1. Manuals
  2. Brands
  3. BendPak Manuals
  4. Lifting Systems
  5. 12APX
  6. Installation and operation manual

BendPak 12APX Installation And Operation Manual

Clear floor two-post lifts
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation and Operation Manual
Models:
• 12APX
• 12APX-192
Original instructions in
the English language.
Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.
IMPORTANT Safety Instructions, save these instructions! Read the entire contents of
this manual before using this product. Failure to follow the instructions and safety precautions in this
manual can result in severe injury or death. Make sure all other operators also read this manual. Keep
the manual near the product for future reference. By proceeding with setup and operation,
you agree that you fully understand the contents of this manual and assume full
responsibility for product use.
Clear Floor Two-Post Lifts
Manual P/N 5900374 — Revision A2 — June 2024
⚠
DANGER
30440 Agoura Road
Agoura Hills, CA 91301 USA
Telephone: (805) 933-9970
bendpak.com
12APX Shown

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 12APX and is the answer not in the manual?

Questions and answers

Related Manuals for BendPak 12APX

Summary of Contents for BendPak 12APX

  • Page 1 English language. 12APX Shown ⚠ Designed and engineered by BendPak Inc. in Southern California, USA. Made in China. DANGER IMPORTANT Safety Instructions, save these instructions! Read the entire contents of this manual before using this product. Failure to follow the instructions and safety precautions in this manual can result in severe injury or death.
  • Page 2 Copyright. Copyright ©2024 by BendPak Inc. All rights reserved. You may make copies of this document if you agree that: full attribution goes to BendPak Inc., you are not authorized to make changes to the content, you do not gain any rights to this content, and you will not use the copies for commercial purposes.
  • Page 3 Only use the Lift if it can be used safely! Unit Information. Enter the Model Number, Serial Number, and the Date of Manufacture from the ID label on your unit. This information is required for part or warranty issues. Model: Serial: Date of Manufacture:...

  • Page 4: Table Of Contents

    This manual describes the four BendPak Two-Post Lift models: • 12APX A Two-Post Lift with an overall height of 169 in. (4,294 mm) that raises Vehicles up to 12,000 pounds (4,536 kg). 12APX-192 A taller version of the 12APX with an overall height of 193 in. (4,904 mm), designed •...

  • Page 5: Shipping Information

    Lift at all times. The Lift should only be operated by authorized personnel. Keep children and untrained personnel away from the Lift. 4. BendPak recommends referring to the ANSI/ALI ALIS Standard Safety Requirements for Installation and Service for more information about safely installing, using, and servicing your Lift.
  • Page 6 17. Always wear safety glasses! Everyday glasses only have impact resistant lenses, they are not safety glasses. 18. 12APX Series Lifts are Two-Post Service Lifts. Use them only for their intended purpose. 19. You must wear OSHA-approved (publication 3151) personal protective equipment at all times when installing, using, maintaining, or repairing the Lift.
  • Page 7 BendPak assumes no liability for damages resulting from: • Use of the equipment for purposes other than those described in this manual. • Modifications to the equipment without prior, written permission from BendPak. • Injury or death caused by modifying, disabling, overriding, or removing safety features. •...

  • Page 8: Components

    Components Not all components shown. Models with extensions are taller. Reference only – do not scale. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...

  • Page 9: Specifications

    Specifications Reference only – do not scale. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 10 Lift Arms are measured from the Lift Arm’s axis of rotation to the Frame Cradle Pad mounting pin center. Special voltages available upon request. Specifications subject to change without notice. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...

  • Page 11: Installation Checklist

    Installation Checklist Following are the steps needed to install a 12APX Series Two-Post Lift; perform them in this order. ☐ 1. Review the Safety Rules. ☐ 2. Make sure you have the necessary tools. ☐ 3. Plan for Electrical Work.

