Axiomtek does not make any commitment to update the information in this manual. Axiomtek reserves the right to change or revise this document and/or product at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
◼ When handling boards and components, wear a wrist-grounding strap, available from most electronic component stores. Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co., Ltd. ® Windows is a trademark of Microsoft Corporation. IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Package List ⚫ General Description GOT710A-ELK is used to keep the train driver informed about the status of the train’s functions. Its design allows it to be deployed in environment with an extended temperature (-40°~ 70°C) and it also complies with the EMC, shock and vibration test requirements of European standard EN50155 for railway applications.
GOT710A-ELK User’s Manual Specifications Main CPU Board ⚫ ® ® Intel Atom quad core x6425E 2.0GHz processor onboard ◼ ⚫ System Memory 1 DDR4 SO-DIMM supports up to 32GB memory capacity ◼ ⚫ BIOS American Megatrends Inc. UEFI (Unified Extensible Firmware Interface) BIOS.
Page 9
GOT710A-ELK User’s Manual System Specification ⚫ 10.4” XGA (1024 X 768) LCD ⚫ Projected Capacitive Touch ⚫ IP65, NEMA 4 rugged protection, aluminum front bezel, rest area of enclosure is IP40 rated ⚫ Net Weight ◼ 2.69 kg (5.93 lb) ⚫...
GOT710A-ELK User’s Manual I/O Outlets Please refer to the following illustration for I/O locations of the GOT710A-ELK. GOT71 Function DC for power input with isolated COM2 with isolated (RS-232/422/485) COM1 with isolated (RS-232/422/485) USB 2.0 x 2 Audio (Line out / Mic in)
When you receive the GOT710A-ELK, the bundled package should contain the following items: GOT710A-ELK unit x 1 ⚫ Phoenix Connector x 1 ⚫ M.2 Slot screw M3*4L x2 ⚫ MINIPCIe Slot screw M3*5L x2 ⚫ If you cannot find the package or any items are missing, please contact Axiomtek distributors immediately. Introduction...
Page 14
GOT710A-ELK User’s Manual This page is intentionally left blank. Introduction...
GOT710A-ELK User’s Manual Section 2 Hardware and Installation The GOT710A-ELK provides rich I/O ports and flexible expansions for you to meet different demand. The chapter will show you how to install the hardware. It includes: Open Back Cover ⚫ Serial Ports Interface ⚫...
GOT710A-ELK User’s Manual Installing the M.2 & Mini PCIe Card The GOT710A-ELK provides two Mini card slots for user to install 4G LTE / Wi-Fi / mSATA or GPS cards. This section tells users how to install M.2 & Mini PCIe Card. Please follow the steps below.
Page 17
GOT710A-ELK User’s Manual Insert the M.2 LAN card & Mini card to the slot. Screw it firmly on the slot. Unscrew 4 screws on the back maintain window cover and remove the antenna plug from one antenna hole on the system chassis.
Page 18
GOT710A-ELK User’s Manual Push top cover up with SIM Card slot. Insert a SIM Card device into the socket. Close the top cover and push the top cover down to secure the SIM Card. Hardware and Installation...
GOT710A-ELK User’s Manual Serial Ports Interface This system supports RS-232/422/485 on COM1~COM2 ports. The pin assignments are listed in table below. If you need to adjust these COM ports to work as RS-232/422/485, please refer to BIOS setting in section 3.5.
GOT710A-ELK User’s Manual Ethernet The GOT710A-ELK is equipped with two high performance plug and play Ethernet interfaces with X-coded. Connection can be established by plugging one end of the Ethernet cable into this RJ-45 connector and the other end to a 2.5Gbe hub with isolated.
GOT710A-ELK User’s Manual 2.5.1 Digital I/O Specification This system supports one DIO (6 input and 2 output) with isolated. The pin assignments are listed in table below. Digital Input: Input channels: 6, sink/source type Input voltage: 0 to 30VDC at 25Hz...
