC 8 GB Hard Disk No hard disk for factory delivery. A 1 TB hard disk drive (HDD) can be added.
  • Page 12 Hardware Installation and Reference Guide Overview Operating humidity: 40% to 65% RH (non-condensing) Humidity Storage humidity: 10% to 90% RH (non-condensing) Warning  In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
  • Page 13 Hardware Installation and Reference Guide Overview Figure 1-3 Appearance of RG-NSEC-PA70I/RG-PA70I Table 1-5 describes LED status of RG-NSEC-PA70I/ RG- PA70I. Table 1-5 Power Module LED Silkscreen Item Status Description Label The power module is not outputting power or an output fault occurs.
  • Page 14 Table 1-6 Power Module Specifications Model RG-NSEC-PA70I/RG-PA70I Firewall Model RG-WALL 1600-Z5100-S Dimensions (W x D x H) 50.5 mm x 156 mm x 38 mm (1.99 in. x 6.14 in. x 1.50 in.) Weight About 0.395 kg (0.871 lbs.) Rated Input Voltage...
  • Page 15 Table 1-7 Hard Disk Specifications Model RG-NSEC-HDD-1T Firewall Model RG-WALL 1600-Z3200-S, RG-WALL 1600-Z5100-S Dimensions (W x D x H) 130 mm x 102 mm x 27 mm (5.12 in. x 4.02 in. x 1.06 in.) Weight 0.300 kg (0.661 lbs.)
  • Page 16 Hardware Installation and Reference Guide Preparing for Installation Preparing for Installation Safety Precautions Note  To avoid personal injury and device damage, carefully read the safety precautions before installation.  The following safety precautions may not cover all possible dangers. 2.1.1 General Safety ...
  • Page 17 Hardware Installation and Reference Guide Preparing for Installation  You are advised to use an uninterrupted power supply (UPS) to avoid interference caused by power failures. 2.1.4 ESD Safety  Properly ground the device and floor.  Keep the indoor installation environment clean and dust-free. ...
  • Page 18 Hardware Installation and Reference Guide Preparing for Installation 2.2.3 Temperature and Humidity Requirements To ensure the normal operation and prolonged service life of the device, maintain an appropriate temperature and humidity in the equipment room. If the device works in an environment with too high or too low temperature and humidity for a long period, it may be damaged.
  • Page 19 Hardware Installation and Reference Guide Preparing for Installation Apart from dust, the salt, acid, and sulfide in the air in the equipment room must meet strict requirements. These harmful substances will accelerate metal corrosion and component aging. Therefore, the equipment room should be properly protected against the intrusion of harmful gases, such as sulfur dioxide, hydrogen sulfide, nitrogen dioxide, and chlorine gas.
  • Page 20 Hardware Installation and Reference Guide Preparing for Installation The grounding resistance should be less than 1 ohm. The grounding terminal on the cabinet should be properly grounded before device running. 2.2.6 Anti-interference Requirements  Take interference prevention measures for the power supply system. ...
  • Page 21 Hardware Installation and Reference Guide Preparing for Installation Note The Z5100-S firewall is delivered without a tool kit. You need to prepare the preceding tools in advance. Unpacking the Device Before installing the Z5100-S firewall, open the accessories box delivered with the product and check whether the accessories are complete.
  • Page 22 Hardware Installation and Reference Guide Installing the Device Installing the Device Caution Before installing the device, ensure that all the requirements specified in Chapter 2 are met. Installation Procedure Install the device according to the following procedure to prevent damage. Preparing for Installation Prepare for installation according to 2 Preparing for Installation...
  • Page 23 Hardware Installation and Reference Guide Installing the Device an accident. (Optional) Installing the Hard Disk Application Scenario If you have purchased a hard disk, follow the instruction described in this section to install the hard disk so as to prevent damage to the hard disk. Precautions The hard disk does not support hot swapping.
  • Page 24 Hardware Installation and Reference Guide Installing the Device Installing the Device at the Specific Position The Z5100-S firewall can be installed in a standard cabinet. If no cabinet is available, the device can be installed on a workbench. 3.4.1 Installing in a Cabinet Application Scenario When a standard cabinet is configured, the fixed accessories delivered with the device can be used.
  • Page 25 Hardware Installation and Reference Guide Installing the Device Follow-up Procedure After installation, check the following items:  The device is securely installed in the cabinet.  About 1 U space is reserved above and below the device to facilitate heat dissipation. ...
  • Page 26 Hardware Installation and Reference Guide Installing the Device Align the M4 end of the grounding cable with the screw hole on the grounding terminal, and fasten the screw. Connect the M6 end of the grounding cable to the grounding terminal of the cabinet or workbench. Follow-up Procedure After connecting the grounding cable, check the following items: ...
  • Page 27 Hardware Installation and Reference Guide Installing the Device device is installed on a workbench, check whether the workbench is sturdy enough to support the combined weight of the device and its accessories. For both installation modes, check whether there is sufficient space for heat dissipation.
  • Page 28 Hardware Installation and Reference Guide Commissioning Commissioning Setting Up the Configuration Environment Prerequisites The Z5100-S firewall provides the default configuration, as described in Table 4-1. Table 4-1 Factory Settings of the Device DHCP By default, the DHCP service is enabled. Login Address Default address: https://192.168.1.200 Account and...
  • Page 29 Hardware Installation and Reference Guide Commissioning (2) Turn on the power switch of the firewall. 4.2.3 Checklist After Power-On Check whether the statuses of LEDs are normal. Table 4-2 LED Statuses After Power-On Normal Status SYS LED Solid green PWR1/PWR0 LED Solid green Configuring the Product Follow-up Procedure...
  • Page 30 (4) Check whether the power cord is securely connected to the power module. If necessary, remove the power module and check its connector. If the problem persists, please contact Ruijie technical support. Optical Port Fails 5.2.1...
  • Page 31 Appendix A: 10 Gigabit SFP+ Transceivers Appendix A: 10 Gigabit SFP+ Transceivers Ruijie Networks provides 10 gigabit SFP+ transceivers according to the port types required for the firewall. You can select a transceiver as required. This document provides models and technical specifications of some 10 gigabit SFP+ transceivers for reference.
  • Page 32 Hardware Installation and Reference Guide Appendix A: 10 Gigabit SFP+ Transceivers Conductor Data Rate Module Connector Cable Support Model Diameter Type Type Length (m) (Gbit/s) (AWG) (Yes/No) Active XG-SFP-AOC3M SFP+ 10.3125 optical cable Active XG-SFP-AOC5M SFP+ 10.3125 optical cable Note You just need to plug both ends of the SFP+ cable module into the corresponding ports of the device separately.
  • Page 33 Appendix B: Gigabit SFP Transceivers Appendix B: Gigabit SFP Transceivers Ruijie Networks provides SFP transceivers (Mini-GBIC transceivers) according to the port types required for the firewall. You can select a transceiver as required. In addition to the following models, the gigabit SFP transceiver Mini-GBIC-GT is also supported.