  • Page 12: Installation

    Review the Safety Rules When installing a Lift, your safety depends on proper training and thoughtful operation. BendPak recommends referring to the ANSI/ALI ALIS Standard Safety Requirements for Installation and Service for more information about safely installing, using, and servicing your Lift.
  • Page 13 Lift. You can identify the Power Side Post by the Mounting Bracket to which the Power Unit attaches. Refer to the figures below. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 14 When installing the Overhead Assembly, always orient the assembly to place the Limit Switch on the Power Unit side of the Lift. Top View Approach Side Top View Power Unit Opposite Approach 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 15 Figures are not to scale. Not all components shown. Sufficient distance WILL be required on the Front and/or Rear to allow Vehicles to be driven in or backed out from these directions. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 16 Power. You need an appropriate VAC power source for the Lift’s Power Unit. • Outdoor installations.12APX Series Two-Post Lifts are approved for indoor installation and • use only. Outdoor installation is prohibited.
  • Page 17 This position will also make it easier to put the Equalizing Cables into position. 12APX Series Lifts have two Safety Assemblies: one on the Power Side Post (above the Power Unit) and the other on the Off Side Post at the same height.
  • Page 18 Then move the Safety Block to overlap the Latch Support Plate and secure using the Safety Pivot Pin as shown below. Not to scale. Components removed for clarity. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 19 Safety Latch Support Block that is welded inside the Post, as shown next. Attach the Safety Pivot Holder (5700404) to the Power Side Post, as depicted in the next step. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 20 Reference only – do not scale. Connect the Pivot Pin and Safety Pivot Holder using the M8 x 25 Machine Screw through the Power Side Post. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 21 After the Safety Pivot Holder is in place, attach the Safety Release Handle (5761017) as depicted below. Reference only – do not scale. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 22 The two Equalizing Cables are the same length. ⚠ CAUTION BendPak recommends wearing safety gloves when handling the Equalizing Cables. The following graphic provides an overview of the Equalizer Cable routed into position. Not to scale, components removed for clarity.
  • Page 23 Post. Reference only – do not scale. NOTICE Keep the Post Sheave, Sheave Pin, and Bolt nearby; you will be re-installing them soon. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 24 Move both Lift Heads back down to the bottom of each Post. Verify the Cylinder Clamps are secured in place above the Hydraulic Cylinders. Reference only – do not scale. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 25 Do not operate the Lift if the Cylinder Clamps are not secured on the Hydraulic Cylinders. Note: 12APX-192 Series models are supplied with Post Extensions that raise the height of the Posts to allow you to raise taller Vehicles. The Post Extensions are slipped over the top of both Posts and then bolted into place.
  • Page 26 Hydraulic Hoses and Fittings on the Lift, making your new Lift inoperable and unusable. Your Lift is shipped with clean components; however, BendPak strongly recommends that you take secondary precautions and clean all Hydraulic Hoses and Fittings prior to making connections. It is better and less costly to take these extra steps now so that you do not need to take your Lift out of service later to fix issues that could have been prevented at the time of installation.
  • Page 27 Tighten the Fitting into the connector; do not over tighten the Fitting. Allow the 24-hour manufacturer-recommended curing time before pressurizing the system. Identifying Hydraulic Fittings Joint Industry Council (JIC) National Pipe Thread (NPT) 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 28 Always promptly clean any Hydraulic Fluid spills. If a leak is the source of the spill, lockout the Lift to prevent use until the Hydraulic System is repaired. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 29 Route the Hydraulic Hoses It is easier to put some hydraulic components into position before standing up the Posts. All 12APX Series Lifts use three Hydraulic Hoses (Hose C longer on 12APX-192): Lift Model 12APX 12APX 12APX-192 12APX-192 Hose size Part No.
  • Page 30 Carefully coil up and bind the rest of the Long Hydraulic Hose C, then leave it resting at the top of the Off Side Post until later in the installation. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 31 Chalk Line Guides. The Overall Width value is defined as the distance from the back of one base plate to the back of the other base plate. The following illustration shows how to create Chalk Line Guides for a 12APX Series Lift. Top View of the Base Plates. Not all components are shown.
  • Page 32 Concrete or Anchor Bolts do not meet these specifications, it could lead to product damage, Vehicle damage, personal injury, or even loss of life. BendPak Lifts are supplied with installation instructions and concrete fasteners meeting the criteria as prescribed by the latest version of the American National Standard “Automotive Lifts – Safety Requirements for Construction, Testing, and Validation.”...
  • Page 33 Lift Post as it is raised. You must use the appropriate safety gear including safety glasses, dust masks, gloves, steel-toed work boots and heavy work clothes when anchoring the Posts. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 34 Do not rush. Pull the drill out of the hole frequently to remove debris and clear the opening. Do not drill all the way through the Concrete; if you punch completely through the slab, you could compromise the holding strength of the Anchor Bolts. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 35 Vacuum each hole clean. BendPak recommends using a vacuum to get the hole very clean. A wire brush, hand pump, or compressed air may also be used. Make sure to thoroughly clean each hole. Do not ream the hole. Do not make the hole any wider than the drill bit made it.
