Table of Contents
Advertisement
Quick Links
User Manual
DA14531 Development Kit Pro
Hardware
UM-B-114
Abstract
Renesas DA14531 development kit PRO consists of one DA145xx DEVKT-P PRO-Motherboard,
FCGQNFN daughterboard and a WLCSP daughterboard (the WLCSP daughterboard must be
purchased separately). This user manual describes the system functions of the hardware as well as
the guidelines of how to enable or disable features of the DA14531 development kit PRO.
Advertisement
Table of Contents
Related Manuals for Renesas Pro DA14531
Summary of Contents for Renesas Pro DA14531
-
Page 1: Abstract
Hardware UM-B-114 Abstract Renesas DA14531 development kit PRO consists of one DA145xx DEVKT-P PRO-Motherboard, FCGQNFN daughterboard and a WLCSP daughterboard (the WLCSP daughterboard must be purchased separately). This user manual describes the system functions of the hardware as well as... -
Page 2: Table Of Contents
Configuration of DA14531 DK PRO with a DA14531 WLCSP17 PRO-DB ......44 Current Measurements ....................... 45 Current Measurement Circuit of PRO-MB ................45 Power Profiler of Smartsnippet Toolbox ................46 Power Profiler Setup ......................47 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 2 of 85... - Page 3 Terms and Definitions ........................9 References ............................. 9 Introduction..........................10 System Overview ........................ 12 3.1.1 Features of DA14531 PRO-DB ................12 3.1.2 Features of DA14531 PRO-MB ................12 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 3 of 85...
- Page 4 Switching Transient Artifacts of Current Measurement Circuit ........... 55 Push Button SW3 ........................ 55 mikroBUS Wrong Labels ..................... 56 4-Wire UART Special Considerations ................. 56 Appendix A FCGQFN24 PRO-DB: DA14531-00FXDB-P_(376-04-F2) ..........58 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 4 of 85...
- Page 5 Adding External Resistor to VLDO Selection (J5) Pin Header ........... 81 Using External Power Supply ..................... 81 Important Notice For Boost Operation ................81 Appendix H DA14531 PRO-MB PCBA Label ................... 83 Revision History ..........................84 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 5 of 85...
-
Page 6: Figures
Figure 53: Disable SW3. Remove Jumper from J19:4-5 ..............55 Figure 54: mikroBUS Wrong Label ...................... 56 Figure 55: Full UART Configuration – CTS Issue ................57 Figure 56: Schematic, FCGQFN24, DA14531-00FXDB-P_(376-04-F2) ..........58 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 6 of 85... -
Page 7: Tables
Table 21: Pin Assignment for DA14531 FCGQFN24 PRO-DB ............71 Table 22: The Components for DA14531 DK PRO in WLCSP17 Package ........72 Table 23: The Components for DA14531 DK PRO in FCGQFN24 Package ........75 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 7 of 85... - Page 8 Table 29: The Components for the Two Packages to Support Full UART and JTAG ......79 Table 30: Information Provided on PCBA Label ................. 83 Table 31: Date Code vs SPI Flash ...................... 83 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 8 of 85...
