Frames or parts under high stress may fail, causing you to lose control or fall. Because of the risk involved, Specialized recommends that you conduct a thorough inspection before each ride. If you miss a jump, ditch your bike in mid crash, dump or launch your bike without you on it, inspect yourself for injury, then carefully inspect your bicycle for damage.
Page 5
Specialized does not warrant the bicycle frame or components for such activities, and expressly disclaims all warranties, including the warranty of fitness for particular purpose and merchantability.
Page 6
Your bicycle has been engineered and tested with specific components and parts. Because of the great variety in these items, it is impossible for Specialized to test and approve of all possible combinations. Modifying the frame, fork, or any of the components may make your bike unsafe.
FORK / SEAT POST SETUP INFORMATION WARNING! The Stumpjumper frame is compatible ONLY with single crown forks that have travel of 4.72” (120mm) or less. Use of different styled forks or forks with longer travel may result in catastrophic failure of the frame which may result in serious personal injury or death.
REAR SHOCK SETUP Rear Air Shock Setup AFR Brain Fade Sag Setting: Set the sag at to 8% of shock stroke. 0-mm for 6” FSR 8.-mm for 9er FSR. See attached chart for starting air pressure. Note - the chart is only a starting point, actual sag needs to the checked and adjusted on the bike, while riding, and at regular intervals.
Page 13
DERAILLEUR GUARD INSTALLATION The Specialized Derailleur guard is available separately through your local Specialized dealer. The guard works with solid or Q/R axle types and is compatible with all Mountain bike models using the 00-006 Enduro/Demo derailleur hanger. Guard Part #: 9896-400...
Page 14
Specialized recommends the application of carbon assembly compound between the seat tube and post to increase friction. Recommended compounds can be found at www.tacx.com. See your authorized Specialized retailer if you have any questions.
Page 15
HEADSET INSTALLATION / REMOVAL Specialized mtn carbon frames use a 48mm (4.8mm x 8mm x 4°) Campagnolo Standard compatible top and .” (mm x 7mm x 4°) bottom bearing. Ensure that replacement bearings are compatible with the Specialized headset specification. No tools are needed for installation or removal of both bearings.
Page 16
Schematic #20 Seatstay Pivots Stumpjumper Alloy All alloy spacers: Small diameter of spacer facing bearing Hanger bolt Dropout Hanger DROPOUT ASSEMBLY x 2 S-LINK Stumpjumper Carbon Chainstay Bridge Chainstay BOTTOM BRACKET ASSEMBLY UPPER SHOCK ASSEMBLY Alloy frames only Bolts Derailleur Cage Derailleur Cage spacer Derailleur Mount Chainstay...
Page 17
NOTE: Bearing and Bolt Kits are available only through your local Specialized dealer. To retain your warranty and for your safety, all maintenance should be performed by your local Specialized dealer. Part # Qty. Part Description BB Pivot Bearing Dropout Pivot Bearing...
ADDITIONAL CONDITIONS This Limited Warranty is made only to the original owner of this new Specialized bicycle or frameset purchased from an authorized Specialized dealer, and it shall remain in force only as long as the original owner retains ownership of the Specialized bicycle. This Limited Warranty is not transferable. In order to exercise your rights under this limited warranty, the bicycle or frameset must be presented to an authorized Specialized dealer, together with a receipt, bill of sale or other appropriate written proof of purchase which identifies the bicycle or frameset by serial number.
Page 19
USEFUL PRODUCT LIFE CYCLE Every Specialized bicycle and frameset has a useful product life cycle. The length of that useful product life cycle will vary with the construction and materials of the bicycle or frameset, the maintenance and care the bicycle or frameset receives over its useful product life cycle, and the type and amount of use the bicycle or frameset is subject to. Uses in competitive events, trick riding, ramp riding, jumping, aggressive riding, riding on severe terrain, riding in severe climates, riding with heavy loads, commercial activities and other types of non-standard use can dramatically shorten the useful product life cycle of a Specialized bicycle or frameset.
Need help?
Do you have a question about the S-Works Safire and is the answer not in the manual?
Questions and answers