Download Print this page
Lockly Zeno Series Installation Manual

Lockly Zeno Series Installation Manual

Biometric deadbolt visage smart lock
Hide thumbs Also See for Zeno Series:

Advertisement

Quick Links

PGK728WRHK
VISAGE
BIOMETRIC DEADBOLT
SMART LOCK
Zeno Series
TM
INSTALLATION GUIDE

Advertisement

loading
Need help?

Need help?

Do you have a question about the Zeno Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Lockly Zeno Series

  • Page 1 PGK728WRHK VISAGE BIOMETRIC DEADBOLT SMART LOCK Zeno Series INSTALLATION GUIDE...
  • Page 2 Sensor Magnet Foam Pads Strike Plate ST5*70mm Screw Strike Reinforcer Strike Plate Keys Activation Card (Optional) Activation Card 1 2 3 4 LOCK SERIAL 5 6 7 8 PGK7SK0123456789 (Optional) ACTIVATION CODE 82405798 Need help? Email: help@Lockly.com | Support: +1(669) 500-8835...
  • Page 3 Phillips Screwdriver Flathead Screwdriver Tape measure or ruler Before installing and setting up Lockly Visage, it is important to charge the lithium battery for a full 12 hours. A sufficiently charged battery is necessary to establish connection between the lock and the app.
  • Page 4 Step 1 ADJUST DEADBOLT AND INSTALL The deadbolt defaults to 2-3/8"(60mm) backset which is measured from the centre of the door hole to the door edge. If the deadbolt slot is aligned to the centre of the door hole, skip this step of adjusting deadbolt and proceed to installing deadbolt onto 2-3/4"...
  • Page 5 Step 2 INSTALLING EXTERIOR ASSEMBLY (B) Check the exterior assembly for alignment between door hole and deadbolt. Make sure torque blade is in the vertical position with the deadbolt extended. Place assembly and torque blade through the deadbolt slot and guide connection cables through the cross-bore hole under the deadbolt as shown.
  • Page 6 Step 3 INSTALLING INTERIOR ASSEMBLY (C) Align and secure mounting plate. Guide connection cables through the hole and secure to the lower left notched hole. Select D1/D2/D3 screws based on the door thickness, insert and tighten 2x D screws on the left and right sides of the blade by hand. Check the alignment and insert screws through the circular holes on both sides of the deadbolt torque blade, aligning them with the screw holes on the exterior assembly.
  • Page 7 Step 4 INSTALLING INTERIOR ASSEMBLY (E) Plug the larger cable coming through mounting plate into the interior assembly as shown. Plug cable heads shown. Plug into , match the grey side of the plug. Then Insert the antenna connector into the slot as shown.
  • Page 8 Align torque blade with thumbturn shaft, make sure both are in the vertical position. Insert the connec- tor and excess wire into door hole. Place the interior assembly against Before placing the interior the mounting plate and make sure assembly onto the mounting the torque blade is inserted to the plate, ensure the thumbturn thumbturn shaft.
  • Page 9: Installing Battery

    INSTALLING BATTERY Step 5 With door open and deadbolt fully extended, insert lithium battery. Make sure to hook the battery securely on the provided slot of the interior assembly. 5.2 After the battery is secured, HOLD the program button for 4 seconds. The lock will automatical- ly start self-check (release program button once self-check starts).
  • Page 10 Step 6 INSTALLING STRIKE PLATE Use the included door strike plate or your existing one as long as deadbolt operates smoothly without binding or catching. (Optional) (4X) Strike reinforcer cannot be installed with strike plate Select strike plate according to door frame size. If you need to install strike reinforcer , you may need to increase the depth of the groove to fit into the door frame.
  • Page 11 Step 7 INSTALLING THE DOOR SENSOR Door sensors provide real-time door condition status, such as verify if the door is securely closed. It also sends push notifications to your phone whenever your door opens and enables voice control with Siri, Amazon Alexa or Google assistant. Make sure you install the Door Sensor indoors on a clean and dry surface.
  • Page 12 Step 7 INSTALLING THE DOOR SENSOR WIRED SENSOR ( I ) Install on door interior. If necessary, trim tab from sensor for doors with 2-3/8" (60mm) backset. Clean surface of door and door frame, remove film from adhesive, attach and secure close to door edge as shown. 2-3/4"...
  • Page 13 Step 8 DOWNLOAD LOCKLY APP Download the Lockly app on your smartphone. It is required to finish setup and to establish the connection between the lock, Wi-Fi and the app. Additionally, you'll need the Activation Card with unique pre-paired QR code to your lock.
  • Page 14 The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. , and any use of such marks by Lockly is under license. Other trademarks and trade names are those of their respective owners. Google, Android, Google Play and Google Home are trademarks of Google LLC. , Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc., or its affiliates.

This manual is also suitable for:

Visage