Download Print this page
Ulvac OMI-100 Instruction Manual

Ulvac OMI-100 Instruction Manual

Oil mist trap

Advertisement

Quick Links

No.90600-2-02-6
MODEL NO OMI-100/OMI-200
OIL MIST TRAP
INSTRUCTION MANUAL
Before using the product, be sure to read this manual.
Keep this manual in a place where it can be referred
to at any time and look after it carefully.
The contents of this instruction manual are subject to
change without prior notice due to improvements in
performance and the functions of the product.
ULVAC KIKO,Inc.
MIYAZAKI, JAPAN

Advertisement

loading
Need help?

Need help?

Do you have a question about the OMI-100 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Ulvac OMI-100

  • Page 1 No.90600-2-02-6 MODEL NO OMI-100/OMI-200 OIL MIST TRAP INSTRUCTION MANUAL Before using the product, be sure to read this manual. Keep this manual in a place where it can be referred to at any time and look after it carefully. The contents of this instruction manual are subject to change without prior notice due to improvements in performance and the functions of the product.
  • Page 2: Introduction

    The maximum flow rate is 120 L/min for the OMI-100 and 240 L/min for the OMI-200. No part of this manual may be reproduced for use by a third party without written consent by ULVAC KIKO.
  • Page 3: Table Of Contents

    1.1 Danger Inherent to This Unit and Safety Measures ......1 (4) Is any part off position? 1.1.1 DANGER Hazardous gas, hazardous material..... 1 If any problem is found, contact your local ULVAC KIKO representative. 2. OVERVIEW OF OIL MIST TRAP............1 0.4.2 Storage, installation and environmental conditions during operation 2.1 Design Basis..................
  • Page 4: For Safe Operation

    2. OVERVIEW OF OIL MIST TRAP Design Basis The Model OMI-100/OMI-200 oil mist trap separates oil mist discharged from an oil rotary pump during operation to reduce the discharge of oil mist. The oil that has collected in the oil mist trap is returned into the pump case. Being small in size, light in weight, and simple in structure, the unit can be easily maintained and repaired.
  • Page 5: Installing The Unit On Ulvac Kiko Vacuum Pump

    The unit may be ruptured if the maximum flow rate of the unit is exceeded. The Please turn a top cover to the left, remove it and attach a hose nipple for the maximum flow rate for the OMI-100 is 120 L/min and that for the OMI-200 is 240 L/min.
  • Page 6: Inspection And Maintenance

    DANGER taking apart and cleaning maintaining a performance. For disassembly, contact your local ULVAC KIKO representative. If the vacuum pump is used to pump toxic gas, pump oil as well as oil mist trap will NOTE be toxic.
  • Page 7: Troubleshooting

    40 Pa (for 10 (6) OMI-100 : Put a gasket B on a middle board and carry an element retainer on minutes). it. Insert a bolt which attached a gasket A from the hole of element...
  • Page 8: Disposal

    (2) If any trouble occurs under normal operating conditions due to defects in material or workmanship within the warranty period, ULVAC KIKO will correct it free of charge. Normal operating conditions are as follows. Ambient temperature, relative humidity: 7℃~ 40℃, 85% RH or less Type and temperature of exhaust gas from vacuum pump: Dry air or dry nitrogen, 7°C to 40°C...
  • Page 9 ULVAC KIKO , Inc. Head office 291-7 Chausubaru Saito-city,Miyazaki 881-0037 Japan Tel:+81-983-42-1411 Fax:+81-983-42-1422 Sales division 1-10-4 Kitashinyokohama Kohoku-ku Yokohama-city,Kanagawa 223-0059 Japan Tel: +81-45-533-0206 Fax: +81-45-533-0204 Fig. 3 Exploded view for OMI-200 -11-...

This manual is also suitable for:

Omi-200