Subscribe to Our Youtube Channel
Related Manuals for Tamarack Solar UNI-SP/01XH
Summary of Contents for Tamarack Solar UNI-SP/01XH
- Page 1 Installation Manual UNI-SP/01XH Installation Manual 2019 Edition v1.02 UNI-SPXH-MAN For model: UNI-SP/01XH...
-
Page 2: Table Of Contents
Warranty Information ........................... 10 Introduction The UNI-SP/01XH Side of Pole Mount is a simple and universal pole mounting solution for PV modules with an area of less than 7 square feet. With its user-adjustable angle settings, the Side of Pole Mount can support installations in a wide range of locations. -
Page 3: Components List
Installation Manual UNI-SP/01XH ITEM PART NUMBER DESCRIPTION 51-3517-242 rev E Bucket, 35.6" 51-3517-243 Clip, left end. 51-3517-244 Clip, right end. 51-0527-000 Rail, panel support 27.5" Components List 51-3517-203 Bucket, low er knee brace 51-3517-207 Channel inner 19" X 1" 51-3517-208 Channel outer 19"... -
Page 4: Optional Components
Installation Manual UNI-SP/01XH Optional Components For mounting (Not included) Depending on mounting surface: (for the upper bucket) 1 Pair of 1/2-13 U-bolts for 2”,3”,4” pipe sizes 2 sets of ½” lag bolts and washers. (For lower bucket) 2 sets of 1/4" lag bolts and washers Step 1. -
Page 5: Step 2. Mounting Rail Supports On Pv Module
Installation Manual UNI-SP/01XH Step 2. Mounting Rail Supports on PV Module Review the reference diagrams to determine the orientation of the panel support rails (facing in or out) and the end clips (facing in or out), based on the center to center range of your module. -
Page 6: Step 3. Attaching Clips To Rails
Installation Manual UNI-SP/01XH Step 3. Attaching Clips to Rails Attach the clips to the rails as determined by the bucket range diagrams (shown in previous step). Example shown has the clips facing in on the inside of the rails that are facing out. -
Page 7: Step 4. Attaching Bucket To Pole
Installation Manual UNI-SP/01XH Step 4. Attaching Bucket to Pole Un-screw the hose clamp to release the end and thread each hose clamp through one of the sets of narrow center slots in SOLID SECTION the bucket(s) as shown and place at the desired location on the pole NOTE: KEEP THE SOLID SECTION OF THE CLAMP CROSSING OVER BOTH SLOTS. -
Page 8: Step 5. Mounting Pv Assembly On Pole
Installation Manual UNI-SP/01XH Step 5. Mounting PV Assembly on Pole A. Place the PV module assembly so the holes on the clips line up with holes in the inside of the bucket. Depending on the size of the panel you started with, your assembly may look different than what is shown in the provided view, with the clips and rails facing in the opposite direction. -
Page 9: Step 6. Attaching Swivel Bracket To Panel Support
Installation Manual UNI-SP/01XH Step 6. Attaching Swivel Bracket to Panel Support A. Using a 1/4-20 x 3/4” bolt and flat washer, attach the bracket to the inside end of the panel support in the hole as shown. B. Repeat on the opposite panel support, leave brackets “finger tight” for final adjustment of the knee brace assembly. -
Page 10: Step 8. Attaching Inner\Outer Brace Channels
Installation Manual UNI-SP/01XH Step 8. Attaching Inner\outer Brace Channels A. Loosely attach the outer channel to the Knee bucket as shown. B. Loosely attach the inner channel to the swivel bracket as shown. C. Align the inner channel inside the outer channel and align the holes to install the bolts. -
Page 11: Installer Responsibility
Refurbished Mounting Structures may be used to repair or replace the Mounting Structures. Tamarack Solar shall have no liability for any injuries or damages to persons or property resulting from any cause, whatsoever, or any claims or demands brought against Tamarack Solar by Purchaser, any employee of Purchaser, client of Purchaser, end-user of the Product or other party, even if Tamarack Solar has been advised of the possibility of such claims or demands (collectively, “Third Party Claims”).
Need help?
Do you have a question about the UNI-SP/01XH and is the answer not in the manual?
Questions and answers