Advertisement
Quick Links
NOTE BEFORE INSTALL:
This is a Grille Overlay. Your factory grille components and
other vehicle front end features may be visible once your new
grille is fully installed. To counter this visual element, we have
found that you can hide or mostly eliminate the components
by blacking out with flat black aerosol spray paint, plasti-dip
or any other similar product. If you choose to take on this
extra modification, you are advised to mask off any parts or
panels that you do not wish to paint over.
T-REX TRUCK PRODUCTS DOES NOT TAKE ON ANY
RESPONSIBILITY FOR THIS ADDITIONAL MODIFICATION.
Parts included
(1) Main Grille Overlay (2-Piece)
Polished - Part #21267 OR
Black
- Part #21267B
(1) T-REX Logo Sticker
Hardware included
(4) 2.5" Threaded Screws
(4) "Toggle Wing" Nuts
(2) #8 Self Tapping Screws
* Image of Hardware
Tools Required
- Screwdriver Set
- Drill w/ screw tip
- Flash Light
Page 1
BILLET SERIES Grille
Main grille - #21267 / #21267B
2015 CHEVROLET COLORADO
START HERE
PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE INSTALLATION.
Auto makers offer varied models to each vehicle and occasionally manufacture more
than one body style of the same model. To assure your part is correct; our tech
department can be contacted at tech@trexbillet.com to verify fitment and assist with
technical questions. All other inquires can be directed to info@trexbillet.com. In the
event you do not have internet access please call 1-800-287-5900.
* APPLICATION MODELS VARY. WE RECOMMEND TO VERIFY FITMENT BEFORE BEGINNING INSTALLATION PROCESS.
* IMAGES FEATURED IN THE INSTRUCTION DOCUMENTS MAY NOT ALWAYS EXACTLY MATCH YOUR GRILL / VEHICLE.
DISASSEMBLY
STEP 1
1) Turn off engine and chalk tires
with stop block. Open Hood.
FIG 1
FIG 2
Grille Installation Guide
PRO TIP:
Before you begin, use "3M Painters Tape" to apply
a protective guard around the work areas. Attend
to exposed chrome, fender bumper valance. This
will help protect the paint and finish of your vehicle.
STEPS 2-4
SEE FIGURE 1 & 2
2) Lay out the 2-piece (Top & Bottom)
3) Sort out the provided hardware and
install the 3" screws into their tabs.
There will be (2) on the top piece and
(2) on the bottom piece.
4) Thread the "Toggle Wing" nuts
over the screws.
Advertisement
Related Manuals for T-Rex BILLET Series
Summary of Contents for T-Rex BILLET Series
- Page 1 To assure your part is correct; our tech T-REX TRUCK PRODUCTS DOES NOT TAKE ON ANY department can be contacted at tech@trexbillet.com to verify fitment and assist with RESPONSIBILITY FOR THIS ADDITIONAL MODIFICATION.
- Page 2 BILLET SERIES Grille Main grille - #21267 / #21267B GRILLE INSTALL - Continued 2015 CHEVROLET COLORADO STEP 5 SEE FIGURE 3 5) See Figure 4 for hardware configured orinetation. SEE FIGURES 4 & 5 STEP 6 6) Place bottom billet overlay into position.
- Page 3 SEE FIGURES 4 & 5 11) At this point you want to look over your work and examine the gap alignments around all edges and in between the new T-REX Grille and 3) On each side of the front tires, using a flat screwdriver remove plastic clips.
- Page 4 POLISHED FINISH T-REX polished grilles should be waxed at the same time that you wax the vehicle and can be cleaned with soap and water. A polished finish can be cared for in the same fashion that would care for your vehicles factory chrome. Never leave wet water spots as that may leave a blemish.