-
Page 9: Terms And Definitions
WLCSP17 PRO-DB PRO daughterboard with DA14531 - WLCSP17 References DA14531, Datasheet, Renesas Electronics. UM-B-083, SmartSnippets Toolbox User Manual, User Manual, Renesas Electronics. AN-B-075, DA14531_Hardware_Guidelines, Application Note, Renesas Electronics. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 9 of 85... -
Page 10: Introduction
(also ordering code) for the DK PRO. DA14531-00FXDEVKT-P DK PRO PRO-MB 376-18-B Figure 1: DK PRO, DA14531-00FXDEVKT-P DK with PRO-MB and the PRO-DBs User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 10 of 85... -
Page 11: Table 1: Dk Pro Part Numbers And Description
The following sections guide users to understand the system setup, the different available configuration options, as well as the tools provided to debug, develop, and evaluate the system performance. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 11 of 85... -
Page 12: System Overview
User LEDs and push buttons (to be used with a DA14531 FCGQFN24 PRO-DB) ● Voltage translation for the JTAG and UART signals that allows the current leakage during system operation to be eliminated User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 12 of 85... -
Page 13: Getting To Know Da14531 Dk Pro
Figure 3: System Block Diagram of DA14531 PRO-DB ANT1 PCB ANTENNA Matching Debug R-Multiplexer QFN24 32MHz L1, 2.2μH 1.1V J2 – Power Measurements J1 – Mating Connector Figure 4: DA14531-00FXDB-P, FCGQFN24 PRO-DB_[376-04-F] User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 13 of 85... -
Page 14: Figure 5: Da14531-00Ogdb-P, Wlcsp17 Pro-Db_[376-05-E]
DA14531 pins as desired (Appendix To complete a configuration, it is necessary to set/remove jumpers on the DA14531 PRO-MB accordingly. The default settings are presented in Section 5. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 14 of 85... -
Page 15: Power Section
Setting SW1 to position L (Boost) connects the V pin of DA14531 to the voltage rail BAT_Low generated from U2 on the PRO-DB ○ For DA14531-00FXDEVKT-P, SW1 must be set to H position (Buck) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 15 of 85... -
Page 16: Figure 7: Power Section Of Da14531 Pro-Db
UM-B-114 DA14531 Development Kit Pro Hardware BUCK VBAT Figure 7: Power Section of DA14531 PRO-DB User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 16 of 85... -
Page 17: Rf Section
Assemble J3, SMA Female Socket 50 Ω Board Edge (142-0761-861of Cinch Connectivity Solutions Johnson) Figure 8: RF Section of DA14531 PRO-DB Figure 9: Modifications Required for Performing RF Measurements User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 17 of 85... -
Page 18: Pro-Mb (376-18-B)
Sense Circuit VLDO Selection ARDUINO J11, J12, J13, Connector USB1 KEYS MIKROBUS 1 USB HUB MIKROBUS 2 SW2 & SW3 J15, J16 J17, J18 Figure 11: PRO-MB (376-18-x) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 18 of 85... - Page 19 J6: manual enable of USB hub voltage regulator. Not in use by default. ● J20: monitoring current sense circuit. Not mounted. No functional use. ● J22: it can provide 6.0 V to PRO-DB. Not mounted. No functional use. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 19 of 85...
-
Page 20: Usb Hub (U11)
Connecting a PC to the current sensing circuitry: ○ SPI connection with ADC (U8) ○ Software cursor triggering (C_TRIG) ● Reset the capability of the DA14531 SoC through the T_RESET signal (not enabled) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 20 of 85... -
Page 21: Usb To Jtag (U4)
Functions served by U4 include: ● Connecting a PC to the JTAG port of DA14531 SoC ● Reset the capability of the DA14531 SoC through the T_RESET signal User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 21 of 85... -
Page 22: Voltage Translator
