Advertisement
Quick Links
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Medium Flat Panel Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
MWR
Advertisement
Related Manuals for CHIEF MWR6000B
Summary of Contents for CHIEF MWR6000B
- Page 1 I N S T A L L A T I O N I N S T R U C T I O N S Instrucciones de instalación Istruzioni di installazione Installationsanleitung Installatie-instructies Instruções de Instalação Instructions d´installation Medium Flat Panel Wall Mount Spanish Product Description German Product Description Portuguese Product Description...
- Page 2 WARNING: Failure to provide adequate structural strength Chief® is a registered trademark of Milestone AV Technologies. for the installation of this kit can result in serious personal All rights reserved. injury or damage to equipment! It is the installer’s...
- Page 3 Installation Instructions TOOLS REQUIRED FOR INSTALLATION AND PARTS 5/32" 7/32" A (1) B (2) F (4) E (4) C (1) D (1) G (4) 5/16 x 2-1/2" H (4) .850x.395x.135...
- Page 4 Installation Instructions DIMENSIONS NOTE: CUSTOM INTERFACE BRACKET PRODUCT FEATURES NOT SHOWN. THE CUSTOM INTERFACE WEIGHT CAPACITY 125 Lbs Mounting Pattern BRACKET NEEDED FOR YOUR DISPLAY HEIGHT ADJUSTMENT WILL ADD BETWEEN 1/2" AND 2" IN DEPTH AND MAY AFFECT LOCATION OF DISPLAY ,-15 / 2.5 / 0 ON THE MOUNT.
- Page 5 Installation Instructions Mount Installation WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL 7/32" (Ø 6mm) x4 INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to make sure the structure to which the MWR is being installed is capable of supporting five times the combined weight of the mount and all attachments.
- Page 6 Installation Instructions Mount Lateral Position Adjustment The MWR is designed to allow up to 5" of right or left lateral adjustment after being mounted to the wall. This lateral adjustment can be used to more precisely position where the center of the display is located when installation is complete. To adjust the mounts lateral position: Remove display if installed.
- Page 7 Installation Instructions Cover Installation To install channel covers: Install upper and lower wall channel covers (B) by tipping cover top down and positioning as shown in end view of figure below. (See Figure 5) Tap firmly across bottom of channels (B) to lock in place as shown in figure below.
- Page 8 200 x 200 pattern the mounting buttons can be installed directly to the back of the display. If the display has any other mounting pattern an interface bracket must be obtained before proceeding. Consult a Chief Customer Service Remove pin representative if an interface bracket is required.
- Page 9 Installation Instructions (E) x 4 From Display Figure 8 ADJUSTMENTS Pitch Tension Adjustment To adjust display pitch tension: With display installed, tighten or loosen two screws, one on each side, using a 5/32” hex wrench. (See Figure 9) Check for desired tension. Repeat Steps 1 and 2 until desired tension is obtained.
- Page 10 Installation Instructions Roll Adjustment The MWR allows for the horizontal alignment (Roll)of the (D) x 1 display to be adjusted up to 2° right or left to level the display after installing. (C) x 1 To adjust Roll: Loosen the roll tension adjustment nut located on the back side of the faceplate assembly.
- Page 11 Installation Instructions...
- Page 12 A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands Chief Manufacturing, a products division P +31 (0)40 2668620 of Milestone AV Technologies F +31 (0)40 2668615 Asia Pacific A Office No.
Need help?
Do you have a question about the MWR6000B and is the answer not in the manual?
Questions and answers