Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Specialized Jett 16
Summary of Contents for Specialized Jett 16
- Page 1 ASSEMBLY GUIDE ENGLISH...
-
Page 2: Specialized Bicycle Components
SPECIALIZED BICYCLE COMPONENTS We may occasionally issue updates and addendums to this document. Please periodically check www.specialized.com or contact Rider Care to make sure you have the latest information. 15130 Concord Circle, Morgan Hill, CA 95037 (408) 779-6229 0000168961_UM_R2, 08/21... - Page 3 QR code with your smartphone camera. and keep for reference. You should also read the entire Specialized Bicycle Owner’s Manual (“Owner’s Manual”) because it has additional important general information and instructions S E T U P which you should follow.
-
Page 4: What Is In The Box
Please refer to the written warranty provisions provided with your bicycle, or visit www.specialized.com. A copy is also available at your Authorized Specialized Retailer. 1 . 3 S T R U C T U R A L W E I G H T L I M I T S... - Page 5 Lift the top of the box up and off the base packaging. „ The Jett 16 box opens at the top. Remove any security tape, then pull out the tabs and open the top of the box. Lift the bike and its internal packaging out of...
- Page 6 Fig. 3.3 Fig. 3.2 In the rear packaging tower, pull out the tabs holding the small parts box in place, then Lift and remove the packaging brace. „ „ remove the small parts box. Open the small parts box and remove the manuals, pedals, reflectors, and all the tools „...
- Page 7 Fig. 3.4 In the front packaging tower, lift both the handlebar and interior packaging (1), then slide „ the packaging off of the handlebar (2). Pull the handle bar forward and out of the center packaging tower (3), then lift the center „...
- Page 8 Do not remove Jett 16 models from the rear tower and base packaging until the rest of the assembly steps are completed. The Jett 16 does not come with a kickstand. The packaging will hold the bicycle upright during assembly.
- Page 9 Fig. 3.7 Fig. 3.8 Insert the torque wrench into the bolt head (A) and turn the lever arm clockwise until you „ HOW TO USE THE TORQUE WRENCH feel resistance and the lever arm starts to flex. Two different hex bits are provided with the torque wrench for single-speed Jett models: 4 mm Once the lever arm starts to flex, apply the correct torque to the bolt by turning the lever „...
- Page 10 3.10 1/16th 3/8th 0° 0° 90° 90° 180° 180° Fig. 3.9 Fig. 3.10 Do not touch the wrench gauge faceplate with your fingers when torqueing as this could „ HOW TO USE THE FLAT WRENCH give you a false reading. When using the provided flat wrench, as indicated, use the following general guidelines to achieve proper torque: To properly tighten a bolt without a torque wrench, each bolt or nut must be turned a...
- Page 11 Thread each bolt through the faceplate and into the stem body until they are equally finger- „ Visit specialized.com/setupmyjett to determine the number position the tightened and the upper and lower gaps between the stem body and faceplate are equal handlebar should be set to for the rider.
- Page 12 3.13 3.14 in-lbf Fig. 3.13 Fig. 3.14 In an alternating (cross) pattern, using the supplied torque wrench and 4mm hex bit, Once assembly is complete, double-check to make sure the stem and handlebar are „ „ tighten each faceplate bolt approximately 1/2 turn, then repeat the cross pattern to torque aligned with the front wheel.
- Page 13 A D J U S T I N G T H E S E A T P O S T H E I G H T 3.15 3.16 in-lbf Fig. 3.16 Fig. 3.15 The stem comes pre-installed and aligned. Should you need to adjust the stem, use the Using the 5 mm hex bit, loosen the seat collar bolt.
- Page 14 More pronounced knee bend or moderate space under the heels, while acceptable, can result in less control of the bicycle. Experiment with the saddle height until you find the position that works best for the rider. For more fit recommendations, visit specialized.com/setupmyjett.
- Page 15 I N S T A L L I N G T H E P E D A L S 3.19 3.20 in-lbf Fig. 3.19 Fig. 3.20 Once the preferred height is determined, align the saddle with the centerline of the bicycle, Remove the pedals from their packaging and locate the “L”...
- Page 16 Repeat these steps for the left pedal on the left crank arm (counter-clockwise rotation). „ When adjusting reach, be sure that the lever is not able to touch the grip when the brake is „ applied (C). Your Authorized Specialized Retailer should perform any necessary additional adjustments. „...
- Page 17 I N S T A L L I N G T H E R E F L E C T O R S A D J U S T I N G T H E C R A N K S Both the Jett 20 and 24 multi-speed models have adjustable cranks.
- Page 18 6 mm WARNING! A correctly installed wheel is critical for the rider's safety. If you are unfamiliar with removing (or installing) wheels, contact your Authorized Specialized Retailer. 3.26 Fig. 3.25 Using the 6 mm hex key, remove the crank arm plug (A) from the lower position (B) on the „...
- Page 19 3.27 3.28 3/8th 0° 90° 180° Fig. 3.27 Fig. 3.28 Using the flat wrench, loosen the front wheel axle nuts (A). „ REINSTALLING THE FRONT WHEEL ON MULTI-SPEED MODELS Guide the wheel down and out of the dropouts (B). „ Guide the wheel up and into the fork dropouts and between the brake pads.
- Page 20 (B) from the quick release cradle (C). wobble. If the wheel wobbles and is not centered, please see you Authorized Using the flat wrench, loosen the rear wheel axle nuts. „ Specialized Retailer.
- Page 21 3.31 3.32 Fig. 3.31 Fig. 3.32 Rotate the derailleur down and back to release pressure on the chain. Lift the bicycle and guide the wheel down and out of the dropouts. „ „...
- Page 22 3.33 3.34 3/8th 0° 90° 180° Fig. 3.33 REINSTALLING THE REAR WHEEL ON MULTI-SPEED MODELS Fig. 3.34 With the brake cable disconnected, guide the wheel into the dropouts and between the „ Reconnect the rear brake cable by squeezing the brake arms (A) together and inserting the „...
-
Page 23: Safety Check
Lift the rear end of the bicycle and spin the rear wheel to check if the wheel is centered and „ pump with an accurate gauge. Please refer to the Tires and Tubes section of the Specialized does not wobble.
Need help?
Do you have a question about the Jett 16 and is the answer not in the manual?
Questions and answers