Related Manuals for Tamarack Solar Flush Mount
Summary of Contents for Tamarack Solar Flush Mount
- Page 1 Flush Mount Installation Manual Roof Series Tamarack Flush Mount Solar Roof Mount System Installation Manual Rev 5 Tech Support: support@tamaracksolar.com / 1-800-819-7236 Ext 556...
- Page 2 Flush Mount Installation Manual Roof Series Table of Contents Installation Features & Ratings System Components Tools Required & Torque Specifications Attaching Rail Mounts & Installing Rails Leveling Rails & Grounding Ground Wiring Diagrams 8 - 9 Module Level Power Electronics (MLPE) Install & Wire Management Module Installation Channel End Clamps &...
- Page 3 • Sleek low-profile design eliminates need for an array skirt Tamarack Product Summary Flush mount is a visually appealing, low profile, photovoltaic (PV) module installation system that significantly lowers PV module installation cost by allowing installation professional to stock fewer parts and to complete...
- Page 4 Flush Mount Installation Manual Roof Series Tamarack Flush Mount System Components 2.3 inch and 1.6 inch Rail Rail Mount and L-Foot Channel End Clamp 50-50 Clamp Bonding Splice Wire Management Clip Rail Ground Lug MLPE Adapter Rail End Cap support@tamaracksolar.com...
- Page 5 Flush Mount Installation Manual Roof Series Tools Required • Cordless Drill • Torque Wrench • Rachet and 1/2” Socket • Level Torque Specifications Rail Mount with 5/16-inch bolt ....... 12 ft-lbs MLPE Rail Attachment .
- Page 6 Flush Mount Installation Manual Roof Series Attach Rail Mounts Each Rail-Mount consists of two parts: a 5/16 inch bolt and a clamp extrusion The rail adapters have been designed to interface with off-the- shelf mounting products that have vertical leveling slots Our Rail Mounts...
- Page 7 Flush Mount Installation Manual Roof Series Leveling Rails Start by leveling the bottom rail of array first Set Rail Adapters near the middle of the leveling range and adjust as necessary to have visually level rails Tighten attachment bolts to the specified torque when aligned...
- Page 8 Flush Mount Installation Manual Roof Series Grounding Diagrams Rail Grounding Method Frame Grounding Method support@tamaracksolar.com 1-800-819-7236 Ext 556 PAGE...
- Page 9 Flush Mount Installation Manual Roof Series Rail Grounding Method with SolarEdge Optimizers Frame Grounding Method with SolarEdge Optimizers support@tamaracksolar.com 1-800-819-7236 Ext 556 PAGE...
- Page 10 Flush Mount Installation Manual Roof Series Module Level Power Electronics (MLPE) Use Tamarack MLPE Rail Adapters to attach Enphase microinverters or SolarEdge Optimizers to the rails The large flat washer is installed between the mounting plate of the MLPE and the top of the rail Tighten bolt with a 1/2”...
- Page 11 Flush Mount Installation Manual Roof Series Module Installation Start module installation at one end of rails If there are multiple rows, start on bottom row Install a 50-50 clamp at end of each rail with the side of clamp with 2 bonding pins, on the module frame...
- Page 12 Flush Mount Installation Manual Roof Series Channel End Clamps Channel End Clamps may be used in place of the 50-50 clamps at ends of rails Channel Clamps secure module frame from below and allow rails to be cut flush to the edge of the ar-...
- Page 13 Flush Mount Installation Manual Roof Series Disclaimer This manual describes proper installation procedures and provides necessary standards re- quired for product reliability Warranty details are available on our website www tamarackso- lar com All installers must thoroughly read this manual and have a clear understanding of installation...
- Page 14 Flush Mount Installation Manual Roof Series Certified Module List for UL2703 Listing Program Manufacturer Model Aleo P18/P19/S18/S19/S59/S79. AU Optronics PM Series modules with 30, 35, 40, and 45 mm frames aaSMbbyyC/zz-xxx Where “aa” can be CH or A; "bb" can be 60, 66, or 72; “yy” can be blank, 10 or Astronergy 12;...
- Page 15 Flush Mount Installation Manual Roof Series Certified Module List for UL2703 Listing Program Manufacturer Model D6M and D6P 30 mm frames EVPVxxxA, Where “A” can be blank or KPanasonic modules with 35 and 40 mm frames VBHNxxxYYzzA Where “YY” can be Panasonic either KA, RA, SA or ZA; “zz” can be either 01, 02, 03, 04, 06, 06B, 11, 11B, 15, 15B, 16, 16B, 17, or 18; and “A” can be blank, E, G, or N Peimar 40 mm frames SbxxxYzz Where “b”...
Need help?
Do you have a question about the Flush Mount and is the answer not in the manual?
Questions and answers