Advertisement
Quick Links
Advertisement
Related Manuals for Lockly 6S
Summary of Contents for Lockly 6S
- Page 1 MODEL 6S INSTALLATION GUIDE LATCH EDITION...
- Page 2 Go to LOCKLY.com/installation to watch a video version of this installation guide. Download the BILT app from the App Store or on Google Play for step-by-step interactive 3-D walk-through installation instructions.
- Page 3 LOCKLY up and running. Installation generally takes less than 30 minutes. If you have any questions please reference our online support at: LOCKLY.com/support or call (669) 500-8835 for help. Reference installation parts overview foldout on back page...
- Page 4 Preparation To complete the installation you will need: Flathead Screwdriver Tape measure or ruler Phillips Screwdriver Pliers Screwdriver with drill bits （Optional） Drilling is not required to install the lock, and is optional. However if you are installing your lock on a brand new door, a drill is required if there are no holes prepared for lock installation.
-
Page 5: Important Notice
Preparation Remove existing door hardware, latch or deadbolts before installing the new lock. Use provided template to bore new holes if needed. " - 2" (35mm - 50mm) Measure and confirm your door is between 1 " - 2" ( 35mm - 50mm). Measure and confirm the hole in the door is 2 "... - Page 6 Step 1 INSTALLING THE LOCKSET Measure the distance between center of front door hole to the edge of your door. Push the shaft (a) to adjust the lockset to 2-3/8"(60mm) or 2-3/4"(70mm). 2-3/8" (60mm) 2-3/4" (70mm) Facing the door exterior, install the lockset according to the opening direction of your door. Out-swing Door In-swing Door Secure lockset with provided...
- Page 7 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued Determine right swing or left swing door While facing the door from the inside, if hinges are on the right side you have the right swinging door. If hinges on the left side you have a left swinging door. The lock ships set for right swing doors.
- Page 8 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued Confirm that your installation was Check that your handle works complete by checking if the pins smoothly by giving it a turn up are flush against the handle, and and down.
- Page 9 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued Changing the Interior Handle Orientation Remove handle retaining screw by turning counter-clockwise. Remove handle and rotate 180° as shown. Return handle retaining screw and secure by turning opposite direction (clockwise).
- Page 10 Step 3 PREPARING LOCK FOR INSTALLATION If you drilled a hole in Preparation, use Slotted Barrel Extension and securely tighten with a flat head screwdriver by turning it clockwise onto the lock. If you did not drill a hole in Preparation, you can leave this pole removed.
- Page 11 Step 4 INSTALLING THE LOCK (EXTERIOR) Exterior Install the exterior lock as shown to the left by aligning the lock straight and passing the cable and attached rods through the lockset. Align the lock straight and press hard (if you use the Adhesive tape in step 3.4) to secure the top of the lock.
- Page 12 Step 5 INSTALLING THE LOCK (INTERIOR) Insert Positioning Rods into the holes to the left and right of the Spindle The holes are located at the 3 o’clock and 9 o’clock positions. Interior Mounting Plate will go against the interior side of your door. Remove the paper layer off of the Adhesive Tape and align the...
- Page 13 Step 5 INSTALLING THE LOCK (INTERIOR) continued Secure top with Pull the cable from the lock exterior through the rectangular hole underneath the positioning rods and spindle. Secure the hole above the spindle with screws Remove the position rods and replace them with screws Tighten clockwise until the mounting plate is secure.
- Page 14 Step 5 INSTALLING THE LOCK (INTERIOR) continued Plug cable that is coming through the door into the lock interior . Match red side of the plug with red on socket - insert tightly. NOTE: If you need to disconnect the cable, make sure to press the snap tab to release the plug before carefully pulling it out.
- Page 15 Step 5 INSTALLING THE LOCK (INTERIOR) continued Once the lock interior is flush against the mounting plate, secure the lock to the plate by screwing clockwise using provided screws Insert 4 AA batteries into the lock by aligning the positive and negative orientation markings on the batteries to the battery chamber.
- Page 16 Step 6 INSTALLING THE DOOR STRIKE Close your door to see if your lock closes securely with your existing door strike. If the lock closes securely, you may keep the existing door strike without removing the old hardware. However, it’s recommended that you use our door strike.
- Page 17 DOWNLOAD THE LOCKLY ® APP Congratulations! You have completed the LOCKLY Model 6S physical lock installation. To complete your setup, download the LOCKLY app from the App Store or on Google Play and follow below on-screen instructions. Scan or visit...
- Page 18 Add more Smart to your Home Secure Link Wi-Fi Hub Add the optional LOCKLY Secure Link Wi-Fi Hub, together with the free LOCKLY app, it's easier than ever to securely control and manage your door from anywhere, anytime. Real-time, monitoring, & status...
- Page 19 FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 20 INSTALLATION OVERVIEW & PARTS LIST Battery Cover BM4 × 8MM Screw Interior Assembly KA4 x 20MM Screw Mounting Plate Pin insert for Interior Adhesive changing handle orientation Exterior Activation Card Exterior Adhesive M4 Screw Positioning Rod LOCK SERIAL PGDXXXXXXXXXXXXXXXX For installing Spindle ACTIVATION CODE M4X25mm, for door thinkness, 1-3/8"~1-2/3"(35~42mm)
-
Page 21: Connect With Us
Connect with us @meetLOCKLY | #LOCKLY... - Page 22 Reference installation parts overview foldout.
- Page 23 Bluetooth SIG, Inc. , and ® any use of such marks by LOCKLY is under license. Other trademarks and trade names are those of their respective owners. Google, Android, Google Play and Google Home are trademarks of Google LLC. , Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc., or its affiliates.