Panasonic AG-HPX370 Operating Instructions Manual page 24

20 P2 CARD ACCESS LED
This LED indicates the recording and playback status of
each card.
For details, refer to [P2 CARD ACCESS LED and status
of P2 cards] (page 32).
21 GENLOCK IN connector
This connector inputs a reference signal when the
camera unit is gen-locked, or when the time code is
externally locked.
 NOTE
• Supply an HD Y signal (1080/59.94i (50i), 720/59.94P (50P))
or a composite signal (480/59.94i (576/50i)) as input
reference signal. The subcarrier of VIDEO OUT connector
output (composite signal) cannot be externally locked. In
SD mode, the signal will not lock to the HD signal.
22 REMOTE connector
Some functions can be remote controlled when the
remote control unit AJ-RC10G (optional accessory) is
connected to the camera.
For details, refer to [Connecting the AJ-RC10G Remote
Control Unit] (page 109).
Some functions can also be remote controlled when the
AG-EC4G extension control unit (optional accessory) is
connected.
For details, refer to [Connecting the AG-EC4G
Extension Control Unit] (page 109).
23 VIDEO OUT connector
This connector outputs video signals.
• In HD mode, down-converted composite video
signals are output.
• Use the menu option DOWNCON MODE in the
OUTPUT SEL screen to set signal output. (The factory
setting is LETTER BOX.)
24 SD memory card slot
Insert an SD memory card (optional accessory) in this
slot. It is used for recording and loading camera setting
menus or lens files, uploading meta data and recording
proxies (optional).
 NOTE
SD memory card precautions
• Use only SD memory cards that conform to the SD
standard or the SDHC standard in this camera.
• MultiMediaCards (MMC) cannot be used. (Use of such
cards may prevent recording.)
• Be sure to use miniSD/microSD card adapters when
using miniSD/microSD cards with this camera. (Note that
this camera will not operate normally when a miniSD/
microSD adapter is installed without inserting a card. Be
sure to insert a card when an adapter is installed.)
• Use of Panasonic SD memory cards and miniSD/microSD
cards is recommended. Be sure to format such cards in
this camera.
• This camera supports SD memory cards with capacities
between 8 MB to 2 GB, and SDHC memory cards with
capacities up to 32 GB. For proxy (optional) recording,
use SDHC memory cards or 256 MB to 2 GB SD memory
cards labeled "High Speed".
4
• For the latest information not available in the Operating
Instructions, visit the support desk at the following
website.
http://pro-av.panasonic.net/
About SD and SDHC memory cards
• The SDHC memory card is a new standard, established
by the SD Card Association in 2006, for memory cards
with capacities of 2 GB or more.
• The SD logo is a registered trademark.
• MMC (MultiMediaCard) is a registered trademark of
Infineon Technologies AG.
25 BUSY (operation mode display) lamp
This lamp indicates the active status of the SD memory
card. It stays illuminated when the card is active.
 NOTE
Do not remove the card while the lamp is on.
The SD memory card could be damaged.
26 DVCPRO/DV connector
An IEEE1394 standard connector for input and output of
video, audio and data.
For details, refer to [Connections to the DVCPRO/DV
Connector] (page 155).
27 SDI OUT 1 connector
28 SDI OUT 2 connector
• This connector outputs SDI signals.
• Use the menu option SDI SELECT in the OUTPUT
SEL screen to select AUTO, 1080i or 480i (576i). This
connector does not support up-conversion.
It outputs the same signals as SDI OUT 1 connector.
29 SCENE FILE dial
This dial allows you to select and load shooting
conditions from the scene files prerecorded to each of
the six positions.
For details, refer to [How to use Scene File Data]
(page 91).
 NOTE
During recording, selecting a position with a different
frame rate will not change the frame rate until the camera
is set to recording standby mode.
30 FOCUS ASSIST button
Turns magnification of the center portion of the image
on and off.
For details, refer to [Focus assist function] (page 84).
31 REC switch
Switches functions of the REC button on the handle.
ON: Enables the REC button.
OFF: Disables the REC button.
32 USB lamp
This lamp lights when the camera is in USB mode (PC
mode).