Table of Contents
Advertisement
Quick Links
w w w . t h e - m s p a . c o m
Owner's Manual
P-SH063 Soho
P-CA043/063
Camaro
P-EX043/063
Exotic
EN
DO NOT RETURN MERCHANDISE TO YOUR DEALER STORE DIRECTLY. CALL MSPA AFTER
SALES SERVICE CENTER FOR ANY PRODUCT-RELATED QUESTIONS OR CONTACT MSPA AT
info@the-mspa.com
Due to MSpa continuous product improvement, MSpa reserves the right to change the product appearance and specifications, which
may result in updates to the instruction manual without notice.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for mspa Exotic P-EX043
Summary of Contents for mspa Exotic P-EX043
- Page 1 SALES SERVICE CENTER FOR ANY PRODUCT-RELATED QUESTIONS OR CONTACT MSPA AT info@the-mspa.com Due to MSpa continuous product improvement, MSpa reserves the right to change the product appearance and specifications, which may result in updates to the instruction manual without notice.
-
Page 2: Table Of Contents
To guide you in your initial MSpa experience, we are pleased to present you with this instruction manual. Please read this manual carefully before using the product for the first time. We are delighted to welcome you to the MSpa family, and look forward to sharing with you the full spectrum of our expertise. -
Page 3: Safety Precautions
SAFETY PRECAUTIONS For your own safety and that of your product, please make sure to follow the safety precautions below. Failure to follow the instructions may result in serious injury, property damage or death. Improper installation or operation will void the warranty. PLEASE ENSURE THAT YOU READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS KEEP THIS MANUAL FOR FUTURE REFERENCE DANGER... - Page 4 ● Do not use the spa if it is damaged on delivery and/or if it malfunctions in any way. ● Contact the MSpa service center for further instructions. ● Keep all pets away from the spa to avoid any damage.
- Page 5 CAUTION ● Always add chemicals to water, never add water to chemicals. Adding water to chemicals may cause strong fumes or violent reactions and hazardous chemical spray. ● For water that has already been used, dispose of it promptly or use water chemicals for cleaning. Usually, it is recommended to drain and refill a spa with clean water every 3-5 days.
- Page 6 Warning: The appliance's water protection levels vary across different product zones, as shown in the following diagram. (The installation regulations comply with IEC 60364-7-702.) 2.5 m Zone 2 Zone 1 Zone 2 2.5 m Zone 0 Zone 0 1.5 m 2.0 m 2.0 m 1.5 m...
-
Page 7: Specifications
SPECIFICATIONS BUBBLE SPA Seating Water Outside Inside Model No. / Temp Increasing Shape Height Weight Capacity Capacity Dimensions Dimensions Code Rate 930Ltr 1.85m 1.45m 0.68m 35.5kg P-SH063 1.5-2.0 °C/h Square SOHO (245gal) (73”) (57”) (27”) (78.3lbs) P-CA043 700Ltr 1.80m 1.40m 0.70m 31.5kg 1.5-2.0 °C/h... -
Page 8: First Use And Set-Up Preparation
REF. NO. PARTS DESCRIPTION QTY. Spa cover with aluminum foil inside (Soho P-SH063 comes with a ground mat with the cover) Spa tub Wired controller Heat preservation bubble mat (For P-CA043/063) Heat preservation foam mat (For P-EX043/063) Digital lock (except for Soho P-SH063) Inflation hose for bladder Filter cartridge*2, cartridge base*1 Spa drain valve adaptor... -
Page 9: Spa Set-Up
2. Lay out all the parts on the ground and make sure all parts are accounted for. Make sure the spa tub is right side up. (*For missing or damaged part, contact the MSpa Service Center) 3. Spread the Heat Preservation Ground Mat over a cleared area. Spread out the spa liner over the ground mat. The heat Preservation Mat prevents heat loss from the bottom of the unit. - Page 10 Yellow Green White Note: Before inflation, check whether the manometer cap is screwed up tight on the valve of pool body. If not, please tighten and then inflate. After inflation, the manometer cannot be removed, otherwise the air will be released. When the Yellow section is pushed out, the Spa inflation is completed.
-
Page 11: Wired Controller Operation
6.6 Turn on the Heater on the spa wired controller, refer to the “Wired Controller Operation” section. Maximum heating temperature is 40°C (104°F). Zipper and Buckle Operation 7.1 Digital Lock Operation The default password is “000”. Follow the steps below to change the password: ●... - Page 12 LED display °C °F Once powered-up, press the RESET on the PRCD. The LED displays the current water temperature automatically. NOTE: The actual water temperature may vary from the temperature displayed on the LED screen by as much as approximately 1°C. HEATING 1.
-
Page 13: Water Maintenance And Chemicals
WATER MAINTENANCE AND CHEMICALS CAUTION: ALWAYS ENSURE THE SPA IS UNPLUGGED BEFORE BEGINNING ANY MAINTENANCE WORK TO AVOID THE RISK OF INJURY OR DEATH. FILTER CARTRIDGE MAINTENANCE 1. Inspect and clean the filter cartridge gently after each use. Follow the steps below: NOTE: Change the filter cartridge every 3-5 days, or if the filter cartridge remains soiled and discolored. -
Page 14: Drainage, Cleaning And Storage
Water Treatment: ● It is good practice with an existing spa to keep all air jets open and valves closed to allow chemically treated water to flush through all pipework. Always follow the chemical manufacturer’s directions, and the health and hazard warning. ●... -
Page 15: Precautions For Seasonal Use
Cleaning The Spa Tub If dirt is visible in the water or if the water becomes cloudy and the correct water chemistry does not clear it up, change the water and clean the spa tub. See the “Spa tub drainage” section on how to drain the spa. While empty, clean and/or replace the filter cartridge. Use a sponge and mild soap solution to wipe away any soil or stains on the inside of the spa wall. -
Page 16: Disposal And Environmental Protection
PRECAUTIONS FOR SEASONAL USE Inflatable hot tubs are made of reinforced PVC material, whose nature decides the hot tubs are easily affected by weather and temperature. Please do pay special attention when using the spa under different seasonal conditions. In Summer / Sunny days Direct sunshine and hot weather will both lead the spa liner to expand. -
Page 17: Troubleshooting
ERROR CODE CHART LED READING CAUSE SOLUTION Water temperature is lower than 0°C degree or exceeds 55°C (131°F) Change the water or contact local MSpa Service Center. Temperature sensor failure Waterflow switch failure Contact local MSpa Service Center. Filter failure Add water above the minimum line. - Page 18 2. The corresponding service provider will be displayed. * You can find the contact information of local service center on the back of the warranty card CONTACT YOUR LOCAL MSPA DEALER OR SERVICE CENTER FOR ANY PRODUCT-RELATED QUESTIONS OR PROBLEMS.
-
Page 19: Mspa Limited Warranty
● Warranty service outside the country of purchase is limited to the terms and conditions of the corresponding warranty in the country of service. Where the cost of repairs or replacement is not covered by this warranty, MSpa will advise the owners and the cost shall be charged to the owner.
Need help?
Do you have a question about the Exotic P-EX043 and is the answer not in the manual?
Questions and answers