) is used as a reference. Consequently, there is DDIO BAT_HIGH no additional power consumption on the power circuitry of DA14531 PRO-MB due to voltage translation. Figure 15: Voltage Translator Circuitry of DA14531 PRO-MB User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 22 of 85... -
Page 23: 4.2.5 Power Section
BOOST Mounted Bypass VBAT VBAT_Hi 2.2u for BUCK PRO-MB 376-18-B Figure 16: Power Topology for DA14531 PRO-MB and PRO-DB Figure 17: Power Circuit for DA14531 PRO-MB User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 23 of 85... -
Page 24: Gpios And Pin Assignment And Functions Of Da14531 Dk Pro
The PRO-MB configuration is realized with jumpers or cables. J1 on the PRO-MB is the main configuration header (Figure 19). PRO-DB configuration is also feasible. See Appendix D. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 24 of 85... -
Page 25: Figure 19: J1, Configuration Header On Da14531 Pro-Mb
SWCLK (Default) J1:23-24 SWDIO P0_10 P0_5 SWDIO (Default) J8:3-4 P1_0 P0_9 PWM_1 MBus1/ARD (Default) P1_1 P0_10 RX_1 MBus1/ARD J19:4-5 No Available pins from P1_2 INT_1 MBus1/ARD DA14531 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 25 of 85... -
Page 26: Da14531 Wlcsp17 Pro-Db, Default Setup
● Note that signals of DA14531 WLCSP17 PRO-DB are renamed on PRO-MB. The reason is that PRO-MB can be used for the PRO-DBs of the DA1458x family User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 26 of 85... -
Page 27: Da14531 Fcgqfn24 Pro-Db, Default Setup
PRO-MB can be used for the daughterboards of the DA1458x family ● For a detailed description of the connection capabilities of DA14531 FCGQFN24 PRO-DB circuitry, see Appendix D User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 27 of 85... -
Page 28: Table 4: Da14531 Fcgqfn24 Pro-Db And Pro-Mb Signals Assignment (Default)
PWM_2 MBus2 J18:1 P0_9 J8:3-4 P1_0 J2_13 (Default) J1:23-24 P0_10 SW_DIO J1:24 SWDIO (Default) J19:2-3 P3_1 J2:31 INT_2 Arduino J14:2 (Default) P0_11 J8:1-2 P1_3 J2:16 C_TRIG (Default) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 28 of 85... -
Page 29: Pro-Mb Setup
To enable reset on an application, P0_0 must be enabled in both hardware and software. Figure 20: RESET Circuit on DA14531 PRO-MB Figure 21: Reset Pin Assignment on PRO-DBs for FCGQFN24 and WLCSP17 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 29 of 85... -
Page 30: Jtag
P0_1 MISO J1:9-10 (Default) P0_5 P0_3 P0_3 J1:5-6 (Default) P0_0 P0_4 P0_4 Flash Voltage. V_FL J1:1-2 (Default) It is supplied with the voltage rail of V BAT_HIGH User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 30 of 85... -
Page 31: Uart
Clear to Send Data Flash 2-wire or Full UART URTS P2_4 P0_4 P0_4 Request To Send P2_3 P0_3 Single wire UART RxTx Receive and Transmit P2_5 P0_5 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 31 of 85... -
Page 32: Figure 24: Single-Wire Uart For Da14531 Wlcsp17 Pro-Db
Two wires are required to connect UTX and URX to DA14531 PRO-DBs ● Disable SPI data flash by removing jumpers on J1 ● JTAG and Reset can be used User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 32 of 85... -
Page 33: Figure 25: 2-Wire Uart Connectivity
P0_1 Remove jumper J1: 7-8 UCTS J1:11 to J2:24 P2_3 P0_3 P0_3 Remove jumper J1: 9-10 URTS J1:13 to J2:25 P2_4 P0_4 P0_4 Remove jumper J1: 5-6 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 33 of 85... -
Page 34: Push Buttons
SW3 is connected to the SWDIO signal (P0_10 for DA14531 FCGQFN24). Users must enable SW3 on the software ● SW2 is assigned to P0_11 of DA14531 FCGQFN24 (P3_1 of PRO-MB) Figure 27: Miscellaneous Peripherals User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 34 of 85... -
Page 35: User Led (D5) And C-Trig (Software Cursor)
