Advertisement
Quick Links
Technical manual
Indoor long-range dual technology detector
for intrusion detection systems
1
DESCRIPTION
DT93 is a dual-technology detector.
The device features two sections working in AND mode.
Infrared section (IR): digital PIR sensor with temperature
compensation and lens with white light protection.
Microwave section (MW): 10.525GHz DRO planar antenna
with built-in LNA amplifier.
For side-by-side mounting, differentiated frequencies can
be used.
The detector long range (up to 23 m) makes it suitable to
protect large-size indoor locations.
The device features the anti-blinding, anti-masking, an-
ti-sneak functions.
LEDs indicate device working activity.
DT93 can be set with board dip switch.
Optional joint available.
DT93 is certified IMQ - Security Systems.
DT93
Addressee for this information:
User |
Installer
2
PCB
3
2
1
1
Dip switches
2
PIR sensor
3
Terminal board
4
Blue LED
5
Red LED
6
Green LED
7
Jumper to exclude protection against removal
8
MW antenna
9
Tamper button
1 1 1
4
5
6
7
8
9
Advertisement
Related Manuals for El.Mo DT93
Summary of Contents for El.Mo DT93
- Page 1 The device features the anti-blinding, anti-masking, an- ti-sneak functions. LEDs indicate device working activity. DT93 can be set with board dip switch. Optional joint available. DT93 is certified IMQ - Security Systems. Dip switches PIR sensor...
- Page 2 25 metres between each other. MW vertical coverage 30° ° • In case of installation of DT93 and another detector at a Max power output distance of less than 25 m between each other, one of the General features two must be a differentiated-frequency model.
- Page 3 DEVICE MOUNTING zones on one level Top view • Opening the housing 94° 90° 15 m 10 m – loosen cover fixing screw – insert the screwdriver flat tip between detector bottom and cover in the indicated areas 10 m –...
- Page 4 • Fixing the bracket – remove the sheath from the end of the wires to connect to the terminal block – feed the cable as illustrated – fix the mounting plate to the wall using the supplied screws and inserts (use A holes) 6°...
- Page 5 – fix the joint to the mounting plate using a pan head screw • Base wall mount – rotate the base on the joint as needed – fix the base to the joint using the supplied screw (E) • Wirings Detector terminal board: 12 V ESCL.
- Page 6 Triple-balancing drawing: 1 mm Detector – insert closing screw in hole H, leaving approximately 1 mm between the screw and the housing bottom – lower the device cover until the hooks on the internal cov- er fit into the base slots (I) Control unit Verify the unit supports triple-balancing setup.
- Page 7 ▼ Sensitivity adjustment Anti-blinding function DIP 4 Sensitivity DT93 features anti-blinding function. Minimum: 8 MW pulses, 3 IR pulses The function detects blinding attempts made by placing a Maximum: 4 MW pulses, 2 IR pulses (default) reflective body before the lens. Use dip switches 2 and 3 to activate the function.
- Page 8 Note: for grade 3 compliance, enable anti-masking and an- the LEDs remotely. ti-blinding functions. MAINTENANCE Anti-sneak DT93 features anti-sneak function. Periodic test The function detects attempts to elude the IR section from Carry out a simple test regularly to verify the functionality far off with special physical expedients.
- Page 9 Table of contents DESCRIPTION......P. 1 PCB ........P. 1 TECHNICAL DATA.
- Page 12 The information and product features herein are not binding and may be changed without prior notice. EL.MO. Spa - Via Pontarola, 70 - 35011 Campodarsego (PD) - Italy Ph. +39 049.9203333 - Fax +39 049.9200306 - Help Desk +39 049.9200426 - www.elmospa.com - international@elmospa.com...
Need help?
Do you have a question about the DT93 and is the answer not in the manual?
Questions and answers