  • Page 36 85 – 95 pound feet, using a Torque Wrench. ⚠ CAUTION Do not use an impact wrench to torque the Anchor Bolts. Install the Foot Guard on the Power Side Post as shown above. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 37 M12 hardware to secure the other end of the Stop Bar. The Overhead Assembly must be installed to place the Limit Switch closest to the Power Side Post. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 38 Electrician. Leave enough of the 14-2 Cable near the switch and near the Power Unit for the electrician to make the connections. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 39 The Limit Switch Cable exits the Power Side Lift Post below the Safety Release through a cable grommet and is routed to the Power Unit. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 40 NOTICE position before performing the following procedure. When Equalizing Cables are fully routed, they are mirror images of each other. Refer to the following figure for both 12APX and 12APX-192. Components removed for clarity. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 41 At the other Post, remove the Nut from the Threaded End of the other Equalizing Cable. Route the Threaded End over the top of the Overhead Assembly Sheave, and then down the Post towards the Lift Head. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 42 Place the Threaded End of the Equalizing Cable through the hole at the top of the Lift Head, then install the Nut and securely tighten. Reference only – do not scale. Perform Steps 3 through 9 for the other Equalizing Cable. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 43 Retrieve the supplied four M8 Hex Head Bolts, M8 Lock Washers, and one Vibration Dampener. Remove the Power Unit from the packaging material. Important The Power Unit is heavy. BendPak recommends having one person hold the Power Unit while a second person bolts it into place.
  • Page 44 Side Post to the Safety Assembly on the Power Side Post. Not drawn to scale. Some components exaggerated or not shown for clarity. The following illustration shows the Safety Lock Cable connections to the Safety Assemblies. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 45 Equalizing Cables and the Hydraulic Hoses. ⚠ DANGER Verify both the Power Side and the Off Side Safety Assemblies engage properly before operating the Lift. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 46 IMPORTANT! Place a few drops of hydraulic fluid on the Elbow’s O-ring before installing on the Power Unit. There are multiple Ports on the Power Units that are used with 12APX Series Lifts. However, Note: each 12APX Series Lift uses only one Hydraulic Pressure Port (labeled P1 in the drawing below).
  • Page 47 Connect the Straight End of the Long Hydraulic Hose to the -04 JIC connector facing up on the Tee Hydraulic Fitting; finger tighten the connection. Using appropriate tools, go back and securely tighten all finger-tightened connections. Power Ports Location 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 48 Hydraulic Hose Route Components IMPORTANT! Verify all Hydraulic Hoses are seated and secured in the clips on the inside of the Lift Posts and will not interfere with any moving components. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 49 Completed Hose Routing 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 50 Install the Lift Arms The 12APX Lift is delivered with four Lift Arms that are installed, as detailed in the following figures. Observe the Front and Rear sides of the Lift as you have chosen to position them: If you can only drive in one way. The approach side is the Rear, the other side is the Front.
  • Page 51 Lift Head. The Lift Arm openings must be inside the Lift Head and lined up with the holes in the Lift Head. Reference only – do not scale. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 52 Tighten the Set Screw into the groove machined into the Arm Lock Guide Rod. Slide the Arm Lock Pin through the holes in the Lift Head and the Lift Arm Assembly. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 53 Do not operate the Lift if any of the four Lift Arm restraint systems are not functioning correctly. Replace any damaged components with approved replacement parts only. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 54 If your Lift Posts are not straight or your Lift Arms are not level, this is a safety risk. The Vehicles you put on the Lift will be less secure; they could fall and cause injuries or damage to the Vehicle or to the Lift. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 55 The Equalizing Cables will stretch and should be checked weekly for equal tension. Failure to do so will cause uneven lifting. Cables should always be adjusted so that there is equal tension when resting on the safety locks. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 56 – 208 to 230 VAC, circuit, protected by a 30 Amp time delay fuse or circuit breaker for the 5585685 power unit delivered with the Lift. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 57 Lift Posts. ⚠ DANGER All wiring must be performed by a licensed Electrician in accordance with all applicable national and local electrical codes. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 58 (457 mm) above the floor. Never expose the motor to rain or other damp environments; damage to the motor caused by water is not covered by the warranty. Your 12APX Series Lift is available with the following Power Unit: 208-230VAC, 60 Hz, 1 Phase, 5 HP, 23 Amps (5585685) NOTICE 110 VAC Power Units are currently not available for 12APX Series Lifts.
  • Page 59 WARNING Running high electrical current that exceeds the motor’s full load amps (FLA) rating may result in permanent damage to the motor. BendPak strongly recommends you do not exceed the rated duty cycle of the Lift motor. 12APX/12APX-192 Series Two-Post Lifts...
  • Page 60 Power Unit. A quick flip of the switch immediately cuts power to the Lift. On 12APX Series Lifts, the location directly above the Power Unit is used by the Lowering Handle, so your Electrician may want to move the Power Disconnect Switch location up to accommodate.
  • Page 61 • All Cable Sheaves and Cable Sheave Pins • The four inside corners of both Posts • Safety Sheaves • All Lift Arm Pivot Points 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 62 Never raise a Vehicle whose weight exceeds the rated capacity of the Lift. Do not leave the controls until the Lift is engaged on its Safety Locks. Only trained personnel should raise or lower the Lift. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 63 Limit Switch is described to identify and correct the issue. ⚠ CAUTION Do not put the Lift into normal operation until you have confirmed that triggering the Limit Switch stops the Lift Arms from rising. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...

