Advertisement
Quick Links
NOTE BEFORE INSTALL:
This is a Grille Overlay. Your factory grille components and
other vehicle front end features may be visible once your
new grille is fully installed. To counter this visual element,
we have found that you can hide or mostly eliminate the
components by blacking out with fl at black aerosol spray
paint, plasti-dip or any other similar product. If you choose
to take on this extra modifi cation, you are advised to mask
off any parts or panels that you do not wish to paint over.
T-REX TRUCK PRODUCTS DOES NOT TAKE ON ANY
RESPONSIBILITY FOR THIS ADDITIONAL MODIFICATION.
Parts included
(1) - Bumper Grille Overlay
Polished - Part #25371 OR
Black
- Part #25371B
Hardware included
(2) - 4" x 3/4" Flange Brackets
(2) - #8 (6HD) x 2" Screws
(2) - #8 U-Nuts (Flat Nut Plate)
* Image of Hardware
Tools Required
- Screwdriver Set
- Socket Set
- Flash Light
Page 1
BILLET SERIES Grille
BUMPER grille - #25371 / #25371B
START HERE
PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE INSTALLATION.
Auto makers off er varied models to each vehicle and occasionally manufacture more
than one body style of the same model. To assure your part is correct; our tech
department can be contacted at tech@trexbillet.com to verify fi tment and assist with
technical questions. All other inquires can be directed to info@trexbillet.com. In the
event you do not have internet access please call 1-800-287-5900.
* APPLICATION MODELS VARY. WE RECOMMEND TO VERIFY FITMENT BEFORE BEGINNING INSTALLATION PROCESS.
* IMAGES FEATURED IN THE INSTRUCTION DOCUMENTS MAY NOT ALWAYS EXACTLY MATCH YOUR GRILL / VEHICLE.
DISASSEMBLY
STEP 1
1) Turn off engine and chalk tires
with stop block. Open Hood.
FIG 1
FIG 2
2015 GMC CANYON
Grille Installation Guide
PRO TIP:
Before you begin, use "3M Painters Tape" to apply
a protective guard around the work areas. Attend
to exposed chrome, fender bumper valance. This
will help protect the paint and fi nish of your vehicle.
STEPS 2 - 5
2) Lay out the Billet Bumper.
3) Sort out the provided hardware and
install the (2) 3" screws into the grilles
located tabs.
4) Slide the U-Nut over the Bracket.
5) Thread the assembled bracket w/
U-nuts over the screws. Make sure the
bracket orientation off ers the bent arms
in towards the grille.
SEE FIGURES 1 & 2
Advertisement
Related Manuals for T-Rex 25371B
Summary of Contents for T-Rex 25371B
- Page 1 To assure your part is correct; our tech T-REX TRUCK PRODUCTS DOES NOT TAKE ON ANY department can be contacted at tech@trexbillet.com to verify fi tment and assist with RESPONSIBILITY FOR THIS ADDITIONAL MODIFICATION.
- Page 2 STEP 8 SEE FIGURE 3 8) Place billet overlay into position. Fit into place and examine the gap alignments around all edges and in between the new T-REX Grille and the vehicle components and body lines. FIG 5 STEPS 9 - 10 SEE FIGURE 4 9) Use a Phillips Head screwdriver to tighten screws and secure grille overlay into place.
- Page 3 SEE FIGURES 4 & 5 11) At this point you want to look over your work and examine the gap alignments around all edges and in between the new T-REX Grille and 3) On each side of the front tires, using a flat screwdriver remove plastic clips.
- Page 4 POLISHED FINISH T-REX polished grilles should be waxed at the same time that you wax the vehicle and can be cleaned with soap and water. A polished fi nish can be cared for in the same fashion that would care for your vehicles factory chrome. Never leave wet water spots as that may leave a blemish.
Need help?
Do you have a question about the 25371B and is the answer not in the manual?
Questions and answers