Advertisement
Note: Remote Control requires 2 × "AAA" batteries (included)
The Majority Teton Plus soundbar will automatically pair to the subwoofer when both items are switched on. The Pair LED on the rear of the subwoofer will flash when searching for connection, then remain static when connected.
The Pair Reset button on the rear of the subwoofer (Ref.15) should not be pressed unless you need to pair with a new subwoofer. If this button is accidentally pressed, the soundbar has a default reset that it will reconnect to the existing subwoofer after 90 seconds.
The Majority Teton Plus will automatically go to standby mode after 180 minutes if the connected TV is switched off, or if there isn't any audio signal in.
The Majority Teton Plus can be mounted to a wall using the appropriate fittings for your wall type by using the wall mounting brackets positioned at the rear of the unit. As these differ between wall types the fittings are not included. To wall mount the Teton soundbar, the appropriate fittings for your application will need to be sourced.
State | Indicator Lights |
Power off | Red |
AUX mode | Green |
USB mode | Purple |
RCA mode | White |
ARC mode | Light blue |
Optical mode | Yellow |
Bluetooth ready | Flashing blue |
Bluetooth connected | Blue |
Indicator | Status |
Flashing slowly | The subwoofer is disconnected |
Flashing rapidly | Soundbar are wireless pairing with Subwoofer |
Stops flashing and shows solid orange light | Wireless paired successfully |
Mode | Bass/Treble Options Db (decibels) refers to sound levels |
MUSIC | Manually change BASS and TREBLE settings (between 0Db and +8Db). |
DIALOG | BASS+ BASS- TRE+ TRE- functions are disabled |
MOVIE | BASS+ BASS- TRE+ TRE- functions disabled |
FLAT | Restore to default settings and manually change BASS and TRE settings between -8Db and +8Db |
The Teton Plus subwoofer should be within 8 meters of the soundbar in an open area. The closer they are located, the better the performance. Do not place anything on the top of the subwoofer.
The soundbar carries most of the dialog, music and movie sound effects. If your TV is on a table or stand, place the soundbar directly in front and centre of the TV.
The subwoofer is designed to produce powerful low bass sound effects. The performance is directly related to its placement within the room, when setting up the Teton Plus, make sure to find the best location for maximum bass performance.
Connect your USB device to the USB port (Ref.9) on the soundbar.
Then press the INPUT button on the remote control (Ref.23) or press the INPUT button on the soundbar (Ref.5) to choose USB mode - the light will change to purple.
Now you will be able to play audios files from the USB device through the soundbar.
Rear Panel of Soundbar
Use the RCA Stereo Audio Cable to connect the TV's stereo RCA(L/R) audio output socket to the RCA(L/R) sockets on the unit (Ref.10).
Then press the INPUT button on the remote control (Ref.23) or press the INPUT button on the soundbar (Ref.5) to choose the AUX function.
Troubleshooting: If you are not receiving a picture or encountering interference, please ensure that the RCA cable is being connected to 'output' RCA ports on your TV set. This will ensure that the sound is being exported correctly.
If your TV does not have 'output' RCA ports, please use an alternative connection method.
Connect the HDMI cable (not included) to the HDMI ARC port on the back of the soundbar (Ref.11) to the HDMI (ARC) connector on the TV.
NOTE: In the HDMI ARC mode, if your speakers have no audio output and the indicator light is flashing quickly, use your source device (such as a TV, CD player, or cable/satellite receiver).The audio output mode is set to PCM, or turn off the sound source output.
The transmission of digital audio signals between devices is not workable for all the TV brands in the markets because the branded TVs are not cross-brand compatibility to each other.
You will need: An audio source with an Optical Audio Output and a Digital Optical Audio cable (included).
Connect the Digital Optical Audio cable to the optical output on the audio source and to the Optical Input on the soundbar (Ref.12).
Press the POWER button on the side panel (Ref.4) or on the remote control (Ref.18) to switch on the unit.
Press the INPUT button on the remote control repeatedly (Ref.23) to switch to Optical mode or press the INPUT button (Ref.5) repeatedly on the soundbar to select Optical mode. The mode indicator LED will turn yellow.
Using the native controls on your connected device, make sure the audio settings are set to PCM or Optical Audio and are switched on.
