Sunricher SR-2304B Manual

Waterproof DALI dimmer
2

Important: Read All Instructions Prior to Installation

Function introduction

V+
V-
DA
DA
DALI Controller
Line 1
Brown :V+
Black :V-
Grey White :DA
Blue :DA
Line 2
Brown :V+
Black :V-
Grey White :DA
Blue :DA
PUSH DIM
L DA
N DA
V+
V-
DA
DA

Product Data

Input
Output Output
No. Remarks
Voltage Current Power
4x5A Constant voltage
1 12-36VDC 4x(60-180)W
4x350mA Constant current
2 12-36VDC 4x(4.2-12.6)W
3 4x700mA 4x(8.4-25.2)W
12-36VDC Constant current
• In compliance with IEC 62386-101:2014, IEC 62386-102:2014, IEC 62386-207 Ed2.
• Built-in DALI-2 interface, DALI DT6 device
• Match all DALI systems in the market
• Manual /automatically DALI address setting
• DALI address digital indicate
• Four channels, can set addresses from one to four.
• To work with power repeater to expand output power unlimitedly.
• Waterproof grade:IP67
Safety & Warnings
• DO NOT install with power applied to device.
• This device is IP67 rating and protected against damp environment.

Operation

1.Set DALI Address Manually Via Buttons
1.1. Press and hold down any of the two buttons until numeric digital display flashes, then release the button.
brown cable
DC Power input/output
black cable
yellow+green cable
blue cable
DALI signal input/output
grey white cable
Common Anode Output(+)
CH 1:R output(-)
LED OUTPUT
Brown :V+
Black :R- CH 2:G output(-)
Yellow+Green :G-
Blue :B-
Grey White :W-
CH 3:B output(-)
CH 4:W output(-)
DC Power input/output
DALI signal input/output
DALI Dimming
Size(LxWxH)
Consumption Range
180x73.6x38mm
2mA 0.1%-100%
180x73.6x38mm
2mA 0.1%-100%
2mA 0.1%-100%
180x73.6x38mm
1.2. Click any of the two buttons once to select a digit, click again to change the digit until the desired DALI
70040039
address appears. Click first button to set "tens" position and second button to set "units" position. The address
can be set from 00~63.
1.3. Then press and hold down any of the 2 buttons until the numeric digital display stops flashing to confirm the
setting.
Note: DALI address can be manually assigned from 00-63-FF, by factory defaults, no DALI address is
assigned for the dimmer, and the display shows
dimmer to factory defaults.
2.Set DALI Address Quantity
1.1.
release the button.
1.2.
addresses or 4 addresses.
1.3.
flashing to confirm the setting.
For example, when we set address to 22:
1 2
When select 1A, all four channels will be the same address 22.
When select 2A, channel 1 & 3 will be the same address 22, channel 2 & 4 will be the same
address 23.
When select 3A, channel 1, 2, 3 will be address 22, 23, 24 respectively, and channel 4 address is
also 24.
When select 4A, channel 1, 2, 3, 4 will be address 22, 23, 24, 25 respectively.
3.DALI Address Assigned by DALI Masters
DALI address can also be assigned by DALI Master controller automatically, please refer to user manuals of
compatible DALI Masters for specific operations.
Note: The digital display will show

Wiring Diagram

Ambient
Temperature
-20℃ ~ +50℃
-20℃ ~ +50℃
-20℃ ~ +50℃
DA
DA
Line 1
Brown :V+
Black :V-
Grey White :DA
Blue :DA
Line 2
Brown :V+
Black :V-
Grey White :DA
Blue :DA
PUSH DIM
L DA
N DA
Line 1
Brown :V+
Black :V-
Grey White :DA
Blue :DA
Line 2
Brown :V+
Black :V-
Grey White :DA
Blue :DA
PUSH DIM
L DA
N DA
. Setting DALI address as
Press and hold down both of the two buttons until numeric digital display flashes, then
Click first button to select "1A", "2A", "3A" or "4A" which means 1 address, 2 addresses, 3
Then press and hold down any of the 2 buttons until the numeric digital display stops
When the DALI master is assigning addresses.
L
V+
12V/24V/36V
N
CV PSU
V-
G
DALI
Master
V+
DALI Controller R-
LED OUTPUT
Brown :V+
Black :R-
Yellow+Green :G-
Blue :B-
Grey White :W-
G-
B-
W-
V+
DALI Controller R-
LED OUTPUT
Brown :V+
Black :R-
Yellow+Green :G-
Blue :B-
Grey White :W-
G-
B-
W-
will reset the
AC Power
50/60Hz
V+
R-
G-
B-
W-
V+
R-
G-
B-
W-