Download Print this page

Sunricher SRP-2305N-25CC250-700 Manual

25w dali dt6 nfc enabled led driver(constant current)

Advertisement

Quick Links

25W DALI DT6 NFC Enabled LED Driver(Constant Current)
2
Important: Read All Instructions Prior to Installation
Function introduction
AC/DC power
input
L
N
DA
DA
DALI Dimmable Driver
DALI signal input
AC Push input
Product Data
LED Channel
DC Voltage
Current
Output
Current Accuracy
Rated Power
Voltage Range
Frequency Range
Power Factor (Typ.)
Total Harmonic
Distortion
Efficiency (Typ.)
Input
AC Current (Typ.)
Inrush Current (Typ.)
Leakage Current
Standby Power Consumption
Anti Surge
Dimming Interface
Dimming Range
Control
Dimming Method
Dimming Curve
LED Output
-
1
6-58V
250-700mA via NFC setting; Min.current gear lower to 0.1mA
±3%( ±1%@Certain full load) @ full load
Max. 25W
200-240VAC/176-280VDC
0/50/60Hz
> 0.97 @ 230VAC Full load
THD ≤ 9% (@ full load / 230VAC)
>85% @ 230VAC full load
0.2A @ 230VAC
Max. 5.64A at 230VAC; 72μs duration
< 5mA /230VAC
<0.5W
L-N:2KV
DALI Device Type 6 (DALI consumption < 2mA)/ AC Push
0.01%-100%@ Max current
Amplitude/CCR dimming
Linear/ Logarithmic optional
Short Circuit
Yes, recovers automatically after fault condition is removed
Over Current
Protection
Yes, recovers automatically after fault condition is removed
Over Temperature
Working Temp.
Max. Case Temp.
Environment
Working Humidity
Storage Temp.
& Humidity
Safety Standards
Withstand Voltage
Safety &
Isolation Resistance
EMC
EMC Emission
EMC Immunity
MTBF
Others
Dimension
Warranty
• In compliance with IEC 62386-101:2014, IEC 62386-102:2014, IEC 62386-207 Ed2,
• Built-in DALI-2 interface, DALI DT6 device
• Dimmable LED driver. Max. output power 25W
• 250-700mA current selectable via NFC program tool. Min.current gear lower to 0.1mA
• DALI Address/Group/Scene setting via NFC program tool.
• Class Ⅱ power supply, full isolated plastic case
• High power factor and efficiency
• To switch and dim LED lighting luminaries
• Amplitude/CCR dimming, smooth and deep dimming
• Compatible with universal DALI masters that support DT6 commands
• Error report function
• IP20 rating, suitable for indoor LED lighting applications
• 5 years warranty
Safety & Warnings
• DO NOT install with power applied to the device.
• DO NOT expose the device to moisture.
Operation
With DALI master
1. DALI Address
1 DALI address for 1 channel output are assigned by DALI Master controller automatically, please refer to user
manuals of compatible DALI Masters for specific operations.
Yes, recovers automatically after temperature drop
-25℃ ~ +45℃
TC=85℃ (Ta="45℃")
10% ~ 95% RH non-condensing
-40℃ ~ +80℃, 10% ~ 95% RH
EN61347-1, EN61347-2-13
I/P-O/P: 3.75KVAC
I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH
En55015, EN61000-3-2, EN61000-3-3
En61547, EN61000-4-2,3,4,5,6,8,11
191350H, MIL-HDBK-217F @ 230VAC full load
and 25℃ ambient temperature
120x41x28mm (L*W*H)
5 Years

Advertisement

loading
Need help?

Need help?

Do you have a question about the SRP-2305N-25CC250-700 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sunricher SRP-2305N-25CC250-700

  • Page 1 25W DALI DT6 NFC Enabled LED Driver(Constant Current) Short Circuit Yes, recovers automatically after fault condition is removed Over Current Protection Yes, recovers automatically after fault condition is removed Over Temperature Yes, recovers automatically after temperature drop Important: Read All Instructions Prior to Installation -25℃...
  • Page 2 Step 3: Unlock device, enter parameters configuring page. With NFC Programming devices Note Locked Unlock it 1) Do wiring according to the wiring diagram and power on the DALI system . 2) Recommend setting parameters without power-on the DALI devices . 2) Please make sure your mobile phone has NFC function and enable it .
  • Page 3 Step 5: After setting, please save the selected configuration via NFC and power on the device. 2. With PUSH dimmer DALI Dimmable Driver AC PUSH SWITCH Tips AC Push Function 1) Click the button to switch ON/OFF 1. NFC function doesn’t require any power driver. 2) Press and hold down the button to increase or decrease light intensity to desired level and release it, then repeat the operation 2.
  • Page 4 Output current [A] Dimming Curve MCB Load Quantity Ipeak Twidth Max.quantity of LED Driver per MCB Module Number C16 C20 C25 D10 D16 D20 SRP-2305N-25CC250-700 5.64A 72μs SRP-2309N-25CCT250-700 5.64A 72μs Note: Test data under 700mA gear Note: I (A) 1.Those MCB parameters are based on ABB S200 series circuit breakers.