Subscribe to Our Youtube Channel
Related Manuals for Roborock Qrevo Curv
Summary of Contents for Roborock Qrevo Curv
- Page 1 Roborock Qrevo Curv Robotic Vacuum Cleaner User Manual Read this user manual with diagrams carefully before using this product and store it properly for future reference.
-
Page 2: Table Of Contents
English Contents 04 Safety Information 05 International Symbols Explanation 06 Product Overview 07 Installation 08 Connecting to the App 08 Instructions for Use 10 Routine Maintenance 12 Basic Parameters 13 Common Issues... -
Page 3: Safety Information
Restrictions WARNING • For the purposes of recharging the battery, only use the detachable docking station roborock EWFD26HRR or EWFD27HRR provided with this product. • The product must be switched off and the plug must be removed from socket outlet before cleaning or maintaining the product. -
Page 4: International Symbols Explanation
• Always operate the device in well-ventilated areas to prevent overheating. • Roborock disclaims all liability for indirect, incidental, or consequential damages resulting from the use, misuse, or inability to use this product. This disclaimer does not affect any statutory rights that may not be disclaimed under applicable law. -
Page 5: Product Overview
Product Overview A1-7—Bumper Dustbin A1-8—Wall Sensor A6-1—Dustbin Latch Robot (Top View) Robot (Bottom View) A6-2—Suction Inlet A6-3—Air Inlet —Power/Clean A2-1—Cliff Sensors A6-4—Washable Filter A2-2—Carpet Sensor • Press and hold to turn the robot A6-5—Filter Latch A2-3—Side Brush on or off Power Cord A2-4—Main Brush Cover •... -
Page 6: Installation
A10-14—Drying Air Outlets Assembly • Maintain the dock according to the Routine Maintenance. Do not clean the dock power cord and A10-15—Dock Location Beacon charging contacts with a wet cloth or tissue. B2-1—Align and install the mop axles into A10-16—Suction Inlet •... -
Page 7: Connecting To The App
Cleaning range: The robot cleans a 1.5 m (4.9 ft) × • To prevent damage, do not use any disinfectant and Open the Roborock app, tap the “Add only use cleaning solution recommended by Roborock. 1.5 m (4.9 ft) square area centered on itself. - Page 8 Sleep • Mop wash frequency and mode can be modified in the Note: If the robot fails to find the dock, it will app. automatically return to its starting position. Place the If the robot is paused for over 10 minutes, robot on the dock manually to recharge.
-
Page 9: Routine Maintenance
Routine Maintenance Dustbin Notes: • To securely install the main brush cover, make sure to * Clean as required. press both of the main brush cover latches in place. Note: The frequency of replacement may vary with the • It is recommended to wipe the main brushes with a D5-1—Remove the magnetic top cover of actual situation. - Page 10 Mop Cloths Dirty Water Tank Note: Make sure the disposable dust bag is properly installed to avoid waste escaping and damaging the * Clean as required and replace every 1-3 months. * Clean as required. dock. D7-1—Remove the mop cloths from mop Open the dirty water tank lid and pour out D12-4—Reinstall the dust container cover cloth mounts.
-
Page 11: Basic Parameters
Basic Parameters Robot Model V10VIV 14.4 V/6400 mAh (TYP) Battery lithium-ion battery Rated Input 20 VDC 1.5 A Charging Time Approx. 4 hours Note: The serial number is on a sticker on the underside of the robot. Empty Wash Fill Dock Model EWFD26HRR Rated Input Voltage 220-240 VAC... -
Page 12: Common Issues
• Check dirty water tank placement or empty the tank • Unable to connect to WiFi abruptly. There may be an as required. error with your router settings. Contact Roborock • The cleaning tray module or cleaning tray filter is not Customer Service for help with troubleshooting. - Page 13 Common Issues Issue Solution Issue Solution • The main brushes or main brush cover is not properly • The mop cloths will not be washed if not used. Reduced emptying installed. Check and install in place. • If the robot does not start from the dock or no dock performance or •...
- Page 14 Manufacturer: Beijing Roborock Technology Co., Ltd. Address of Manufacturer: Room 1001, Floor 10, Building 3, Yard 17, Anju Road, Changping District, Beijing, P.R. China For more product information, visit our website: www.roborock.com For after-sales support, email our after-sales service team: Europe Support: support@roborock-eu.com...
Need help?
Do you have a question about the Qrevo Curv and is the answer not in the manual?
Questions and answers