Page 1
SALES SERVICE CENTER FOR ANY PRODUCT-RELATED QUESTIONS OR CONTACT MSPA AT info@the-mspa.com Due to MSpa continuous product improvement, MSpa reserves the right to change the product appearance and specifications, which 3127647 may result in updates to the instruction manual without notice.
To guide you in your initial MSpa experience, we are pleased to present you with this instruction manual. Please read this manual carefully before using the product for the first time. We are delighted to welcome you to the MSpa family, and look forward to sharing with you the full spectrum of our expertise.
IMPORTANT SAFETY INSTRUCTIONS For your own safety and that of your product, make sure to follow the safety precautions below. Fail to follow the instruction may result in serious injury, property damage or death. Improper installation or operation will void the warranty.
Page 4
The plug of spa shall be more than 3.5m away from the pool. WARNING: WARNING: Spray head must not be used. WARNING: The outlet of Spa must not be connected to any tap or fitting other than those specified. WARNING: Electric installations should fulfill the requirements of local standards.
Page 5
A green coloured terminal or a terminal marked G, GR, Ground, Grounding, or the symbol* is located inside the electric box. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying this equipment.
Page 6
WARNING: Please carefully read the warning label at the first time you are going to use MSpa. Please post this warning label on where is at a distance to MSpa within 1.5m/5’, people in spa can see it clearly. Please retain this information for future reference.
REF. NO. PARTS DESCRIPTION QTY. Spa cover with aluminum foil inside (Soho P-SH069 comes with a ground mat with the cover) Spa tub Wired controller Heat preservation bubble mat (For P-CA049/069) Heat preservation foam mat (For P-EX049/069) Digital lock (except for Soho P-SH069) Inflation hose for bladder Filter cartridge*2, cartridge base*1 Spa drain valve adaptor...
2. Lay out all the parts on the ground and make sure all parts are accounted for. Make sure the spa tub is right side up. (*For missing or damaged part, contact the MSpa Service Center) 3. Spread the Heat Preservation Ground Mat over a cleared area. Spread out the spa liner over the ground mat. The heat Preservation Mat prevents heat loss from the bottom of the unit.
Page 10
Yellow Green White Note: Before inflation, check whether the manometer cap is screwed up tight on the valve of pool body. If not, please tighten and then inflate. After inflation, the manometer cannot be removed, otherwise the air will be released. When the Yellow section is pushed out, the Spa inflation is completed.
6.6 Turn on the Heater on the spa wired controller, refer to the “Wired Controller Operation” section. Maximum heating temperature is 40°C (104°F). Zipper and Buckle Operation 7.1 Digital Lock Operation The default password is “000”. Follow the steps below to change the password: ●...
Page 12
LED display °C °F Once powered-up, press the RESET on the GFCI. The LED displays the current water temperature automatically. NOTE: The actual water temperature may vary from the temperature displayed on the LED screen by as much as approximately 1°C (33.8°F). HEATING 1.
WATER MAINTENANCE AND CHEMICALS CAUTION: ALWAYS ENSURE THE SPA IS UNPLUGGED BEFORE BEGINNING ANY MAINTENANCE WORK TO AVOID THE RISK OF INJURY OR DEATH. FILTER CARTRIDGE MAINTENANCE 1. Inspect and clean the filter cartridge gently after each use. Follow the steps below: NOTE: Change the filter cartridge every 3-5 days, or if the filter cartridge remains soiled and discolored.
Water Treatment: ● It is good practice with an existing spa to keep all air jets open and valves closed to allow chemically treated water to flush through all pipework. Always follow the chemical manufacturer’s directions, and the health and hazard warning. ●...
Spa Tub and Air Bladder Repair Use the enclosed repair patch to repair any puncture: 1. Clean and dry the area to be repaired thoroughly 2. Apply the glue to the PVC patch and quickly attach it onto the damaged surface. (Glue is not included) 3.
ERROR CODE CHART LED READING CAUSE SOLUTION Water temperature is lower than 0°C degree or exceeds 55°C (131°F) Change the water or contact local MSpa Service Center. Temperature sensor failure Waterflow switch failure Contact local MSpa Service Center. Filter failure Add water above the minimum line.
Page 17
SHAPE damage to the spa pool Spa inlet/outlet connection not securely tight Tighten the inlet and outlet connection Close the drainage valve. Contact the MSpa Service Center, if spa SPA LEAKING Drainage valve is not closed completely is still leaking...
● Warranty service outside the country of purchase is limited to the terms and conditions of the corresponding warranty in the country of service. Where the cost of repairs or replacement is not covered by this warranty, MSpa will advise the owners and the cost shall be charged to the owner.