Table 12: Configuration Settings for Miscellaneous Peripherals Signals Function PRO-MB DA14531 PRO-DB Comments Enabled by Jumpers FCGQFN24 WLCSP17 J8:3-4 (Default) P1_0 P0_9 C_TRIG J8:1-2 (Default) P1_3 P0_11 Also assigned to SW2. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 35 of 85... -
Page 36: Mikrobus 2 Interface
The same voltage rail applied to the J17:7 BAT_HIGH pin of DA14531 SoC. BAT_HIGH The voltage provided from the USB J18:7 port, V = 5 V through R305. BUS_HUB User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 36 of 85... -
Page 37: Arduino Interface
INT_2 J14-2 P3_1 P0_11 The same voltage rail applied to J11:4 BAT_HIGH the V pin of DA14531 SoC. BAT_HIGH VBUS_HUB voltage provided from J11:5 the USB port. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 37 of 85... -
Page 38: How To Configure The Power Of Da14531 Dk Pro
On DA14531 PRO DBs (WLCSP17 and FCGQFN24), users must set SW1 to buck position permanently. The power circuit consisting of U2 and SW1 on PRO-DBs is not needed. Figure 30: DA14531 PRO-DB Configuration and DA14531 PRO-MB Jumpers User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 38 of 85... -
Page 39: Battery Operation
On DA14531 DK PRO, the DA14531 system can be supplied from a 3 V coin cell battery, type CR2032. A coin cell battery can be applied to either a PRO-MB or a DA14531 PRO-DB. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 39 of 85... -
Page 40: Enabling Coin Cell Battery On Da14531 Pro-Db
On DA14531 PRO-DB: ensure that no battery is inserted in BT1 (see Figure ● On PRO-MB (see Figure 32, right): ○ Remove the jumper on J9:1-2 and apply a jumper on J9:3-4 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 40 of 85... -
Page 41: Figure 33: Bt1 Position On Pro-Mb (Left). Battery Holder, Bu2032Sm-Bt-Gtr, To Be Soldered (Right)
Solder the battery socket on the solder side (BT1) by using BU2032SM-BT-GTR (see Figure ○ Insert a CR2032 coin cell battery Figure 33: BT1 Position on PRO-MB (Left). Battery Holder, BU2032SM-BT-GTR, to Be Soldered (Right) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 41 of 85... -
Page 42: First Steps With Da14531 Dk Pro
In the following sections, the supported features are detailed for each daughterboard. Configuration of DA14531 DK PRO with a DA14531 FCGQFN24 PRO-DB Figure 34: Default Setup of the DA14531 DK PRO with DA14531 FCGQFN24 PRO-DB User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 42 of 85... - Page 43 Allows the DA14531 to be reset (over JTAG or by using the SW1 push button) ● Sets DA14531 DCDC converter to Buck mode to provide 3.3 V ● Enables the current sensing circuit User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 43 of 85...
-
Page 44: Configuration Of Da14531 Dk Pro With A Da14531 Wlcsp17 Pro-Db
Allows the DA14531 to be reset (over JTAG or by using the SW1 push button) ● Sets DA14531 DCDC converter to Buck mode to provide 3.3 V User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 44 of 85... -
Page 45: Current Measurements
-228 mV rail to allow the output to reach true zero ● Analog multiplexers: the low scale output is presented to the A/D converter with a negative polarity User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 45 of 85... -
Page 46: Power Profiler Of Smartsnippet Toolbox
Figure 37: Current Measurement Presented in Power Profiler of SmartSnippets Toolbox Power Profiler of Smartsnippet Toolbox A user can invoke the Renesas SmartSnippets Toolbox from within the SmartSnippets Studio Welcome page. Alternatively, it can be run directly from the start menu under the section “Dialog SmartSnippets Studio vx.x.xx\Dialog SmartSnippets Toolbox for SmartSnippets Studio vx.x.xx”. -
Page 47: Power Profiler Setup
Power Profiler application in SmartSnippets Toolbox will pop up (Figure 40). 2. Click the Config button in the lower right and check if everything is configured correctly (Figure 41). User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 47 of 85... -
