Page 2
The products covered by this instruction manual are manufactured and/or sold by Vertiv. This document is the property of Vertiv and contains confidential and proprietary information owned by Vertiv. Any copying, use, or disclosure of it without the written permission of Vertiv is strictly prohibited.
1 Important Safety Instructions Save These Instructions This manual contains important instructions that should be followed during installation of your Vertiv™ Liebert® EXM Parallel Cabinet. WARNING! Risk of moving heavy units and tipping hazard. It can cause damage to the equipment, injury and death.
Page 6
Vertiv™ Liebert® EXM Parallel Cabinet User Manual WARNING! Read this manual thoroughly before working with the Liebert® EXM Parallel Cabinet. Retain this manual for use by installing personnel. Risk of arc flash and electric shock. It can cause damage to the equipment, injury and death.
Vertiv™ Liebert® EXM Parallel Cabinet User Manual 2 Mechanical Installation 2.1 Introduction This chapter describes the requirements that must be taken into account when planning, positioning, and cabling of the Vertiv™ Liebert® EXM Parallel Cabinet. This chapter is a guide to general procedures and practices that must be observed by the installing engineer. The particular conditions of each site will determine the applicability of such procedures.
2.3 Environmental Considerations 2.3.1 Room The Vertiv™ Liebert® EXM Parallel Cabinet is intended for indoor installation and should be located in a cool, dry, clean air environment with adequate ventilation to keep the ambient temperature within the specified operating range (see Specifications on page 31).
2.4.2 Clearances Vertiv™ Liebert® EXM Parallel Cabinet have no ventilation grilles at either side or at the rear. Clearance around the front of the equipment must be sufficient to enable free passage of personnel with the doors fully opened. It is important to leave a distance of 24 in.
If you have any difficulties, do not hesitate to contact Vertiv. See the back page of this manual for contact information. AVERTISSEMENT! Risque de décharge électrique pouvant entraîner des dommages matériels, des blessures et même la mort.
Page 12
5. Tighten the connections to the proper torque (see Table 4.5 on page 34). Ensure correct phasing. 6. Connect the control wiring from the Vertiv™ Liebert® EXM Parallel Cabinet terminal blocks TB1 and TB10 to the Vertiv™ Liebert® EXM UPS Bypass Module (X9, J23, and J26). Tighten the connections to the proper torque (see Table 4.5 on page 34).
Page 13
Vertiv™ Liebert® EXM Parallel Cabinet User Manual Table 2.1 Power Wiring for Vertiv™ Liebert® EXM UPS to Vertiv™ Liebert® EXM Parallel Cabinet System Configuration From Utility UPS 1 AC Input Utility UPS 2 AC Input Utility UPS 1 AC Output Liebert®...
Page 14
Vertiv™ Liebert® EXM Parallel Cabinet User Manual Table 2.1 Power Wiring for Vertiv™ Liebert® EXM UPS to Vertiv™ Liebert® EXM Parallel Cabinet System Configuration From Utility UPS 1 AC Input Utility UPS 2 AC Input Utility UPS 3 AC Input Utility Liebert®...
Page 15
Vertiv™ Liebert® EXM Parallel Cabinet User Manual Table 2.3 Control Wiring for Vertiv™ Liebert® EXM UPS to Vertiv™ Liebert® EXM Parallel Cabinet with SKRU Interlock System Configuration From Liebert® EXM UPS Bypass Module Signal Name UPS 1 X9J23-4 TB7-1 UPS1 On-UPS...
Page 21
The control wiring and the power wiring must be run in the separate conduits. All the wiring is to be in accordance with the national and the local electrical codes. If the maintenance bypass cabinet is attached to the UPS, Vertiv will supply the interconnection cables. 3 Installation Drawings...
Page 22
All the wiring is to be in accordance with the national and the local electrical codes. If the maintenance bypass cabinet is attached to the UPS, Vertiv will supply the interconnection cables. 2+1 available only from 120 kVA to 160 kVA.
Page 23
All wiring is to be in accordance with the national and the local electrical codes. If the maintenance bypass cabinet is attached to the UPS, Vertiv will supply the interconnection cables. 1+1 available from 120 kVA to 200 kVA, 2+0 available from 120 kVA to 160 kVA.
Page 24
Vertiv™ Liebert® EXM Parallel Cabinet User Manual Figure 3.7 Outline Drawing—300 mm Vertiv™ Liebert® EXM Parallel Cabinet Item Description Leveler NOTE: All dimensions are in inches (mm). 24 in. (610 mm) minimum clearance above the unit for air exhaust and 36 in. (914 mm) front access required for service.
Page 25
Vertiv™ Liebert® EXM Parallel Cabinet User Manual Figure 3.8 Outline Drawing—600 mm Vertiv™ Liebert® EXM Parallel Cabinet Item Description Caster Leveler NOTE: 24 in. (610 mm) minimum clearance above the unit for air exhaust and 36 in. (914 mm) front access required for service.
Page 26
Vertiv™ Liebert® EXM Parallel Cabinet User Manual Figure 3.9 Outline Drawing—800 mm Vertiv™ Liebert® EXM Parallel Cabinet Item Description Caster Leveler NOTE: All dimensions are in inches (mm). 24 in. (610 mm) minimum clearance above the unit for air exhaust and 36 in. (914 mm) front access required for service.
Vertiv™ Liebert® EXM Parallel Cabinet User Manual 4 Specifications Table 4.1 Vertiv™ Liebert® EXM Parallel Cabinet Specifications Model Size 10 kVA to 40 kVA 60 kVA to 100 kVA 120 kVA to 200 kVA Cabinet Width 300 mm 600 mm 800 mm...
Vertiv™ Liebert® EXM Parallel Cabinet User Manual Table 4.1 Vertiv™ Liebert® EXM Parallel Cabinet Specifications Model Size 10 kVA to 40 kVA 60 kVA to 100 kVA 120 kVA to 200 kVA Operating Temperature, °F (°C) 32 to 104 (0 to 40) (UPS)
Page 37
Vertiv™ Liebert® EXM Parallel Cabinet User Manual Table 4.3 Liebert® EXM Parallel Cabinet Output Currents, 2+0 and 2+1 Configurations 2+0 and 2+1 Configuration UPS Size in System Nominal Output OCP Device 75 °C Current Copper Aluminum Bolt Size ParalleL Rating...
All electrical connections must be tight. Table 4.5 below and Table 4.6 below provide the torque values for the connections to the Vertiv™ Liebert® EXM Parallel Cabinet. Use these values unless the equipment is labeled otherwise. Table 4.5 Busbar Torque for Power Wiring...
Page 39
Vertiv™ Liebert® EXM Parallel Cabinet User Manual...
Need help?
Do you have a question about the Liebert EXM and is the answer not in the manual?
Questions and answers