Brita MAXTRA PRO - Water Filtration Systems Manual

Also See for MAXTRA PRO:

Instructions for use manual (156 pages)

Instructions for use manual (15 pages)

Instructions for use manual (33 pages)

Table of Contents

Contents

1 Introduction
2 Parts & Assembly
3 Operation – very easy
4 Documents / Resources
- 4.1 References
- 4.2 Download manual

Brita MAXTRA PRO - Water Filtration Systems Manual

Introduction

The MAXTRA PRO with our unique BRITA MicroFlow technology:
Super-fine mesh captures coarse particles from old pipeworks and the additional high-performance filter mesh retains even the finest* particles (*≥ 30 µm) from tap water.

Powerful Ion-exchange pearls

for softer water, to protect your appliances*
for the reduction of metals such as lead and copper

Natural MicroCarbon from coconut shells

reduces odor- and taste-impairing substances such as chlorine
provides great- tasting, freshly filtered water*

The maximum lifespan of a MAXTRA PRO water filter is 150 litres or 4 weeks.

Acting sustainably is especially important to us

That's why our water filters are recyclable.
Find out more at brita.net

Optimum filter performance

Please only filter cold tap water.
Please only use BRITA water filters with tap water from municipal water treatment plants – only this meets the legal requirements for drinking water quality.

store filtered water in a cool place and use within 24 hours.

Official advice for boiling tap water also applies to BRITA filtered water. The rule is: filter first, then boil!
If this advice no longer applies, please clean the jug thoroughly and insert a new water filter.
For certain groups of people (e.g. babies and people with impaired immunity) it is generally recommended that tap water should be boiled.

Highest quality & hygiene

Over 50 years of water filter experience stands for:

Innovation
the highest quality

In order to meet our high quality standards, there are strict internal and external quality controls in place.
Every MAXTRA PRO water filter undergoes treatment with hot steam for hygiene purposes during manufacture and is then packed in a protective foil. (Note: the water filter may be damp due to condensation following the steam treatment).
The filter material of the MAXTRA PRO water filter undergoes a special treatment with silver for hygiene reasons.
A small quantity of silver may be released into the water. This is in line with the recommendations of the World Health Organization (WHO).
BRITA recommends replacing the water filter regularly.
Please follow the recommended cleaning procedures and advice on preparing the filter. The jug should be cleaned regularly.

warning Note:
If the jug is not being used for a while, remove the water filter, empty the jug and replace the water filter loosely in the empty funnel.
Please refer to "Changing the MAXTRA PRO water filter" chapter.

Parts & Assembly

Water filter exchange indicator
Lid
MAXTRA PRO water filter
Funnel
Jug / Tank
Silicone sealing ring
Tap spout

Operation – very easy

Clean before the first use and every time you change the water filter

For optimum cleaning results, turn the BRITA PerfectFit funnel upside down and flush the BRITA PerfectFit mechanism with tap water for a few seconds (excluding BRITA Flow). The jug should be cleaned before the first use and when you change the water filter – the funnel and jug are dishwasher safe (max. 50°C) or can be cleaned by hand! Please clean your BRITA Flow only by hand with cold or lukewarm water.

Glass Jug: In general, the Glass Jug sealing rings are dishwasher proof, but we still recommend washing them by hand. Otherwise, slight discolouration may occur. Dry it thoroughly before reattaching it to the funnel.

Lid with BRITA Smart Light

Please remove the BRITA Smart Light before cleaning the lid (turn counter-clockwise (x)).
The BRlTA Smart Light must not be washed in the dishwasher! Remove the BRITA Smart Light by hand and clean with a soft, damp cloth.

Lid with non-removable BRITA Memo

Please clean the lid by hand, as it is not dishwasher safe!

Preparing the MAXTRA PRO water filter

Fill the clean jug with cold water.
Immerse the water filter and shake slightly to remove any excess air. Remove the water filter and pour away the water in the jug.

Done!

Inserting the MAXTRA PRO water filter

The BRITA PerfectFit System has been developed to create a perfect fit and seal between the MAXTRA PRO water filter and the funnel.
Insert the funnel into the jug and place the water filter firmly in the funnel. Please push the water filter further downwards if the water does not flow through. BRITA can only guarantee optimum filtration if BRITA MAXTRA PRO water filters are used. The BRITA PerfectFit System is not included in BRITA Flow.

Filling the BRITA water filter jug

The water in the funnel is filtered automatically and flows into the jug.
How the jug is filled will depend on the model or the type of lid.

Activating the MAXTRA PRO water filter

For optimal taste and performance please allow two full funnels of tap water to pass through the filter before drinking.
To join BRITA in considering the environment, you can use this filtered water to water your plants, for example.

Setting the water filter exchange indicator

How handy! The BRITA water filter jug will tell you when you need a new water filter.
There are different exchange indicators for this in the lid:

BRITA Smart Light

Its intelligent sensor not only measures the time since the water filter was last replaced, but also records the volume of filtered water.

Before using the jug for the first time (and after every time you change the water filter), press the BRITA Smart Light reset button for approx. 5-10 seconds until the LED indicator flashes green three times.

The jug is now ready to use.

The flashing light indicates when you should replace the filter:
Green: The water filter is filtering optimally.
Yellow: It will soon be time to change the water filter. Think about purchasing a new one!
Red: Please change the water filter!

You can check your filter status at any time by pressing briefly on the BRITA Smart Light.

BRITA Memo

Remove the protective foil before using BRITA Memo for the first time.
After activating the water filter, press and hold the „START" button until four bars appear on the display and flash twice.
The flashing dot in the bottom right of the display unit means:
"Memo in operation".
A new water filter is required if the empty display unit flashes.

Changing the MAXTRA PRO water filter

Simply remove the water filter and follow steps 1 to 6 of the instructions.

Never place the BRITA water filter jug and the MAXTRA PRO water filter in full sun and keep away from heating elements (e.g. kettles or conventional ovens). It is better to store them in a dark, cool and dry place (and keep new water filters in their original packaging). Store the BRITA Smart Light out of the reach of children (risk of swallowing)!

Sensitive to potassium?
Filtering initially causes a slight elevation in the potassium content of the water. This is harmless (e.g. 1 L of BRITA filtered water contains less potassium than an apple).
Please consult your doctor before using a BRITA water filter if you suffer from kidney disease or have to follow a special lowpotassium diet.

Natural traces
The BRITA activated carbon beads are of natural origin and so natural variations may occur.
A low volume of small carbon particles can get into the filtered water, which you may see as black particles.
These particles are not harmful to your health because they pass naturally through the body unchanged if swallowed.
If you discover carbon particles in your filtered water, BRITA recommends rinsing the water filter until there are no more particles visible.

BRITA Smart Light
Rotate counter-clockwise and remove from the lid.

BRITA Memo
Lift out using a screwdriver (please only remove it for the purpose of disposal).

BRITA water filter jug and water filter
Dispose of these in accordance with the local regulations.

Sustainability is important to us:
We will be happy to supply you with spare parts to extend the lifecycle of our products.
Please contact the BRITA customer services or your local distributor if you have any questions about spare parts.

Exclusion of liability
We ask for your understanding that BRITA does not accept any liability if the information in the usage instructions is not followed.

Do you have any further questions?
Then visit us on brita.net

* This water filter system is tested for lead, copper, chlorine and carbonate hardness according to DIN EN 17093:2018 (limescale is certified to be reduced for 120L).