Exmark TURF TRACER HYDRO Operator's Manual page 11

ff A
D A N G E R
1
. USE ECkZZ
. or cess si
• X OT CFSA'
. jatch fdk on
. m Rj
• UX 55W
• DRIVE SSY*
•
EOiE TJ^S
• do or ta n
• AVOID SX30EN
XJl'iJi Y-Bi QPSUTIHs y SLKS
ys - OY3 IP AO DCW
£ Qi SITES TEA73 THAN 20'
E*B, HliS. RXKS. RISES, DIPS
K D^P-IFS AO STS5 SA»3
3! 5:F3E SA336
y SL555
SIDYlY
*
T SJjPES
STARTS
Al
y
III
r
. S ALL PSPJ OUT 5 AREA Y-EN fOCKs
. TrOS IE-S7S
S
?JJE CNTAa U» CA12
SocIJJS lK.LRif DR DEATH
—
• d: or opsutc in
AN E0LS3 ASA
. 3GOS PR21IE
OOID: Y-ICH IS AN
[DlfciSS Ear PDIS3N
^
LOCATION: LH and RH Front Top
Surface of Mower Deck
PART NO.
403005
PART NO.
603350
LOCATION: Front Right Corner
of Engine Deck
AWARNING
DO HOT OPERATE WITHOUT
DISCHARGE DEFLECTOR OR
EHTIRE GRASS COUECTIOM
SYSTEM IN PLACE. DO NOT
REMOVE GRASS CATCHER UNTIL
BLADES HAVE STOPPED.
V MWI
PART NO.
Part No. 303508
323525
A CAUTION
1. HEAD OPERATOR'S MAWUAL. BEFORE OPERATING.
2. CLEAR AREA OF PEOPLE. PETS AND
DEBRIS BEFORE MOWING.
2. KEEP RIDERS OFF.
4. BEFORE STARTING ENGINE:
.A. BLADE CLUTCH MUST BE DISENGAGED.
B TRANSMISSION MUST BE W NEUTRAL
C» FOR ELECTRIC START ENGINE,
OPERATOR MUST BE IN OPERATING
POSITION WITH OPERATOR PRESENCE
CONTROL LEVERS DEPRESSED.
D. FOR MANUAL START ENGINE. PLACE
LEFT AND RIGHT DRIVE LEVERS INTO
NEUTRAL LOCK POSITION USING
THUMB LATCHES.
5. BEFORE LEAVING OPERATOR'S POSITION:
A. SHIFT TRANSMISSION TO NEUTRAL
S. DISENGAGE BLADE CLUTCH.
C. SHUT OFF ENGINE and R£*»OVE KEY
OR SPART PLUG CABLE.
•. KEEP ALL SHIELDS AND GUARDS «N PLACE.
7. DO NOT OPERATE MOWER DECK UNLESS
ENTIRE GRASS CATCHER IS IN PLACE.
1. USE CAUTTON ON SLOPES.
I. DO NOT PARK ON SLOPES IX_£SS WHEELS
ARE CHOCKED OR BLOCKED.
YC, SMUT OFF ENG** AND REMOVE KEY AXJ/OR
SPARK PLUG CABLE BEFORE UAK*0
ADJUSTMENTS. S£RV»C*+G OR OJLANP^a
LOCATION:
Upper Handle Console
LOCATION: On Top Rear RH-Surface
of Mower Deck
A
WARNING
OPEN BELT DRIVE
STOP ENGINE BEFORE
REACHING UNDERNEATH
PART NO.
303517
LOCATION:
LH Side of Rear Surface
of Engine Deck
AWARNING
DISENGAGE BLADE CLUTCH. SHUT OFT
ENGINE AND REMOVE KEY BEFORE MAKING
ADJUSTMENTS. SERVICING OR CLEANING DECK.
CUTTING HEIGHT ADJUSTMENT
DECK
SUPPORT PtN
CUTTING
HEIGHT
-UP*)
2.6 (ST)
D-5
M
2.0(7*) INCHES (biiti)
2J{«J
*.0
pH)
*£
pU)
ANTI-SCALP HOLLER
ADJUSTMENT
FOR MAXIMUM DECK FLOTATION,
PLACE ROLLERS IN POSITIONS SHOWN.
CUTTING HEIGHT
INCHES (mm)
\
. I
. 1-5 (3S)
!_ 2-0 (51)
i- 11 (M)
I_ 2.0 (7|)
ROLLERS SHOULD MAINTAIN 1/4* ({.4)
CLEARANCE TO GROUND. DC NOT
ADJUST ROLLERS TO SUPPORT
MOWER DECK. . .
PART NO.
543660
LOCATION: LH Front of Mower
Deck Top Surface
-6-