Safety Warning; Caution For Safety; Biological Risk; Electric Shock And Fire Safety Precautions - CellaVision RAL SmearBox Service Manual

1 PRECAUTIONS
In order to prevent the equipment from accidents and damages, carefully read the precautions
listed below before servicing the product and follow them closely.

1.1 Safety warning

This product is supplied through a power supply that delivers low voltage. However, usual
safety measures must be handled during servicing this product. Use only RAL Diagnostics
replacements parts. Do not make any unauthorized changes or additions to the product as
these may cause the product to malfunctions and create electric shocks or fire hazards.

1.2 Caution for safety

1.2.1 Biological risk

RAL SmearBox is designed to be safe to operate and maintain. However, service personal
®
should be aware of the potential sources of danger particularly in using consumables.
It is strongly recommended to read carefully user guide and how to manage the situation in
case of exposure.
Consider all Specimens, Reagents, Calibrators, Controls, etc... that contain
human blood or serum as potentially infectious! Use established right laboratory
working practices when handling specimens. Wear protective gloves, Lab
coats, Safety glasses and/or Face shields, and follow other biosafety practices
as specified in OSHA Blood borne Pathogens Rule (29 CFR part 1910. 1030) or
equivalent bio-safety procedures.
Please also refer to the W.H.O (World Health Organization) guidelines:
"Laboratory Biosafety Manual, 3rd edition", for further information.

1.2.2 Electric shock and fire safety precautions

Failure in following the instructions below may cause electric shock or potentially cause fire.
• Use only the correct voltage (electric validated voltage network), failure to meet so may
damage the product and potentially cause fire or electric shock.
• Use only the power cable supplied with the product. Use of an unspecified cable may
cause the cable to overheat and potentially cause fire.
• Do not overload the power socket, this could cause the overheating of cables inside the
walls and could lead to fire.
• Do not allow water or other liquids to spill on the product. Do not allow paper clips,
pins or other foreign objects to fall into the product, these may cause a short circuit leading to
REF.: 22019-V07
Revised: 2022-04-07
1 Introduction
an electric shock.
•
shock. When servicing the product, unplug the power cable from the wall socket.
•
grip it firmly and pull. The power cord must be inserted completely; otherwise a poor contact
may cause overheating leading to fire.
•
power cable may be damaged. Do not place objects on top of the power cable. If the power
cable is damaged, it could overheat and cause fire. Exposed cables may cause an electric
shock. Replace the damaged power cable immediately (use only RAL DIAGNOSTICS referenced
and conform power cords), do not reuse or repair the damaged cable. Some chemicals may
attack the coating on the power cable, weakening the cover or exposing cables causing fire
and shock risks.
•
such defects should be repaired immediately. Pay attention not to cut or damage the power
cable or plugs when moving the machine.
•
machine to be disconnected from the power source when such weather conditions are
expected. Do not touch the machine or the power cord if it is still connected to the wall socket
in these weather conditions.
•
set the machine near a humidifier or in front of an air conditioner. Moisture and dust built up
inside the machine may lead to overheating, and cause parts to rust.
•
the product, possibly leading to the product's failing in working properly.

1.2.3 Handling precautions

The following instructions are for your own personal safety to avoid injury, as well as not to
damage the product.
•
support its weight. Failure in doing so may cause the product to be wobbly or to fall down.
•
•
close to the product that may get into the machine if they are spilled, and cause damage or
shock or else fire hazard.
•
window or close to a humidifier or heater. Damages may be caused to the product in such
8 9
Never touch the plugs or tip of the power cable with wet hands, this may cause electric
Be careful when inserting or removing the power cord. When removing the power cord,
Beware of the power cable. Do not leave it twisted, bent sharply around corners or
Ensure that the power sockets and plugs are not cracked or broken in any way. Any
Beware during thunder or lightning storms. RAL DIAGNOSTICS recommends this
Avoid damp or dusty areas; install the product in a clean well ventilated place. Do not
Do not set the product in direct sunlight. This would cause a rise of temperature inside
Ensure yourself that the product is installed on a level and stable surface, able to
Pay great attention to ensure that your fingers won't be caught or pinched in the device.
Do not place any small metal objects, containers of water, chemicals or other liquids
Do not install the machine in areas with high dust or moisture levels, beside an open
1 Introduction
REF.: 22019-V07
Revised: 2022-04-07