  • Page 64: Operation

    Plugs. Check the Lift for any missing, heavily worn, or damaged parts. Do not operate the Lift if you find any issues; instead, take it out of service, contact your dealer, email support@bendpak.com, or call (800) 253-2363, option 7 then 4.
  • Page 65 Lifts and how to use them safely. ⚠ DANGER Never place any Contact Pads on non-approved, non-load holding Sill Covers or Side Skirts! 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 66 Additional sets are offered to allow you to position the height of the Auxiliary Adapters to make better contact with Vehicles. The 12APX Lift also includes Frame Cradle Adapters — Required for use on Perimeter Frames when lifting trucks, vans or other frame Vehicles that require additional stability.
  • Page 67 Steel Lift Pads — Recommended for additional stability on all vehicles. The flanged edges grip the chassis for an extra-secure hold. (5215692) You may contact BendPak for accessories and replacement Parts information at (800) 253-2363, press option 7, then 5; please have the model and serial number of your Lift available. Visit for additional Adapters and Auxiliary Adapters (also called height adapters or bendpak.com...
  • Page 68 If you are unsure where the Lifting Points are, consult Vehicle Lifting Points for Frame Engaging Lifts, which was provided with the Lift, or the manufacturer of the Vehicle. If you no longer have 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 69 Vehicle Lifting Points for Frame Engaging Lifts, contact BendPak Support email or call (800) 253-2363, option 7, then 4, to secure a replacement support@bendpak.com copy. Some Vehicles may have the manufacturers’ recommended Service Garage Lift Point locations identified by a triangle mark on the underside of the Vehicle, reference SAE J2184- (Current Edition).
  • Page 70 If any of the Adapters are not making solid contact with the Lifting Points, carefully lower the Lift and start over again; the Adapters must make solid contact with all Lifting Points. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 71 Safety Locks at two different heights or only one Safety Lock is engaged, the Vehicle could become unbalanced and fall causing damage, injury, or death. Support the vehicle with Jack Stands in case the vehicle becomes unbalanced while working. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 72 Release Handle and moving; release Lowering Lowering Handle. Handle when Lift stops. Only leave Lift on Safety Locks or fully lowered. Only leave Lift on Safety Locks or fully lowered. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 73 Lock on one Post engaged but the Safety Lock on the other Post not engaged. Safety Lock positions are created by the Safety Lock Weldments, on the back of each Lift Head. Passing: Between Weldments: Engaged: 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 74 Lift raised but not engaged on Safety Locks, the Vehicle is not secure. It could fall, possibly damaging the Vehicle, the Lift, and injuring anyone under the Vehicle. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...

