Roborock Qrevo Plus User Manual
Hide thumbs Also See for Qrevo Plus:

Advertisement

Quick Links

Roborock Qrevo Plus
Robotic Vacuum Cleaner User Manual
Read this user manual with diagrams carefully before using this
product and store it properly for future reference.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Qrevo Plus and is the answer not in the manual?

Questions and answers

Summary of Contents for Roborock Qrevo Plus

  • Page 1 Roborock Qrevo Plus Robotic Vacuum Cleaner User Manual Read this user manual with diagrams carefully before using this product and store it properly for future reference.
  • Page 3 English Français Deutsch Italiano Español Nederlands Polski Norsk Svenska...
  • Page 4: Table Of Contents

    English Contents Safety Information Product Overview Installation Connecting to the App Instructions for Use Routine Maintenance Basic Parameters Common Issues...
  • Page 5: Safety Information

    WARNING For the purposes of recharging the battery, only use the detachable docking station roborock EWFD24HRR or EWFD25HRR provided with this product. The product must be switched off and the plug must be removed from socket outlet before cleaning or maintaining the product.
  • Page 6 Always operate the device in well-ventilated areas to prevent overheating. Roborock disclaims all liability for indirect, incidental, or consequential damages resulting from the use, misuse, or inability to use this product. This disclaimer does not affect any statutory rights that may not be disclaimed under applicable law.
  • Page 7: Product Overview

    Product Overview A2-8—Mop Cloths Dustbin A2-9—Cliff Sensors A6-1—Dustbin Latch Robot (Top View) A6-2—Air Inlet Robot (Top Cover Open) A6-3—Washable Filter —Power/Clean A3-1—Vertical Bumper A6-4—Suction Inlet Press and hold to turn the robot A3-2—LiDAR Sensor on or off Dock Base A3-3—WiFi Indicator Light Press to start cleaning Off: WiFi disabled/Charging —Power Indicator Light...
  • Page 8: Installation

    A10-17—Water Level Float Assembly The dock status indicator light is on when the dock is powered on, and off when the robot is charging. A10-18—Cleaning Tank Filter The dock status indicator light turns red if an error occurs. B2-1—Place the dock on a hard, flat floor A10-19—Cleaning Tank Place the dock on a flat floor away from fire, heat, and (wood/tile/concrete etc.), flat against...
  • Page 9: Connecting To The App

    Only 2.4 GHz WiFi is supported. one, thoroughly and efficiently. If the robot waits more than 30 minutes for a connection, Search for “Roborock” in the App Store or WiFi will be automatically disabled. If you want to C2-1—Zone 1 – Cleaned.
  • Page 10 Pause tap the corresponding button in the app. The power indicator light will breathe during Press any button to stop washing. robot charging. When the robot is running, press any button Notes: Note: If the robot fails to find the dock, it will automatically to pause it, press the button to resume return to its starting position.
  • Page 11: Routine Maintenance

    Routine Maintenance Side Brush Note: To prevent blockage, only use clean water without any cleaning liquid. * Clean monthly and replace every 3-6 months. D5-4—Leave the dustbin and washable filter Note: The frequency of replacement may vary with the Unscrew the side brush screw. Remove and to dry.
  • Page 12: Basic Parameters

    Basic Parameters D8-1—Dock Locator Replacing Disposable Dust Bag D8-2—Reactive Tech Obstacle Avoidance Sensor * Replace as required. Robot D8-3—Wall Sensor D12-1—Remove the dust container cover. D8-4—Communication Sensor D12-2—Remove the disposable dust bag in Model QR2PSL D8-5—Carpet Sensor the direction of the arrow as shown D8-6—Four Cliff Sensors 14.4 V/5200 mAh (TYP) and discard it.
  • Page 13: Common Issues

    Dock not connected to power. Check whether both Unable to connect to WiFi abruptly. There may be an ends of the power cord are properly connected. error with your router settings. Contact Roborock Customer Unable to Poor contact. Clean the charging contacts of the dock Service for help with troubleshooting.
  • Page 14 Common Issues Issue Solution Issue Solution The robot Auto-emptying is disabled. Check in-app settings. The wall sensor, cliff sensors, or carpet sensor may be suddenly misses Dock dust container cover is not installed. Check and install. dirty. Clean them with a soft, dry cloth. a certain spot.

This manual is also suitable for:

Qr2psl

Table of Contents