Specifications And Options; I Specifications; I Options - Icom IC-M710RT Instruction Manual

I Specifications
GENERAL
• Frequency coverage:
Receive 500 kHz–29.999 MHz
Transmit 1.6– 27.5 MHz
• Mode: J3E (USB/LSB), H3E, J2B (AFSK), F1B (FSK),
R3E, A1A (CW);
available modes differ with version
• Number of channels: 1136 channels (max.)
160 user programmable, 242 ITU
SSB duplex, 72 ITU SSB simplex,
662 ITU FSK duplex
• Antenna impedance: 50 Ω nominal
• Usable temp. range: –30°C to +60°C (–22°F to +140°F)
• Frequency stability
(–20°C to +60°C)
0.5–14.9999 MHz
15–29.9999 MHz
• Power supply requirement: 13.6 V DC±15%
• Maximum current drain
(at 13.8 V DC)
Main unit 30 A
(transmit at max. power)
Controller 1.2 A
(receive at max. audio)
• Dimensions
(projections not included)
Main unit 292(W)×117(H)×317(D) mm
1
11 ⁄ (W)×4
2
Controller 292(W)×116(H)×66(D) mm
1
11 ⁄ (W)×4
2
• Weight:
Main unit 7.45 kg; 16 lb 7 oz
(7.65 kg; 16 lb 14 oz GMDSS version)
Controller 1.2 kg; 2 lb 12 oz

I Options

GM-110DSC DSC TERMINAL UNIT
6 channel emergency scanning receiver for distress calls, se-
lective calls, etc. Distress switch box attached.
AT-130/E AUTOMATIC ANTENNA TUNER
Matches the transceiver to a long wire antenna with a mini-
mum of insertion loss.
OPC-566 SHIELDED CONTROL CABLE
Shielded control canble helps protect the transceiver from
RF feedback and extends separation between tuner and
transceiver up to 10 m.
MN-100 ANTENNA MATCHER
Matches the transceiver to a dipole antenna. Covers all HF
bands from 1.5 to 30 MHz. 8 m × 2 antenna wires come at-
tached.
MN-100L ANTENNA MATCHER
Matches the transceiver to a dipole antenna. Covers all HF
bands from 1.5 to 30 MHz. 15 m × 1 antenna wire comes at-
tached.
AH-710 FOLDED DIPOLE ANTENNA
Covers from 1.9 to 30 MHz band. Has an SO-239 connec-
tor. Easy to assemble (non-kink construction).
PS-60 DC POWER SUPPLY
Provides 13.6 V DC (30 A) output from an AC outlet.
PS-65/66 DC-DC CONVERTER
Provides 13.6 V DC (30 A) output from a 10.5–16 V (PS-65)
or 19–32 V (PS-66) DC power source.
OPTIONS AND SPECIFICATIONS
:
±10 Hz
±20 Hz
(GMDSS ±10 Hz)
(negative and floating grounds
available depending on version)
:
:
19 15
⁄ (H)×12 ⁄ (D) in
32 16
9 19
⁄ (H)×2 ⁄ (D) in
16 32
(negative ground)
TRANSMITTER
• Output power:
Below 25 MHz 150/60/20*
125 W PEP
Above 25 MHz 60/20*
85 W PEP
1 2
* Except for Europe versions. *
sions is provided by the AT-130/E antenna tuner.
• Spurious emissions: –65 dB
• Carrier suppression: 40 dB
• Unwanted sideband suppression: 55 dB
• Microphone impedance: 600 Ω
RECEIVER
• Sensitivity
J3E, R3E, J2B, A1A, F1B
(for 12 dB SINAD)
H3E
(for 10 dB S/N)
• Spurious response rejection ration:
(1.6–29.9999 MHz)
• Audio output power:
• Audio output impedance: 4 to 8 Ω
• Clarity variable range: ±150 Hz
All stated specifications are subject to change without notice
or obligation.
RC-21 CONTROLLER UNIT
Additional controller unit allows intercom function. Up to 2
controller unit can be connected.
HS-50 HANDSET
Provides better audio reception during offshore conditions
and comes in handy for listening privacy on board.
HM-120 HAND MICROPHONE
Same as supplied with some versions of the IC-M710RT.
FL-100 CW/FSK NARROW FILTER
Allows better receiver selectivity for CW and FSK.
Bandwidth: 500 Hz/–6 dB
Not necessary with GMDSS versions.
UT-95 2-TONE ALARM UNIT
Provides an alarm transmission for emergency use during
maritime operation. Built-in to marine and GMDSS versions.
OPC-772 SEPARATION CABLE
For extending the separation between the controller and
main unit. Cable length: 20 m (67.4 ft).
RS-M710RT REMOTE CONTROL SOFTWARE
Controls the IC-M710RT from your PC. Microsoft® Win-
dows® 95 only.
MB-70 FLUSH MOUNT KIT
For mounting a controller or the RC-21 to a panel.
9
1
W PEP
2
(GMDSS only* )
1
W PEP
2
(GMDSS only* )
The output power of GMDSS ver-
–60 dB
(USA); (Europe)
:
6.3 µV
(0.5–1.5999 MHz)
1.0 µV
(1.6–1.7999 MHz)
0.5 µV
(1.8–29.9999 MHz)
32 µV
(0.5–1.5999 MHz)
6.3 µV
(1.6–1.7999 MHz)
3.2 µV
(1.8–19.9999 MHz)
More than 70 dB
4.5 W
(at 10% distortion with
a 4 Ω load)
27