Advertisement
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Specialized Demo 8
Summary of Contents for Specialized Demo 8
- Page 1 OWNER’S MANUAL...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Introduction... Post Setup / Fork Compatibility... Frame Features... Frame Geometry... Shock Setup... Tips... Optional Derailleur Guard Installation... Schematic and Specifications... Warranty... -
Page 4: Introduction
Frames or parts under high stress may fail, causing you to lose control or fall. Because of the risk involved, Specialized recommends that you conduct a thorough inspection before each ride. If you miss a jump, ditch your bike in mid crash, dump or launch your bike without you on it, inspect yourself for injury, then carefully inspect your bicycle for damage. - Page 5 Specialized does not warrant the bicycle frame or components for such activities, and expressly disclaims all warranties, including the warranty of fitness for particular purpose and merchantability.
- Page 6 In order to help minimize the chances of an injury, it is critical for you to have work performed by an authorized Specialized retailer.
-
Page 7: Seat Post Setup
SEAT POST SETUP Minimum Seatpost Insertion Guide Hole SEATPOST MINIMUM INSERTION: All Specialized full suspension models with interrupted seat tubes have a small hole to identify the minimum insertion allowed for your seatpost. If you cannot see the seatpost tube through this hole, your seatpost is too far extended. -
Page 8: Frame Features
DEMO FRAME FEATURES . Main Frame . Seatstay . Chainstay 4. Sub-Seatstay . -Link 6. Main Pivot 7. Dropout (Horst) Pivot 8. -Link at Seatstay Pivot 9. -Link at Frame Pivot 0. Sub-Seatstay Shock Eyelet . Shock / Shuttle Eyelet . -
Page 9: Frame Geometry
DEMO FRAME GEOMETRY 250mm... -
Page 10: Frame Specifications
DEMO 8 FRAME GEOMETRY *Top Tube Length **Standover Height Head Tube Length Head Angle - Steep Head Angle - Slack Seat Angle - Steep Seat Angle - Slack BB Height - High BB Height - Low Wheelbase Chainstay Length * TT length is the Horizontal Measurement from the center-line of the HT at the top of the HT to the center-line of the projected seat tube. - Page 11 DEMO 7 FRAME GEOMETRY *Top Tube Length **Standover Height Head Tube Length Head Angle - Steep Head Angle - Slack Seat Angle - Steep Seat Angle - Slack BB Height - High BB Height - Low Wheelbase Chainstay Length * TT length is the Horizontal Measurement from the center-line of the HT at the top of the HT to the center-line of the projected seat tube. ** Stand Over height is measured vertically at the centerpoint of the TT measurement.
-
Page 12: Shock Setup
- See spring rate chart for additional information or refer to the Fox shock manual. - Recommended sag: 0 - % of shock stroke. Demo 8 sag: mm - 4mm Adjust Rebound: Rebound damping controls the rate at which the shock returns after it has been compressed. -
Page 13: Tips
CAUTION: Normally, the front derailleur cage is positioned 1-3 mm above the large (44t) outer chainring. When using an outer chainring (in place of a bash guard) the design of the Demo 8 & 9 requires that the front derailleur cage be positioned 3-5 mm above the outer chainring to prevent contact. - Page 14 The Specialized Derailleur guard comes with 0/06 Enduro 6” and Demo 8 models, and is available separately through your local Specialized dealer. The guard can be used in Q/R or solid axle setup, and is compatible with all Specialized Mountain bike models using the 00-006 Enduro/Demo derailleur hanger.
- Page 15 DERAILLEUR GUARD INSTALLATION Derailleur Guard Installation (Solid Axle option): . Install rear derailleur on derailleur hanger. . Place rear wheel in frame and install non-drive side nut. . Insert appropriate derailleur guard pin in derailleur. 4. Place guard sleeve in derailleur guard. .
- Page 16 Schematic #19 S-Link Mount Shock Mount Shock Shuttle Washers 16.5x10x0.5mm Shock Shock Shuttle Mount Shuttle Shock Shuttle Bolts M10 x 16mm 115-135 in-lbf Shock reservoir: Always facing down All alloy spacers: Small diameter of spacer facing bearing...
- Page 17 NOTE: Bearing and Bolt Kits are available only through your local Specialized dealer. To retain your warranty and for your safety, all maintenance should be performed by your local Specialized dealer. 2007 DEMO 7 /8 Part # Qty. Part Description...
-
Page 18: Warranty
ADDITIONAL CONDITIONS This Limited Warranty is made only to the original owner of this new Specialized bicycle or frameset purchased from an authorized Specialized dealer, and it shall remain in force only as long as the original owner retains ownership of the Specialized bicycle. This Limited Warranty is not transferable. In order to exercise your rights under this limited warranty, the bicycle or frameset must be presented to an authorized Specialized dealer, together with a receipt, bill of sale or other appropriate written proof of purchase which identifies the bicycle or frameset by serial number. - Page 19 USEFUL PRODUCT LIFE CYCLE Every Specialized bicycle and frameset has a useful product life cycle. The length of that useful product life cycle will vary with the construction and materials of the bicycle or frameset, the maintenance and care the bicycle or frameset receives over its useful product life cycle, and the type and amount of use the bicycle or frameset is subject to. Uses in competitive events, trick riding, ramp riding, jumping, aggressive riding, riding on severe terrain, riding in severe climates, riding with heavy loads, commercial activities and other types of non-standard use can dramatically shorten the useful product life cycle of a Specialized bicycle or frameset.
- Page 22 15130 Concord Circle Morgan Hill, CA 95037 www.specialized.com © 2007 Specialized Bicycles PN# W2070134...
Need help?
Do you have a question about the Demo 8 and is the answer not in the manual?
Questions and answers