GOT710A-ELK User’s Manual 2.5.3 Digital Input Wiring DRY contact Logic level 0: close to ground Logic level 1: open WET contact Logic level 1: +/-3VDC max. Logic level 0: +/- 10VDC min. to +/-30VDC max Hardware and Installation...
GOT710A-ELK User’s Manual 2.5.4 Digital Output Wiring Audio This system supports one Audio (Line out / Mic in). The pin assignments are listed in table below. Definition MIC-IN-JD MIC-IN AUDIO_OUT_L AUDIO_OUT_R FRONT-JD AUDIO_GND Note: pin# 5 is connected and detected the signal of line- out, signal is switching to line-out.
GOT710A-ELK User’s Manual CAN Bus Connector This system supports one CAN Bus. The pin assignments are listed in table below. Definition CAN_HO CAN_LO CAN_GND DC Power Connector The system supports one DC for power input with isolated. The pin assignments are listed in table below.
GOT710A-ELK User’s Manual Hard keys on front bezel (Optional) Hard Keys on front bezel: ⚫ UIC 612-01 compliant ⚫ Keys for pre-defined functions ⚫ Key backlighting: dimmable Front panel hotkeys define NOTE: Keeping pressing one button after 0.8 seconds, the function will be triggered 4 times per seconds repeatedly.
GOT710A-ELK User’s Manual 2.10 LED Indicators LED lights make sure that whether the MCU is working properly and facilitating to debug in the phrase of research and development. It is not necessarily the actual system mounting LED lights. The following table summarizes LED indication of the device:...
Page 28
GOT710A-ELK User’s Manual This page is intentionally left blank. Hardware and Installation...
GOT710A-ELK User’s Manual Section 3 AMI BIOS Setup Utility The AMI UEFI BIOS provides users with a built-in setup program to modify basic system configuration. All configured parameters are stored in a flash chip to save the setup information whenever the power is turned off. This chapter provides users with detailed description about how to set up basic system configuration through the AMI BIOS setup utility.
GOT710A-ELK User’s Manual Menu Bar The top of the screen has a menu bar with the following selections: Menu Bar Description Main To set up the system time/date information. Advanced To set up the advanced BIOS features. H/W Monitor To display current hardware status.
GOT710A-ELK User’s Manual Main Menu When you first enter the setup utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. System Time/Date can be set up as described below.
GOT710A-ELK User’s Manual Advanced Menu The Advanced menu also allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus: F81216 Super IO Configuration ◼...
Page 33
GOT710A-ELK User’s Manual ⚫ F81216 Super IO Configuration Use this screen to select options for the Super IO Configuration and change the value of the selected option. AMI BIOS Setup Utility...
Page 34
GOT710A-ELK User’s Manual Serial Port 1-2 configuration 1. Serial port: This option used to enable or disable the serial port. 2. Device Setting: This item specifies the base I/O port address and Interrupt Request address of serial port. The port 1 Optimal setting is 3F8/IRQ4.
Page 35
GOT710A-ELK User’s Manual ⚫ Hardware Monitor This screen shows the Hardware Health Configuration. AMI BIOS Setup Utility...
Page 36
GOT710A-ELK User’s Manual ⚫ Smart Ignition Configuration Press Enter to access the sub-menu. Calculated based on the 24-hour military-time clock. BIOS menu item Description Ignition Enabled Management Switch to In-Vehicle mode *Note: IGN signal will only be triggered when M12 pin5 IGN is connected to VCC, ignition power or ignition control signal.
Page 37
GOT710A-ELK User’s Manual AMI BIOS Setup Utility...
Page 38
GOT710A-ELK User’s Manual BIOS menu item Description Activate Voltage Trigger The system turns on when the voltage delivered by the power source is higher than the value you set here. Low Voltage Trigger The system will begin the countdown once voltage drops below the value you set here.
Page 39
GOT710A-ELK User’s Manual ⚫ Trusted Computing This sub-menu will allow you to enable/disable Trusted Platform Module (TPM) support and to configure the TPM State. Select Trusted Computing and press Enter to access the sub-menu. Select the Security Device Support item to enable the TPM device.
