Dvd Player With Component Video; Dvi Device - Brother HL-2600CN Owner's Manual

Connecting a DVD Player with Component Video
Connecting a DVI Device

DVD Player with Component Video

Figure 9
Component video cables and audio cables are required.
These are not included with the TV.
1. Connect the Component Video cables from Y/Pr/
Pb VIDEO OUT on the back of the DVD player to
COMPONENT-2 on the TV back panel, matching the
correct connection:
• Y to Y (Green)
• Pr to Pr (Red)
• Pb to Pb (Blue)
2. Connect a set of audio cables from AUDIO OUT
on the back of the DVD player to COMPONENT-2
AUDIO Input on the TV back panel. The red cable
connects to the R (right) channel, and the white cable
connects to the L (left) channel.
INPUT
1
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DTV/CABLE/
VHF/UHF
Figure 9. Connecting a DVD Player with Component
Video
Note: NetCommand® assumes you connected your
DVD player to Component-2. If you add a second
DVD or use any other inputs for your DVD, this change
must match in the NetCommand system. See Edit
NetCommand... in Chapter 3 for more information.
IMPORTANT
See Appendix B for component video signal
compatibility information.
For digital audio connections to your A/V
receiver , see your DVD player and A/V
receiver Owner's Guides.
COMPONENT
YPbPr (480i/480p/720p/1080i)
1 2
2
INPUT OUTPUT
Y
DVI AUDIO RECORD
Analog Audio OUTPUT OUTPUT
Pb
1 2
VIDEO
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
LEFT/
(MONO) AUDIO-
RIGHT
AUDIO-
RIGHT
MONITORLINK™/HDMI
PC - 60Hz
VIDEO 480i/480p/720p/1080i
VGA, W-VGA,
AUDIO PCM LINEAR
SVGA, W-SVGA,
XGA, 1280 X 720
1 2
IR EMITTER
Net Command
DIGITAL
AUDIO
ANT 1 / MAIN ANT 2 / AUX OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
IEEE 1394
INPUT/
OUTPUT

DVI Device

Figure 10
A DVI-to-HDMI cable or DVI/HDMI adaptor and HDMI cable
and audio cables are required. These are not included with the
TV. They may be available at your local electronics retailer.
1. Connect the DVI-to-HDMI cable (recommended) or
HDMI cable with DVI/HDMI adaptor from the DVI
device's back panel to the TV back panel.
NOTE: If you are using a DVI/HDMI adaptor, it is
important to connect the adaptor to the DVI device
for best performance.
2. Connect a set of audio cables from AUDIO OUT
on the DVI device back panel to the INPUT/DVI
Analog Audio on the TV back panel. The red cable
connects to the R (right) channel, and the white
cable connects to the L (left) channel.
NOTE: The HDMI connection supports copy
protection (HDCP). Some devices require
connecting to an analog input first, in order to view
on-screen menus and select DVI as the ouput.
Please review your equipment instructions for DVI
connectivity and compatibility.
COMPONENT
INPUT YPbPr (480i/480p/720p/1080i)
1 2
1 2
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
IR EMITTER
Net Command
DTV/CABLE/
VHF/UHF
DIGITAL
AUDIO
ANT 1 / MAIN OUTPUT
ANT 2 / AUX
Figure 10. Connecting a DVI Device
CAUTION: To ensure continued FCC
compliance, the user must use a
shielded video interface or HDMI cable
with bonded ferrite cores at both ends
when using the PC input.
Chapter 2. Connecting
INPUT OUTPUT
Y
DVI AUDIO RECORD
Analog Audio OUTPUT OUTPUT
Pb
1 2
VIDEO
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
LEFT/
(MONO) AUDIO-
RIGHT
AUDIO-
RIGHT
MONITORLINK™/HDMI
PC - 60Hz
VIDEO 480i/480p/720p/1080i
VGA, W-VGA,
AUDIO PCM LINEAR
SVGA, W-SVGA,
XGA, 1280 X 720
1 2
CableCARD™ ANT 1 CARD TOP
USE WITH
IEEE 1394
INPUT/
OUTPUT
29