Table of Contents
Advertisement
Quick Links
Enclosed Switches
ZE/ZV/XE/XV
Long Service Life and Large Breaking Power
• ZE, ZV, and ZV2 incorporate Model Z Basic Switches with rug-
ged diecast cases.
• Available with various models of built-in switches (including split
contact model, maintained operation type, magnetic blowout
model) and various actuators.
Model Number Structure
■ Model Number Legend
@@-@-2@
1 2
3
4
1. Built-in Switch
Z:
SPDT (AC)
X:
SPDT (DC)
2. Mounting Direction
E:
Side mounting
V:
Base mounting
V2:
Diagonal side mounting
3. Actuator
Q:
Plunger
Q22:
Roller plunger
Q21:
Crossroller plunger
QA2:
Roller arm lever
QA277: One-way action roller arm lever
N:
Sealed plunger
N22:
Sealed roller plunger (ZE, ZV, ZV2 only)
N21:
Sealed crossroller plunger (ZE, ZV, ZV2 only)
NA2:
Sealed roller arm lever
NA277: Sealed one-way action roller arm lever
4. Conduit/Ground Terminal
1
None: G
/
/without ground terminal
2
1
G1:
G
/
/with ground terminal
2
G:
Pg13.5/with ground terminal
1
SG1:
/
-14NPSM/with ground terminal
2
YG1: M20/with ground terminal
1
S:
/
-14NPSM/without ground terminal
2
Y:
M20/without ground terminal
ZE/ZV/XE/XV
Enclosed Switches
F-119
Advertisement
Table of Contents
Related Manuals for Omron XE
Summary of Contents for Omron XE
- Page 1 Enclosed Switches ZE/ZV/XE/XV Long Service Life and Large Breaking Power • ZE, ZV, and ZV2 incorporate Model Z Basic Switches with rug- ged diecast cases. • Available with various models of built-in switches (including split contact model, maintained operation type, magnetic blowout model) and various actuators.
-
Page 2: Ordering Information
Note: 1. The diagonal side mounting model feature improved sealing property, improved mounting strength through use of M5 screws, increased stability in seating with large mounting width (31 x 75 mm) and permit coupling of a number of Switch units. - Page 3 2. IP65 for @E-N models and IP60 for @E-Q models. 3. The values are calculated at an operating temperature of 5 C to 35 C, and an operating humidity of 40% to 70%. Contact your OMRON sales representative for more detailed information on other operating environments.
- Page 4 0.72 mm 0.4 mm 75.2 0.8 mm (ZV-Q22-2, XV-Q21-2) (see note 3) Note: 1. The OP of ZV2-Q-2/XV2-Q-2 is 24.2 0.8 mm. 2. The OP of ZV2-Q22-2/XV2-Q22-2 is 35.7 1 mm. 3. The OP of ZV2-Q21-2/XV2-Q21-2 is 35.7 0.8 mm.
-
Page 5: Engineering Data
■ Contact Form ZE-@, ZV-@, ZV2-@ XE-@, XV-@, XV2-@ EN60947-5-1 Note: With the XE-@, XV-@, and XV2-@, be sure to connect COM to the + terminal. Engineering Data ■ Electrical Durability ZE (cosφ = 1) XE (L/R = 0) Operating frequency:... -
Page 6: Side Mounting
Note: 1. All units are in millimeters unless otherwise indicated. 2. Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. 3. In the drawings for the Base Mounting Type Switches (ZV), the mounting surfaces (flanges) are shown by lines of alternate long and two short dashes. - Page 7 Roller Arm Lever 19.1 dia. × 7.9 (see note 1) (See note 2) ZE-QA2-2, XE-QA2-2 39.7 (23.1) JIS B0202 G1/2 Effective thread: Two, M4 4 threads min. 44±0.8 (length: 45) 19.3 25.5 Note: 1. Stainless sintered roller 2. Adjustable between 0° and 225°...
- Page 8 Sealed Roller Arm Lever 19.1 dia. × 7.9 (see note 1) ZE-NA2-2, XE-NA2-2 (See note 2) 39.7 (23.1) JIS B0202 G1/2 Effective thread: Two, M4 4 threads min. 53.4±0.8 (length: 45) 19.3 25.5 Note: 1. Stainless steel roller ±0.1 25.4±0.3 2.
- Page 9 ZV(2)-Q22-2, XV(2)-Q22-2 t = 3 (ZV-Q22-2/XV-Q22-2 flange) 41.3±0.2 ± 10.5 36.6 Two, 4.3±0.2 dia. holes 12.7 dia. × 4.8 (see note 1) 26.1 JIS B0202 G1/2 OP (see note 3) Effective thread: 4 threads min. Note: 1. Stainless steel roller 2.
- Page 10 OP (see note 3) 2. Only the ZV2-N22-2 incorpo incorpo- thread: 4 rate mounting holes. OP (see note 4) threads min. 3. OP for ZV2-N22-2 is 35.7 0.8 mm. 31±0.2 75±0.2 25.4±0.3 +0.2 Two, 5.4 dia. holes (see note 2)
- Page 11 Sealed Crossroller Plunger t = 3 (ZV flange) ZV(2)-N21-2 41.3±0.2 10.6±0.3 Two, 4.3±0.2 dia. holes 36.6 12.7 dia. × 4.8 (see note 1) 26.1 JIS B0202 G1/2 Effective thread: 4 threads min. OP (see note 3) OP (see note 4) 31±0.2...
-
Page 12: Operation
Make sure that the nut is free of foreign substances when the nut is loosened. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. In the interest of product improvement, specifications are subject to change without notice. Cat. No. C020-E1-09...