Related Manuals for Roborock Q Revo
Summary of Contents for Roborock Q Revo
- Page 1 Roborock Q Revo Robotic Vacuum Cleaner User Manual Read this user manual with diagrams carefully before using this product and store it properly for future reference.
- Page 2 English Français Español...
-
Page 3: Table Of Contents
English Contents Safety Information Battery and Charging International Symbols Explanation FCC/IC Statement Product Overview Installation Connecting to the App Instructions for Use Routine Maintenance Basic Parameters Environmental Protection Description Common Issues... -
Page 4: Safety Information
Safety Information WARNING • For use only with roborock EWFD11LRR or EWFD12LRR docking station. • Place the cords from other appliances out of the area to be cleaned. • Do not operate the vacuum in a room where an infant or child is sleeping. -
Page 5: Battery And Charging
Safety Information Battery and Charging • To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. -
Page 6: Fcc/Ic Statement
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Correspondence of the responsible party in USA Company Roborock Technology Co. Address ROOM 1227, 12TH FLOOR, 1000 N. WEST STREET, WILMINGTON, DE 19801 Email... -
Page 7: Product Overview
Product Overview Robot (Upper Cover Open) Dock Base A3-1—Vertical Bumper Power Cable Robot (Top View) A3-2—LiDAR Sensor A3-3—WiFi Indicator —Power/Clean Disposable Dust Bag • Off: WiFi disabled • Press and hold to turn the robot on • Flashing slowly: Waiting for connection or off Dock •... -
Page 8: Installation
Avoid narrow spaces or locations where the Attach the base by pressing down robot may be suspended in the air. Option 1: Search for “Roborock” in the App • Placing the dock on a soft surface (carpet/mat) may both sides of the base firmly, and then... -
Page 9: Instructions For Use
Note: After spot cleaning, the robot will automatically return to the starting point and enter Standby mode. Starting Cleaning Open the Roborock or Mi Home App, tap “+” Pause and add the device as instructed in the app. Press the button to start cleaning. - Page 10 Sleep Emptying System Reset If the robot is paused for over 10 minutes, it Auto-emptying will automatically begin when If the robot does not respond when a will go to sleep, and the power indicator will the robot returns to the dock after cleaning. button is pressed or cannot be turned off, flash every few seconds.
-
Page 11: Routine Maintenance
Routine Maintenance Omnidirectional Wheel Washable Filter * Clean as required * Clean every two weeks and replace the filter every 6-12 months Main Brush D3-1—Use a tool, such as a small D6-1—Remove the filter. screwdriver, to pry out the axle and * Clean every 2 weeks and replace every 6-12 months D6-2—Rinse the filter repeatedly and tap it take out the wheel. -
Page 12: Basic Parameters
Moving Dock D12-3—Clean around the filter with a dry Empty Wash Fill Dock cloth. Install a new disposable dust Lift up and move the dock. Do not move the EWFD11LRR or bag in place along the slot and Model dock by lifting dock base, water tank handles EWFD12LRR unfold the dust bag to maximize or dust container cover directly to prevent... -
Page 13: Environmental Protection Description
Environmental Protection Description Removing the battery * The following information applies only when disposing of the robot and should not be followed for day-to-day operations The chemical substances contained in the built-in lithium-ion battery of this product can cause environmental pollution. Before disposing of this product, remove the battery. -
Page 14: Common Issues
Unable to connect to WiFi. • Abnormal WiFi connection. Reset the WiFi, download the latest mobile app, and retry. • Unable to connect to WiFi abruptly. There may be an error with your router settings. Contact Roborock customer service for additional support. - Page 15 Common Issues Problem Solution The robot suddenly misses a certain spot. • The wall sensor, cliff sensors or carpet sensor may be dirty. Wipe them with a soft dry cloth. • Voltage error. Check that local voltage meets the requirements listed on the dock. The LED status indicator light on the dock •...
Need help?
Do you have a question about the Q Revo and is the answer not in the manual?
Questions and answers