Advertisement
Quick Links
5T H G E N RAV4
R OOF R AC K
IN S TAL L I NSTRU C TIO NS
Please read the mounting instructions below carefully before attempting to install.
Check out the install video on the product page for factory rack disassembly.
Thank you for purchasing from Victory 4x4! Checkout our website, victory4x4.com for other great off-road
products. Be sure to rate and review our product online. If you have any questions or are missing parts, please
don't hesitate to call us at 269-459-8447!
Advertisement
Related Manuals for Victory 4x4 VRAV4RK
Summary of Contents for Victory 4x4 VRAV4RK
- Page 1 Check out the install video on the product page for factory rack disassembly. Thank you for purchasing from Victory 4x4! Checkout our website, victory4x4.com for other great off-road products. Be sure to rate and review our product online. If you have any questions or are missing parts, please...
-
Page 2: Inclu De D H Ar Dwar E
INCLU DE D H AR DWAR E 1/4"-20 X 3/4" 1/4"-20 X 3/8" Button Head Button Head Included with light bar cutout option. 1/4"-20 1/4"-20 T-Nut Serr. Flange Nut Included with light bar cutout option. 1/4” ID 1/4"-20 Washer Nylon-Insert Flange Nut 5/16”-18 5/16”-18 X 3/4”... -
Page 3: Included Parts
I NC LU D E D PA RTS 1L/1R 1L/1R 1L/1R Included with light bar cutout option. 1L/1R... - Page 4 A SS E M BLY Assemble the rack on the ground. Start by mounting the crossbars between the two side rails. For this, use the1/4”-20 X 3/4” button head bolts and the 1/4” ID washers (two per bar per side). Make sure the machined slot in the rail of the crossbar is facing up, so that you can easily add t-nuts to mount your gear.
- Page 5 A SS E M BLY Next, mount the strip of trim to the bottom edge of the front fairing. Start just to the outside of the peak of the bottom edge and continue until it reaches the equivalent point on the other side of the fairing. Cut off any extra.
- Page 6 AS SE M BLY Mount the front and rear fairings. To do this, use the 1/4”-20 X 3/4” button head bolts, 1/4” ID washers, and 1/4”-20 serrated flange nuts. The front fairing will need three of each per side and the rear fairing will need two of each per side.
- Page 7 AS SE M B LY Next, attach the mounts to the roof of the vehicle. Start by putting RTV around each mounting hole on the roof. Then, place the mount in position and apply more RTV over the holes in the mount so the bolts will have to pass through it when tightening.
- Page 8 ASSEMBLY Next, put the assembled rack onto your roof and attach it to the mounts using the 1/4”-20 X 3/4” button head bolts, 1/4” washers and 1/4” serrated flange nuts. Once they are loosely attached to the rack, tighten the mounts fully to the roof . Then, make whatever adjustments to the rack that are necessary to get an even gap between the bottom edge of the side rails and the roof down the length of the vehicle and tighten the mounts fully to the side rails.
- Page 9 A S S E M B LY Finally, push the front and rear fairings down tight to the roof of the vehicle and tighten everything fully into place. We recommend applying clear 3M paint protection film to the roof of the vehicle anywhere the edge trim/fairings make contact with the roof.
- Page 10 4 0” L IG HT B AR A S S E M B LY Slide 2 t-nuts into each of the channels on the top side of the front-most crossbar using the slots. Then, place each light bar mount over one pair of t-nuts and loosely bolt it in place using the 1/4”-20 X 3/8”...
- Page 11 D I M E N SI O N S...
Need help?
Do you have a question about the VRAV4RK and is the answer not in the manual?
Questions and answers