Page 48: Figure 40: Power Profiler Of Smartsnippets Toolbox Main Window
42) and set the max scale of Current1 to 10 mA. Note that this does not affect in any way the accuracy of measurement. It only zooms in the waveform that is shown on the viewer window. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 48 of 85... -
Page 49: Measurements
A/D converter) and then click Start. Figure 43: Free Running Capture A triggered capture can be used for acquiring a single waveform (Figure 44). User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 49 of 85... -
Page 50: Figure 44: Triggered Capture
Note that the Auto Trigger and Auto Stop check boxes under Control on the lower right side must remain deselected. Figure 45: Oscilloscope Option User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 50 of 85... -
Page 51: Power Profiler Software Cursors
2. In the main window of the Power Profiler, click Config and temporarily set the calibration offset to zero (Figure 47). Figure 47: Setting Offset to Zero User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 51 of 85... -
Page 52: Figure 48: Measuring Offset
Notice that the value in the Voltage box is 3 V. This is a typical value used across the industry for comparing Bluetooth LE power measurements. Therefore, the power configuration on DA14531 PRO-MB must be updated accordingly (J5: 2-4). User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 52 of 85... -
Page 53: Accuracy Of Current Measurement Circuit
1.1V boost 1.8V buck 3.3V buck 1,E-02 1,E-03 1,E-04 1,E-05 1,E-06 1,E-06 1,E-05 1,E-04 1,E-03 1,E-02 1,E-01 input current (A) Figure 50: Current Measurement Circuit Response, Indicative Graph User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 53 of 85... -
Page 54: Figure 51: Current Measurement Circuit Inaccuracy, Indicative Graph
DA14531 Development Kit Pro Hardware 1.1V boost 1.8V buck 3.3V buck 1,E-06 1,E-05 1,E-04 1,E-03 1,E-02 1,E-01 input current (A) Figure 51: Current Measurement Circuit Inaccuracy, Indicative Graph User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 54 of 85... -
Page 55: Known Issues
SW3 is enabled on DA145xx DEVKT-P PRO-MB by P1_1. By default, this signal is not driven from DA14531. Consequently, jumper J19:4-5 is not required in DA14531 DK PRO. Figure 53: Disable SW3. Remove Jumper from J19:4-5 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 55 of 85... -
Page 56: Mikrobus Wrong Labels
When the 4-wire UART functionality is used with DA14531 Pro-DB and the reset function is enabled on P0_0, the chip will not boot and still remain in the reset state. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 56 of 85... -
Page 57: Figure 55: Full Uart Configuration - Cts Issue
Disconnect the UCTS jumper and place it after the device has booted and P0_0 has been configured properly by the firmware for the UCTS function ● Assign UCTS to another free GPIO and wire it accordingly User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 57 of 85... -
Page 58: Appendix A Fcgqfn24 Pro-Db: Da14531-00Fxdb-P_(376-04-F2)
UM-B-114 DA14531 Development Kit Pro Hardware Appendix A FCGQFN24 PRO-DB: DA14531-00FXDB-P_(376-04-F2) Schematic Figure 56: Schematic, FCGQFN24, DA14531-00FXDB-P_(376-04-F2) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 58 of 85... -
Page 59: Components Placement
UM-B-114 DA14531 Development Kit Pro Hardware Components Placement Figure 57: Components on Top and Bottom Sides for FCGQFN24, DA14531-00FXDB-P_(376- 04-F2) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 59 of 85... -
Page 60: Appendix B Wlcsp17 Pro-Db: Da14531-00Ogdb-P_(376-05-E)
UM-B-114 DA14531 Development Kit Pro Hardware Appendix B WLCSP17 PRO-DB: DA14531-00OGDB-P_(376-05-E) Schematic Figure 58: Schematic, WLCSP17, DA14531-00OGDB-P_(376-05-E) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 60 of 85... -
