Limited Warranty Customer Support Tamarack Solar makes every effort to ensure your mounting kit is easy to install. If you need assistance at any point in your installation or have suggestions on how we can improve your experience, call customer support at 1-800-819-7236 ext 556 or email us at support@tamaracksolar com Technical Support: 707-234-8107 or www.support@tamaracksolar.com...
Built-in wire management for module and microinverter cables Tamarack Product Summary The Tamarack Solar Ground Mount system is a visually appealing photovoltaic (PV) module installation system that significantly lowers PV module installation cost by allowing the installation professional to stock fewer parts and to complete the installation in less time.
• We recommend consulting with your local building department about local regulations and building require- ments, including soil conditions, terrain, and wind and snow load requirements. Local conditions and • Use only Tamarack Solar Products parts or parts approved by Tamarack; substituting parts may void any applicable warranty.
Tamarack Ground Mount System Components 3.1 inch Rail Rail Splice Pipe Mount Socket Tee Swivel Tee MLPE Adapter Ground Lug 5050 Clamp Module Lead Clip Rail End Cap 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
Exposure Category B is an urban, suburban or wooded area. Obstructions the size of single family dwellings must surround the structure at within 2,630 ft or 10 times the mounting structure height in all directions, whichever is greater. 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
This information will be in the Engineering and Parts List tab in our online tool Use Our Online Tool to Design Your Ground Mount https://tamarack-configurators.cloudapps.ltd/ground-mount/ Tool Details are on the following page. 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
3 Modules per Column with 0 vertical Poles 90798-A 4 Modules per Column with 4 vertical Poles 90804-A 4 Modules per Column with 2 vertical Poles 90842-A 4 Modules per Column with 0 vertical Poles 89778 2-inch Swivel Tee-Fitting 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
Page 10
Re-install the layout strings to make sure that the holes are excavated at the proper locations and adjust the hole centers if necessary. Clean out as much loose soil as you can from the augured holes. 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
Page 11
X-Braces. If the horizontal beams are long, you can do this in sections for easier handling. Check for array tilt 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
Page 12
Make any horizontal adjustments to the Socket Tees required to center the vertical pipe in the holes. Do a final check to make sure that the horizontal beams are level and properly located at the correct spacing between each other, and that the posts are plumb and centered in the holes. 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
Page 13
Repeat this whole process for installing the cross braces on eachnorth/south pair of posts. There may need to be changes to the lengths of the brace pipes from location to location, especially if the installation site is not completely level. 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
Page 14
3 Modules per Column 4 Modules per Column 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
Tighten the U-bolt nuts to 72 inch-pounds (6 foot-pounds) and the flange bolts on the rail clamps to 144 inch-pounds (12 foot-pounds) on all rail assemblies. Attach Pipe Mount to Rail 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
The Socket Tees provide a grounding path between all connected sections of pipe. Because all of the elements of an entire unified ground mount array are bonded electrically, the Tamarack Solar Ground Mount only requires a single Ground Lug for the grounding connection.
Place the second module on the rails, align it with the first module, and slide down and fully into the two mid- clamps. Tighten the mid-clamp bolts to 144 inch-pounds (12 foot-pounds) to fully secure the module. 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
Module Compatability The solar modules listed on the next two pages have been certified to meet UL 2703 standards when installed with a Tamarack Solar FM Rail System. Back View 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
Page 19
1J, 4J, 4S, 5K, 5T, 60, 6J, 6S, 6W, 8K, 8T, or 9S Mitsubishi modules with 46 mm frames - PV-MYYxxxZZ Where "YY" can be LE or JE; and "ZZ" can be either HD, HD2, or FB Mitsubishi 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
Page 20
35 and 40 mm frames Wsy-xxxZa Where "y" can be either P or T; "Z" can be either M, P, or MX; and "a" can be blank or 6 Certified Power Optimizer List for UL2703 Listing Program Manufacturer Model Enphase M250‐72, 250‐60, M215‐60, C250‐72, S230, S280, IQ 6, IQ 6+, IQ 7, IQ 7+, IQ 7X, Q Aggregator Solar Edge P300, P320, P340, P370, P400, P405, P505, P600, P700, P730, P800p, P800s, P850, P860 2024 TAMARACK SOLAR Rev 4X-93 GROUND MOUNT KITS...
Limitation of liability Except as set forth above, Tamarack Solar Products sells the products on an “as is” basis, which may not be free of errors or defects, and all express or implied representations and warranties, including any warranties of merchantability, fitness for a particular purpose, or arising from a course of dealing, course of performance, or trade practice, are hereby disclaimed.
Need help?
Do you have a question about the GM-KITS-MAN and is the answer not in the manual?
Questions and answers