Reece Posh Solus Mk3 9508808 Installation Instructions

Posh Solus Mk3 Extended Basin Mixer (4*)
Posh Solus Mk3 Extended Basin Mixer (4*)
Posh Solus Mk3 Extended Basin Mixer (4*)
Mixer must be installed to the requirements of AS/NZS 3500 by a qualified plumber. Your mixer comes to you
already factory assembled and tested. We do not recommend the dismantling of any internal part of the mixer.
IMPORTANT NOTE:
IMPORTANT NOTE:
The mixers are factory tested and sealed so as to give the best performance.
Mixer must be installed to the requirements of AS/NZS 3500 by a qualified plumber. Your mixer comes to
Mixer must be installed to the requirements of AS/NZS 3500 by a qualified plumber. Your mixer comes to
Installer is responsible for ensuring water connections to the mixer body are watertight.
you already factory assembled and tested. We do not recommend the dismantling of any internal part of the
you already factory assembled and tested. We do not recommend the dismantling of any internal part of the
mixer. The mixers are factory tested and sealed so as to give the best performance.
INSTALLATION REQUIREMENTS: mixer. The mixers are factory tested and sealed so as to give the best performance.
1. Flush out new pipe work prior to connecting the new mixer
INSTALLATION INSTRUCTIONS:
2. Place the rubber sealing washer (8) and dress ring (7) over the tap hole. Ensure that the base washer sits
INSTALLATION INSTRUCTIONS:
firmly inside the basin mixer dress ring (7).
1. Flush out new pipe work prior to connecting the new mixer
1. Flush out new pipe work prior to connecting the new mixer
3. Pass the pre-fitted hot and cold hoses (10) through the tap hole and sit the base of the basin mixer on top
2. All mixers should be installed with isolating stop cocks (Arco).
of the tap hole.
2. All mixers should be installed with isolating stop cocks (Arco).
4. Pass the undermount seal and horseshoe plate from the fixing kit (9) through the basin mixer shanks. Use
3. In some areas where the incoming water exceeds 500kpa, an approved pressure
3. In some areas where the incoming water exceeds 500kpa, an approved pressure
the retaining nuts to secure them to the basin.
limiting device must be installed. Equal pressure for hot and cold water supply is
limiting device must be installed. Equal pressure for hot and cold water supply is
5. Cold water supply must be fitted to blue coloured hose and hot water supply must be fitted to red colour
required.
required.
hose.
4. Mixers are recommended for use on mains pressure and instantaneous systems only.
4. Mixers are recommended for use on mains pressure and instantaneous systems only.
6. Fastening nuts on pre-fitted flexible hoses (10) must be installed to a water supply utilising compliant 1/2"
male BSP threads. It is recommended that both the cold and hot water supply have a means of isolating
5. Place the base washer into position (8).
5. Place the base washer into position (8).
the supply.
6. Fit the tap body (6) into the basin hole making sure first that the flexible connectors
6. Fit the tap body (6) into the basin hole making sure first that the flexible connectors
7. Hose fastening nuts must be tightened by hand plus an additional half a turn of tightening using a wrench.
(10) are firmly tightened into base of the body.
(10) are firmly tightened into base of the body.
NOTE:
7. Do not use teflon tape on threads.
7. Do not use teflon tape on threads.
• Do not twist hose braiding to tighten hoses
8. From underneath apply your rubber horse shoe gasket (9), prior to positioning the hex nuts.
• Do not use Teflon tape or thread locking compounding on any of the threaded connections
8. From underneath apply your rubber horse shoe gasket (9), prior to positioning the hex nuts.
• Do not bend hoses in a manner that will cause them to kink and deform
9. Lock the mixer onto the basin by tightening the hex nuts (9).
9. Lock the mixer onto the basin by tightening the hex nuts (9).
• Water supply flexible hoses are pre-fitted fitted to the mixer. Do not attempt to remove hoses from
mixers
• Mixer must be installed only with pressurised hot water storage and instantaneous water systems
only
NOTE: Do not over tighten hose tail into the mixer
NOTE: Do not over tighten hose tail into the mixer
Do not twist hose braiding to tighten hoses
Do not twist hose braiding to tighten hoses
SERVICING - REPLACEMENT OF CARTRIDGE:
Do not use Teflon tape or thread locking compounding on any of the threaded
Do not use Teflon tape or thread locking compounding on any of the threaded
1. Disassemble the handle (1) from the mixer body by removing the locking grub screw cap and unscrewing
connections
connections
the locking grub screw with a 1.5 mm Allen key.
2. Unscrew the cartridge dome (2) and use a wrench to unscrew the cartridge locknut (3).
SERVICING - REPLACEMENT OF CARTRIDGE:
3. Remove and replace the mixer cartridge (4). Reassemble the locknut (3), cartridge dome (2) and handle SERVICING - REPLACEMENT OF CARTRIDGE:
assembly (1).
1. Lift off acrylic indicator cap (1) and unscrew the locking grub screw using allen key.
1. Lift off acrylic indicator cap (1) and unscrew the locking grub screw using allen key.
4. Test reassembled mixer for leaks
2. Lift off handle (1) and remove cover dome (2), unscrew brass locking nut (3) and lift out
2. Lift off handle (1) and remove cover dome (2), unscrew brass locking nut (3) and lift out
CLEANING RECOMMENDATIONS cartridge (4).
cartridge (4).
We recommend the use of soapy water or approved cleaners.
3. Replace cartridge (4), replace brass locking nut (3) and replace handle (1). Tighten
3. Replace cartridge (4), replace brass locking nut (3) and replace handle (1). Tighten
This product should not be cleaned with abrasive materials.
grub screw and push in indicator cap.
grub screw and push in indicator cap.
Damage caused by any improper treatment is not covered by the product warranty - refer to Warranty Condi-
tions.
CLEANING RECOMMENDATIONS
CLEANING RECOMMENDATIONS
Please ensure a copy of the installation instructions is left with the end user for future reference.
We recommend the use of soapy water or approved cleaners.
We recommend the use of soapy water or approved cleaners.
This product should not be cleaned with abrasive materials.
This product should not be cleaned with abrasive materials.
Damage caused by any improper treatment is not covered by the product warranty - refer to Warranty Conditions
Damage caused by any improper treatment is not covered by the product warranty - refer to Warranty Conditions
Please ensure a copy of the installation
Please ensure a copy of the installation
instructions is left with the end user for future reference
instructions is left with the end user for future reference
Installation Instructions
Installation Instructions