Page 61: Components Placement
UM-B-114 DA14531 Development Kit Pro Hardware Components Placement Figure 59: Components on Top and Bottom Sides for WLCSP17, DA14531-00OGDB-P_(376-05- User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 61 of 85... -
Page 62: Appendix C Pro-Mb
UM-B-114 DA14531 Development Kit Pro Hardware Appendix C PRO-MB Schematic Figure 60: DA14531 PRO-MB, Headers, and Connectors User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 62 of 85... -
Page 63: Figure 61: Da14531 Pro-Mb, Current Measurement Circuit
UM-B-114 DA14531 Development Kit Pro Hardware Figure 61: DA14531 PRO-MB, Current Measurement Circuit User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 63 of 85... -
Page 64: Figure 62: Da14531 Pro-Mb, Jtag Mcu
UM-B-114 DA14531 Development Kit Pro Hardware Figure 62: DA14531 PRO-MB, JTAG MCU User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 64 of 85... -
Page 65: Figure 63: Da14531 Pro-Mb, Usb Hub, Usb To Uart Ic, And Power Section
UM-B-114 DA14531 Development Kit Pro Hardware Figure 63: DA14531 PRO-MB, USB Hub, USB to UART IC, and Power Section User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 65 of 85... -
Page 66: Components Placement
UM-B-114 DA14531 Development Kit Pro Hardware Components Placement Figure 64: Components on the Top Side of DA14531 PRO-MB User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 66 of 85... -
Page 67: Appendix D Detailed Description Of Hardware Setup
R15 = 36 Signals Naming MB0_4 R28 = NP On PRO-Motherboard MB0_5 R29 = NP Figure 65: System Configuration for DA14531 DK PRO with a DA14531 WLCSP17 PRO-DB (Default) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 67 of 85... -
Page 68: Da14531 Fcgqfn24 Pro-Db, Gpios Configuration, And R-Matrix
The default setup for the D14531 FCGQFN24 PRO-DB is Reset, JTAG, and SPI data bus (assigned to SPI data flash), single-wire UART, LED, and a Key. Extension ports use multiplexed signals. Figure 66 Table 19 show the resistor matrix for FCGQFN24. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 68 of 85... -
Page 69: Figure 66: System Configuration For Da14531 Dk Pro With A Da14531 Fcgqfn24 Pro-Db (Default)
R11 = NP P3_0 P0_10 P1_3 R18 = 1K MB3_1 R12 = 36 P0_11 P3_1 Figure 66: System Configuration for DA14531 DK PRO with a DA14531 FCGQFN24 PRO-DB (Default) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 69 of 85... -
Page 70: Table 19: Da4531 Fcgqfn24 Pro-Db Default Setup
P2_5 PRO-MB signals P2_6 P2_7 P2_8 P2_9 P3_0 P3_1 UART URTS UCTS MOSI MISO SPI Data Flash SWCLK JTAG SWDIO XT32Kp XTAL32K XT32K RESET BUTTO Other SW_TRI User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 70 of 85... -
Page 71: Appendix E Spi Data Flash, Jtag, And Single-Wire Uart (Default)
R6 = Not pop MB2_5 P2_5 P0_5 SWDIO SWDIO R15 = 36 Signals Naming On PRO-Motherboard Figure 67: System Configuration for DA14531 DK PRO with a DA14531 WLCSP17 PRO-DB (Default) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 71 of 85... -
Page 72: Figure 68: Jumper Settings For Pro-Mb (Marked In Red)
R6, R23, R24, R25, R26, R27, R28, R29, R33, R34, R35, Y2 R14, R15, R19, R20, R21, R22, R30 Figure 68: Jumper Settings for PRO-MB (Marked in Red) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 72 of 85... -
Page 73: Da14531 Fcgqfn24 Pro-Db And Pro-Mb Settings
DA14531 DK PRO, three additional jumpers need to be added (marked in blue in Figure 71): J1:19-20, J10:1 to J1:15, and J10:2 to J1:17. The resistors that are not mounted to FCGQFN24 PRO-DB do not appear in Figure 70. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 73 of 85... -
Page 74: Figure 70: System Configuration For Da14531 Dk Pro With A Da14531 Fcgqfn24 Pro-Db (Default)