Audio from the connected audio source will now be played through the speakers.
Plug one end of a 3.5mm audio input cable (included) into the Line in (Ref.7) on the unit. Before use, disconnect any cables connected to the Stereo RCA Inputs. Plug the other end of the cable into the audio output/headphone output on an MP3 player or other audio source.
Press the POWER button on the side panel (Ref.4) or on the remote control (Ref.18) to switch on the unit.
Press the INPUT button repeatedly on the soundbar (Ref.5) or press INPUT on the remote control (Ref.23) repeatedly until LINE in mode is selected. The mode indicator will turn green.
Audio played through the connected device will now be heard through the speakers.
Ensure that the power supply voltage is within the range of 100V~240V. Any other voltage may cause damage to the unit.
Unwind the mains cable to its full length. Connect the mains plug to a mains socket. Ensure that the mains plug is fully inserted into the mains socket. The mains plug/appliance coupler is used as the disconnect device. The disconnect device must remain readily operable.
Connect both adapters into the power port on the soundbar (Ref.13) and subwoofer (Ref.16).
Ensure all audio connections of the unit are connected before connecting to the mains power socket. Unplug the power cord from the outlet when the unit is use for an extended period of time.
Press the POWER button on the soundbar (Ref.4) or on the remote control (Ref.18) to switch on the unit.
Press the INPUT button repeatedly on the remote control (Ref.23) or press the INPUT button on the soundbar (Ref.5) repeatedly until Bluetooth mode is selected (indicated by a flashing blue light).
From your Bluetooth device, select the "Majority Teton" when prompted to choose a Bluetooth device.
If a password is required, enter "0000". If you encounter issues at this stage, please refer to the user manual for your Bluetooth device for instructions on pairing and connecting Bluetooth devices.
When successfully connected, a beep will issue from the unit and a solid blue light will be displayed. After initial pairing, the unit will stay paired unless manually unpaired by the user, or until the device is reset.
If your device should become unpaired or you find it is unable to connect, repeat the above steps.
Note: When the soundbar and subwoofer are wirelessly paired successfully, the units will automatically pair after they are restarted.
If the units can't pair automatically, please repeat the above steps.
Observation | Potential Cause/Solution |
No power/function | Check that the power is switched on at the wall. Check that the power adaptor is properly connected to the power outlet. |
No sound | Check whether the unit is set to MUTE. Check that cables are properly installed. If cables are properly installed, please try connecting to your TV using an alternative cable. Check unit is switched on and in correct mode. |
No sound in Bluetooth mode | Check that your Bluetooth device is paired. Check that you have pressed the PAIR button before pairing. Check whether external device requires password "0000". |
Function disturbance | Switch off and unplug the unit. Leave for 2 minutes and switch on again. If a particular mode is causing problems, please try an alternative connection to your TV such as Optical or Bluetooth. |
Remote control function issues | Check whether the battery needs replacing, and replace if necessary. Check whether there are obstacles blocking the remote sensor. |
No sound when connected and switched to OPTICAL IN mode | Check and ensure the audio setting of the input source (e.g. TV, games console, DVD player, etc) is set to PCM mode while using digital connection (such as Optical, HDMI and COAXIAL). |
Power Supply (Soundbar & Sub) | DC 24V 1.7A |
Frequency Response | 30Hz - 20KHz |
SNR | 75dB |
Separation | 65dB |
Bluetooth | V5.0 |
Soundbar Dimensions (WxHxD) | 81.2 × 9.6 × 10.2cm |
Subwoofer Dimensions (WxHxD) | 15 × 38.2 × 28cm |
Net Weight | 5.92kg |
If you require further assistance with your new soundbar, please contact our support team on the Majority website: www.majority.co.uk/support
The apparatus shall not be exposed to dripping or splashing and no objects filled with liquid, such as vases, shall be places on the apparatus.
Main plug is used to disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the main mains completely, the mains plug should be disconnected from the main socket outlet completely. Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
Please read all instructions carefully before use and keep for future reference.
Risk of electric shock. Do not open
Read all instructions carefully before use and keep for future reference
When servicing, use only identical replacement parts
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the Teton Plus and is the answer not in the manual?
Questions and answers