1. Manuals
  2. Brands
  3. El.Mo Manuals
  4. Security Sensors
  5. CONDOR2K
  6. Technical manual

El.Mo CONDOR2K Technical Manual

Indoor wireless dt detector for ng-trx intrusion detection systems
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Technical manual
CONDOR2K
Indoor wireless DT detector for NG-TRX
intrusion detection systems
1
DESCRIPTION
CONDOR2K is a passive infrared wireless detector.
The device features two section working in AND mode.
Infrared section (IR): digital PIR sensor with temperature
compensation and lens with white light protection.
Microwave section (MW): 24 GHz DRO planar antenna.
LEDs indicate device working activity.
CONDOR2K can be programmed using BrowserOne
software.
Optional joint available.
CONDOR2K is compatible with Villeggio NG-TRX, Pregio
and Proxima series control units. Connection to Pregio and
Proxima control units requires use of GATEWAY2K.
Compatible control unit
VILLEGGIO NG-TRX Series
PREGIO Series
PROXIMA series
CONDOR2K is certified IMQ - Security Systems.
Addressee for this information:
Firmware Version
8.2.0 or above
2.3.0 or above
1.0.2 or above
User |
Installer
2
PCB
4
3
2
1
1
PIR sensor
2
Battery position
3
Buzzer (on the rear panel)
4
Tamper button
5
J2 Battery connector
6
MW antenna
7
Learning button
8
Blue LED
9
Red LED
10 Green LED
1 1 1
5
6
7
8
9
10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CONDOR2K and is the answer not in the manual?

Questions and answers

Related Manuals for El.Mo CONDOR2K

Summary of Contents for El.Mo CONDOR2K

  • Page 1 Addressee for this information: User | Installer DESCRIPTION CONDOR2K is a passive infrared wireless detector. The device features two section working in AND mode. Infrared section (IR): digital PIR sensor with temperature compensation and lens with white light protection. Microwave section (MW): 24 GHz DRO planar antenna.

  • Page 2: Technical Data

    TECHNICAL DATA Model CONDOR2K Protection class IP3X Model CONDOR2K IMQ certified EN 50131-2-4: Identification grade 2; EN 50131-5-3 (4) Technology Environmental class Coverage type Volumetric Dimensions and weight W65 × H111 × IR section D48 mm, 125g PIR sensors number...

  • Page 3: Environment Limits

    4.2 Environment limits The use of some building materials may reduce the detector wireless signal strength. Example: • plywood and honeycomb walls: 90-100% of full strength; • solid / hollow brick walls 65-95% of full strength; • concrete walls or metal sheet and plaster: 0-70% of full strength.

  • Page 4: Protection Against Removal For Corner Mount

    – remove the board from the lower hook (D) – hook the cover to base stops again – fix the cover with the screw • Base wall mount Protection against removal for corner mount – using a screwdriver, open the 4 pre-drilled areas of the In case of corner mount, in order to ensure protection support suitable for flat mount (F) or corner (G) mount against removal from wall, move H lever (acting on the mi-...

  • Page 5: Lens Replacement

    5.2 Lens replacement To replace the lens, follow this procedure. Following images show the internal side of the detector cover. • Lens removal – unhook side slots – remove the protective cap – remove LEDs guide and keep it in a safe place –...

  • Page 6: Starting The Device

    OK to go to setup menu STARTING THE DEVICE – use arrow keys ↑ or ↓ to go to LEARN RADIO DET. option – press OK First power up – use arrow keys to go to the zone to which learn the device –...

  • Page 7: Condor2K Detector Options

    CONDOR2K detector options Select Enable detection RF interference to allow the control unit to detect any interference on the three radio Use this section to set specific parameters of CONDOR2K channels. device. For further information about this option and other in this ▼...

  • Page 8: Operating Mode

    OPERATING MODE Condition Red LED Green LED Blue LED Operating Alarm Blinking The detector detects motion inside the covered area. transmission Send tamper Blinking Operating sequence PIR fault Blinking 1. Stabilisation After power on, the device takes around 25 s to stabilize. MAINTENANCE 2.
  • Page 9 compatible receiving device. Discharged batteries shall be disposed of according to cur- rent laws and using specific containers. Materials used are very harmful and polluting if dispersed in the environment.

  • Page 10: Table Of Contents

    NG-TRX options ......p. 6 CONDOR2K detector options ....p. 7 Options for communication to control unit.

  • Page 12: Eu Declaration Of Conformity

    The information and product features herein are not binding and may be changed without prior notice. EL.MO. Spa | Via Pontarola, 70 | 35011 Campodarsego (PD) - Italy Ph. +39 049.9203333 | Fax +39 049.9200306 | Help Desk +39 049.9200426 | www.elmospa.com | international@elmospa.com...

Table of Contents