R18 = 1K MB3_1 R12 = 36 Signals Naming P0_11 P3_1 On PRO-MB Figure 70: System Configuration for DA14531 DK PRO with a DA14531 FCGQFN24 PRO-DB (Default) User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 74 of 85... -
Page 75: Figure 71: Jumper Settings For Pro-Mb
R8, R9, R10, R12, R14, R16, R17, R26, R27, R28, R29, R33, R34, R18, R35, Y2 R19, R20, R21, R22, R30, R31 Figure 71: Jumper Settings for PRO-MB User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 75 of 85... -
Page 76: Figure 72: Resistor And Jumper Settings For Da14531 Fcgqfn24 Pro-Db
UM-B-114 DA14531 Development Kit Pro Hardware Figure 72: Resistor and Jumper Settings for DA14531 FCGQFN24 PRO-DB User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 76 of 85... -
Page 77: Appendix F Enabling Uart, Jtag And 32.768 Khz Crystal
R1, R2, R3, R6, R7, R8, R9, R10, R4, R5, R11, R13, R15, R19, R20, DA14531-FCGQFN24 R12, R14, R16, R17, R18, R23, R21, R22, R25, R26, R27, R28, R29 R24, R30, R31, Y2 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 77 of 85... -
Page 78: Figure 73: Resistor And Jumper Setting For Pro-Mb (Top) And Da14531 Pro-Dbs (Bottom) To Support 2-Wire Uart, Jtag, And 32.768 Khz Crystal
PRO-MB Jumpers (in Red) WLCSP17 FCGQFN24 Figure 73: Resistor and Jumper Setting for PRO-MB (Top) and DA14531 PRO-DBs (Bottom) to Support 2-Wire UART, JTAG, and 32.768 kHz Crystal User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 78 of 85... -
Page 79: Full Uart And Jtag
R11, R13, R15, R19, R20, R21, R8, R9, R10, R12, R14, R16, R17, R22, R27, R28, R29, R33, R34, R18, R23, R24, R25, R26, R30, R35, Y2 User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 79 of 85... -
Page 80: Figure 74: Resistor And Jumper Setting For Pro-Mb (Top) And Da14531 Pro-Dbs (Bottom) To Support Full Uart And Jtag
DA14531 Development Kit Pro Hardware PRO MB jumpers (in red) WLCSP17 FCGQFN24 Figure 74: Resistor and Jumper Setting for PRO-MB (Top) and DA14531 PRO-DBs (Bottom) to Support Full UART AND JTAG User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 80 of 85... -
Page 81: Appendix G Operating The Dk Pro At 1.5 V (Boost Mode)
Figure 76: Using External Power Supply for 1.5 V Boost Operation Important Notice For Boost Operation For a guaranteed startup, the load on VBAT_HIGH must not exceed 50 μA during system startup/wake-up. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 81 of 85... -
Page 82: Figure 77: Examples Of Spi Flash Power Management Using (Top) Analog Switch (Bottom) Directly
Figure 77: Examples of SPI Flash Power Management Using (Top) Analog Switch (Bottom) Directly GPIO For more information regarding the boost operation and flash and secondary bootloader, see Ref. [3]. User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 82 of 85... -
Page 83: Appendix H Da14531 Pro-Mb Pcba Label
Table 31: Date Code vs SPI Flash Date code SPI Data Flash Before 2117 MX25R2035FZ UIL0 2117 and later AT25DF021A-MAHN-T Figure 78: Label on DA14531 PRO-MB PCBA User Manual Revision 1.7 07-Jun-2023 © 2023 Renesas Electronics CFR0012 83 of 85... -
Page 84: Revision History
Date Description 07-Jun-2023 Added SPI flash AT25DF021A. Added Appendix H. 22-Feb-2022 Document rebranded to Renesas. 07-Jun-2021 Table 15: Typo correction for Buck, Bypass setting 23-Apr-2021 Section 2: References - Added missing URL links Section 4.2.1: replaced broken URL link for SMA connector... - Page 85 RoHS Compliance Renesas Electronics’ suppliers certify that its products are in compliance with the requirements of Directive 2011/65/EU of the European Parliament on the restriction of the use of certain hazardous substances in electrical and electronic equipment. RoHS certificates from our suppliers are available on request.
Need help?
Do you have a question about the Pro DA14531 and is the answer not in the manual?
Questions and answers