Nice E EDGE XSI 0820 DC Instructions And Warnings For Installation And Use
Tubular motor
Hide thumbs
Also See for E EDGE XSI 0820 DC:
Related Manuals for Nice E EDGE XSI 0820 DC
Summary of Contents for Nice E EDGE XSI 0820 DC
- Page 1 Nice E EDGE XSI 0628 DC E EDGE XSI 0820 DC Tubular Motor EN - Instructions and warnings for installation and use...
-
Page 2: Installation Warnings
GENERAL WARNINGS: SAFETY - INSTALLATION - USE (original instructions in Italian) ATTENTION Important safety instructions. Follow all instructions as improper installation may cause serious damage ATTENTION Important safety instructions. It is important for you to comply with these instructions for your own and other people’s safety. -
Page 3: Product Description And Intended Use
• it has a built-in radio receiver and control unit with encoder technology that elec- tronically controls the movement and precision of the limit switches; • it is compatible with all Nice control electronics using the NRC radio system (climate sensors and transmitters);... -
Page 4: Installation Of Accessories
(fig. 3-b), motor bracket (fig. 3-f), or to select supplementary cables (of dif- itations on use ferent lengths), refer to the “Nice Screen” catalogue, which is also available on www. niceforyou.com. • Check the condition of the product right after unpacking it. - Page 5 Gear wheel for limit switch (not included in Drive wheel the package). (not included in the package). 2 screws: self-tapping without point, for plastic 10 mm materials. Diameter: 3,5 mm; length of threaded part: = min. 5 mm - max 8 mm Motor bracket (not included in the package).
-
Page 6: Programming And Adjustments
(connect the white-black cables of all motors together as well as the white-orange cables of all motors). • To select transmitter compatible with the motor’s receiver, refer to the “Nice • Wireless accessories: Screen” catalogue, which is also available on www.niceforyou.com. -
Page 7: Ce Declaration Of Conformity
(*) Note – If you wish to program the “movement duration”, run the procedure in Model / Type: E EDGE XSI 0628 DC, E EDGE XSI 0820 DC question (A.14) only after having programmed the limit switches. -
Page 8: Notes And Warnings
–– GROUP “A” PROCEDURES –– Procedures which can only be completed with a Nice “ERA P” or “ERA W” transmitter with the s, n, t, PRG, ESC keys GENERAL WARNINGS RELATING TO THE PROCEDURES OF PROGRAMMING • Before starting any programming, move the awning to an intermediate position, away from the Up and Down limit switches. - Page 9 A.2 - Temporarily deactivating (and reactivating) motors you do not wish to program NOTES AND WARNINGS • This procedure temporarily deactivates (for 5 minutes) only motors whose up and down limit switches have already been programmed. A.2.1 - To temporarily deactivate motors you do not wish to program = 5 sec The system locks out only those motors whose limit “...
- Page 10 A.3.2 - To program the DOWN limit switch (“1”) continues (x 1) = 5 sec Command an DOWN movement release it after 5 Press and release count 2 movements. Hold down the but- count 2 movements. Hold down the button and wait... the button (1 time);...
- Page 11 “PRG” and “ESC” buttons (like “ERA P” and “ERA W” transmitters). • To run procedures A.6.1.B and A.6.2.B you must have a new transmitter to memorise, chosen from the “Nice Screen” catalogue , and an old previously memorised transmitter.
- Page 12 (x 1) = 5 sec On the NEW transmitter: hold down release it after 5 count 2 movements. On the OLD transmitter: press and count 3 movements (= transmitter the button and seconds; release the button (1 time); memorised). If the system makes 6 movements (= memory locked or full, transmitter not memorised).
- Page 13 A.7 - Memorisation of a climate sensor connected via radio NOTES AND WARNINGS • To run this procedure you need the climate sensor you want to memorise, chosen from the “Nice Screen” catalogue, and an old transmitter memorised in Mode I (see par. 4.4.1-A).
- Page 14 (x 1) Select one of the following potions and execute it: • option A – delete the motor’s ENTIRE memory. • option B – delete ALL memorised transmitters. • option C – delete ONE memorised transmitter. • option D – delete ALL positions (“0”, “1”, “H”, etc.). Caution! – This deletion must be performed only when you want to reprogram all the positions, using a different procedure than the one used previously (e.g.
- Page 15 TYPE A • To start a movement: to raise the awning press s; to lower it press t. – standard Nice operation for “ERA” • To stop the movement: press the opposite button from that used to start the movement.
- Page 16 A.10 - Programming the motor’s sensitivity to obstacles NOTES AND WARNINGS • Use this procedure to activate or deactivate the safety system that: a) detects the presence of an obstacle along the travel of the awning; b) reduces the motor ten- sion on the awning when it is stationary at the Upper limit switch “0”...
- Page 17 = 5 sec = 5 sec Hold down the but- release it after 5 count 3 movements. Hold down the but- release it after 5 count 5 movements. seconds; seconds; tonand tonand GENERAL INFORMATION ABOUT PROCEDURES “A.12”, “A.13”, “A.14” The “Cruise speed” (procedure A.12), “Acceleration/deceleration of the movement” (procedure A.13) and “Movement dura- tion ”...
- Page 18 4 = 5 sec sec. After about 7 seconds, the motor performs a num- Hold down the buttonand release it after 5 seconds; count 3 movements. ber of movements equal to the number of pulses entered. A.13 - Adjusting the acceleration (at the start of the awning movement) and deceleration (towards the end of the movement) NOTES AND WARNINGS •...
- Page 19 continues 5 OPTIONS: (x ...) 1 press = sets 7 seconds Select the desired op- 2 presses = sets 15 seconds tion and program it as 3 presses = sets 20 seconds follows 4 presses = sets 30 seconds 5 presses = deactivates the function and sets nominal speed Press and release the button the number of times indicated in the option you have chosen;...
- Page 20 A.16 - Locking and unlocking the motor’s memory NOTES AND WARNINGS • Locking the motor’s memory stops any other (unscheduled or unauthorised) transmitters being memorised in it. 4 (x 1) (x 1) (x 1) Press and release count 2 movements. Press and release count 2 movements.
- Page 21 NOTES AND WARNINGS • To run the procedures in this group, you must use a compatible programmer (see the “Nice Screen” catalogue, also available on www.niceforyou.com). • For the programming and adjustment procedures possible with a given programmer, see the programmer’s user manual and interface.
- Page 22 The programming with the “NFC” technology is not yet available on this motor. For more information contact the Nice Technical Assistance. Using a smartphone equipped with NFC technology and a software application produced by Nice (to be installed on your smartphone), you can configure the motors before installing them, even without the need to supply power.
- Page 23 (low speed) or more quickly. the beginning of this condition the motor autonomously performs a down move- If you use a Nice transmitter with “slider” surface (e.g. P1V, etc.) you can vary the ment. speed of the awning as follows: the centre of the slider calls up the speed (100%) set •...
-
Page 24: Green Led
Note: • All technical specifications stated herein refer to an ambient temperature of 2 movements position still to be programmed. 20° C (± 5° C). • Nice S.p.A. reserves the right to apply modifications to products at any time when deemed necessary, maintaining the same intended use and func- 5 movements = serious motor memory error. - Page 26 Nice SpA Via Pezza Alta, 13 31046 Oderzo TV Italy www.niceforyou.com info@niceforyou.com...
Need help?
Do you have a question about the E EDGE XSI 0820 DC and is the answer not in the manual?
Questions and answers