Page 40
GOT710A-ELK User’s Manual ⚫ CPU Configuration This screen shows the CPU configuration, and you can change the value of the selected option. Intel Virtualization Technology Enable or disable Intel Virtualization Technology. When enabled, a VMM (Virtual Machine Mode) can utilize the additional hardware capabilities.
Page 41
GOT710A-ELK User’s Manual ⚫ Storage Configuration During system boot up, the BIOS automatically detects the presence of SATA devices. In the SATA Configuration menu, you can see all hardware currently installed in SATA ports. SATA Controller(s) Enable or disable the SATA Controller feature. The default is Enabled.
Page 42
GOT710A-ELK User’s Manual ⚫ Memory Configuration Display memory information with inserted the system. AMI BIOS Setup Utility...
Page 43
GOT710A-ELK User’s Manual ⚫ USB Configuration Display all detected USB devices. AMI BIOS Setup Utility...
Page 44
GOT710A-ELK User’s Manual ⚫ Device Configuration You can use this screen to select options for the 8-bit Digital I/O Configuration. A description of the selected item appears on the right side of the screen. For items marked with “”, please press for more options.
Page 45
GOT710A-ELK User’s Manual DIO Modification Enable or disable digital I/O modification. If modification is disabled, the DIO status sub screen is as follows: Once it is enabled, you can load manufacture default and access to the DIO status sub screen to set output or input, see image below.
GOT710A-ELK User’s Manual Chipset Menu System Agent (SA) Configuration This screen shows the memory information. PCH-IO Configuration You can use this screen to select options for the LVDS Configuration. AMI BIOS Setup Utility...
GOT710A-ELK User’s Manual Security Menu The security menu allows users to change the security settings for the system. Administrator Password This item indicates whether an administrator password has been set (installed or uninstalled). User Password This item indicates whether a user password has been set (installed or uninstalled).
Page 48
GOT710A-ELK User’s Manual ⚫ Secure Boot Secure Boot feature is Active if Secure Boot is Enabled, Platform Key (PK) is enrolled and the System is in User mode. The mode change requires platform reset. Secure Boot Mode Secure Boot mode options : Standard or Custom. In Custom mode, Secure Boot Policy variables can be configured by a physically present user without full authentication.
GOT710A-ELK User’s Manual Boot Menu The Boot menu allows users to change boot options of the system. You can select any of the items in the left frame of the screen to go to the sub menus: Setup Prompt Timeout...
GOT710A-ELK User’s Manual Save & Exit Menu The Save & Exit menu allows users to load your system configuration with optimal or fail-safe default values. Save Changes and Exit When you have completed the system configuration changes, select this option to leave Setup and return to Main Menu.
Page 51
GOT710A-ELK User’s Manual Discard Changes Select this option to quit Setup without making any permanent changes to the system configuration. Select Discard Changes from the Save & Exit menu and press <Enter>. Select Yes to discard changes. Restore Defaults It automatically sets all Setup options to a complete set of default settings when you select this option.
Page 52
GOT710A-ELK User’s Manual This page is intentionally left blank. AMI BIOS Setup Utility...
GOT710A-ELK User’s Manual Appendix A Watchdog Timer A.1 About Watchdog Timer After the system stops working for a while, it can be auto reset by the watchdog timer. The integrated watchdog timer can be set up in the system reset mode by program.
Page 54
GOT710A-ELK User’s Manual This page is intentionally left blank. Watchdog Timer...
Page 55
GOT710A-ELK User’s Manual Appendix B Windows Power Button Setting Please enter the power button setting through the PC console, and then follow below steps to complete the setting. Windows Power ButtonSetting...
Page 56
GOT710A-ELK User’s Manual When IGN function has been used, the power button’s setting must be switched to “Shut down” as below. Then the system can be shut down normally, after IGN has been turned off. Windows Power ButtonSetting...
Page 57
GOT710A-ELK User’s Manual Windows Power ButtonSetting...
Page 58
GOT710A-ELK User’s Manual Windows Power ButtonSetting...
Need help?
Do you have a question about the GOT710A-ELK and is the answer not in the manual?
Questions and answers