  • Page 75: Maintenance

    Unless stated otherwise, all maintenance may be performed by the owner/employer and does not require trained lift service personnel. Replace worn, damaged or broken parts with original BendPak or BendPak approved parts or with parts that meet or exceed the original specifications.
  • Page 76 Carefully check the Equalizing Cables for signs of damage or extreme wear. See Wire Rope Inspection and Maintenance for additional information. If the Lift becomes inoperative in a raised position, refer to the Troubleshooting section. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 77 1. Relax respective cables, as outlined above. 2. Unscrew Sheave Pin Bolt. 3. Remove Sheave Pin. 4. Apply Red Lithium Grease to Sheave Pin. 5. Reassemble and tighten. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 78 12APX Wire Rope Inspection and Maintenance The 12APX Equalizing Cables should be inspected regularly: • Cables should be replaced when there are visible signs of damage or extreme wear. Do not use the Lift if it has damaged or worn cables.
  • Page 79 Torque Chart 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...

  • Page 80: Troubleshooting

    If your Lift is not functioning correctly, you must take it out of service until it is repaired. Important: Replace worn, damaged or broken parts with original BendPak or BendPak approved parts or with parts that meet or exceed the original manufacturer specifications.
  • Page 81 4. When the Lift heads are on the ground and the Lift is in a safe condition, remove power from the Lift and replace the Safety Cable. Reference only – do not scale. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 82 Washers, or a backing nut (not supplied) may be used to extend the contact point of the Arm Lock Pins. Adjust the Bolt head position to disengage the Lock as required. Refer to the figure below. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 83 If you are unable to find an appropriate facility, the website earth911.com has resources that may be of help. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...

  • Page 84: Wiring Diagrams

    Inspect to verify no stray wire strands are bridging across the terminals. If strands are bridging, correct before proceeding. Replace the Switch Cover and secure with the three screws removed in step 1. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 85 These components must be supplied and installed by a licensed Electrician in accordance with the National Electrical Code (NEC). The Thermal Disconnect while not an NEC requirement may be required by local electrical code. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 86 Normally Closed Terminals on each switch. Refer to the figure below. Inspect to verify no stray or broken wire strands are bridging across the terminals. Replace the Switch Covers and secure with the three screws removed in step 1. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 87 Secure the switches to the bracket on the Overhead assembly. Refer to the figures below Wiring removed for clarity. Attach the 3-Phase Limit Switches to the Lift’s Overhead Assembly using the fasteners described below. Components removed for clarity. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 88 All wiring must be performed by a licensed Electrician in accordance with all local and national electrical codes. Make sure that main electrical power has been disconnected from the Lift and cannot be re-energized until all procedures are complete. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 89 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...

  • Page 90: Labels

    Labels PN 5905940 PN 5905311 PN 5905177 PN 5906087 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 91 PN 5905109 Label Kit 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 92 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 93 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...

  • Page 94: Parts Drawings

    Parts Drawings Model: 12APX 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 95 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 96 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 97 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 98 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 99 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 100 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 101 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 102 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 103 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 104 Model: 12APX-192 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 105 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 106 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...

  • Page 107: Ali Store

    The ALI Store is your trusted source for workplace safety! Visit today and get the training and materials you need to work safely: www.autolift.org/ali-store/. 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...

  • Page 108: Maintenance Log

    Maintenance Log 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 109 Maintenance Log 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 110 Maintenance Log 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 111 Maintenance Log 12APX/12APX-192 Series Two-Post Lifts P/N 5900374 — Rev. A2 — June 2024...
  • Page 112 30440 Agoura Rd. Agoura Hills, CA 91301 USA bendpak.com © 2024 by BendPak Inc. All rights reserved.

This manual is also suitable for:

12apx-192

Table of Contents